Monogram ZIP75BB Installation Guide

Installation Instructions

Automatic Icemaker

3/4″ Thick Custom Panel Kit

ZIP75WW, ZIP75BB

NOTE: If installing a 3/4″ trimless custom panel, a 1-1/2″ wide filler strip may be required. The filler strip will act as a spacer between the icemaker case and the adjacent cabinet, and will prevent interference with the icemaker door swing when it is installed between frameless or framed cabinetry. The width of the cutout opening must include the width of the filler strip. The product cannot be installed flush to adjacent 24″ deep cabinets with a 3/4″ thick custom panel.

This kit contains a new handle and two side mounting brackets to support a trimless custom door panel up to 3/4″ thick. A custom handle may replace the supplied handle.

IMPORTANT:

• Cut edges of the custom door panel will be seen and must be finished for best appearance. The back side of the panel should be finished a minimum of 1/2″ on all sides.

• The custom panel, both raised and flat design, should be constructed in the same manner as typical cabinet doors.

• Order the custom panel from the cabinet manufacturer. Be sure to provide the exact dimensions so that the panel is constructed accurately.

• BEFORE YOU BEGIN:

Read these instructions completely and carefully.

•

IMPORTANT:

Save these instructions for local inspector’s use.

•

IMPORTANT:

Observe all governing codes and ordinances.

• Note to Installer – Be sure to leave these instructions with the Consumer.

• Note to Consumer – Keep these instructions with your Owner’s Manual for future reference.

WARNING:

Disconnect electrical power supply to icemaker before installing front panel. Do not operate icemaker while installing panel. Failure to do so can result in death, fire, or electrical shock.

AVERTISSEMENT :

Il faut debrancher l’alimentation de la machine à glaçons avant d’installer le panneau avant. La machine à glaçons ne doit pas être en marche pendant l’installation du panneau avant. Le non-respect de ces instructions peut causer la mort, un incendie ou un choc électrique.

Kit Contents:

• 2 side trim pieces

• 8 side trim screws

• Door handle

Tools and Materials Required:

• 8 flat head wood screws, 1/2″ long

• Drill and 1/8″ bit

• Safety glasses

• Tape

• Custom panel

WARNING

AVERTISSEMENT

Handle

Left Trim

29-1/2"

Custom

Panel

14-23/32"

Right Trim

Pub. No. 49-60043-3 Part No. 197D2521P001

02-06 JR

ZIP75WW–2313617 ZIP75BB–2313618

Printed in the United States

NOTE: While performing installations described in this book, safety glasses or goggles should be worn.

For Monogram®local service in your area, call

1.800.444.1845.

NOTE: Product improvement is a continuing endeavor at General Electric. Therefore, materials, appearance and specifications are subject to change without notice.

GE Consumer & Industrial

GE Appliances General Electric Company Louisville, KY 40225

ge.com

Installation Instructions

DISCONNECT POWER TO THE ICE MACHINE

STEP 1

REMOVE HANDLE AND NAMEPLATE

• Remove the door handle by removing the two top mounting screws. Set screws aside. Discard handle.

• The Monogram nameplate is held in place with adhesive. Remove the nameplate.

STEP 2

INSTALL ASSEMBLED PANEL ONTO THE ICE MACHINE

• Install panel to icemaker with supplied screws, four on each side.

STEP 6

INSTALL SUPPLIED DOOR HANDLE (IF USED)

• Install the new supplied handle with original screws.

STEP 7

MARK MOUNTING SCREW LOCATIONS

• Align and hold the side trim pieces against the icemaker door and mark screw locations on the sides.

• Drill 1/8″ pilot holes into the door sides of the icemaker.

STEP 3

SECURE SIDE TRIM PIECES TO CUSTOM PANEL

• Lay the custom panel appearance-side-down on a clean surface.

• Align top and bottom side trim to the custom panel sides.

• Tape the side trim pieces to the back of the custom panel.

• Place the panel with trim against the door to be sure that trim and panel fits the door side to side and top to bottom. Adjust as needed.

• Mark screw locations and remove trim. Drill pilot holes.

• Install side trim to the back side of the custom panel with screws (not supplied). Use flat head wood screws approximately 1/2″ long.

STEP 5

SECURE CUSTOM HANDLE TO CUSTOM PANEL. (SKIP THIS STEP IF YOU ARE USING THE SUPPLIED HANDLE)

A custom handle can be installed onto the 3/4″ thick panel, replacing the supplied handle.

• The custom handle can be installed at the top or side of the panel.

• Drill pilot holes through the front of the custom panel to match the chosen handle.

• Secure the handle to the panel with flat head wood screws.

• Replace original handle screws in the top of the door frame.

STEP 4