Monogram ZIC30GNZII, ZIK30GNZII User Manual

ZIC30GNZII/ZIK30GNZII

Height options
80” or * 84“

25” min. depth

30” Finished Width

GE Monogram® 30" Fully Integrated Customizable Refrigerators with
Convertible Drawer

Dimensions and Installation Information (in inches)

The Installation Space

The finished cutout width must be 30".

23-3/4”

The cutout depth must be 25" for flush installations.

• The front face of the refrigerator fits flush with 25" depth
adjacent cabinets.

Electrical

A 115V, 60Hz., 15 or 20 amp power supply is required. An
individual properly grounded branch circuit or circuit breaker
is recommended. Install a properly grounded 3-prong
electrical receptacle recessed into the back wall. Electrical
must be located on rear wall as shown.

Note: GFI (ground fault interrupter) is not recommended.

Water Line

• A cold water supply is required for automatic icemaker
operation. The water pressure must be between 40 and 120

p.s.i.

• Route 1/4" OD copper or GE SmartConnect™ plastic
tubing between the house cold water line and the water
connection location.

• Tubing should be long enough to extend to the front of the
refrigerator. Allow enough tubing to accommodate a bend
leading into the water line connection.

• Water line can enter an opening through the floor or back wall.

• Install a shut-off valve between the icemaker water valve
and cold water cupply in the home.

3/4”

29-3/4”

Height adjustable

from 79-3/8” to 80-3/8” *

1/8”

4”

For answers to your Monogram,® GE Profile™ or
GE® appliance questions, visit our website at
geappliances.com or call GE Answer Center®
service, 800.626.2000.

1-1/4”

4”

Listed by
Underwriters
Laboratories

Specification Revised 3/12

110118

ZIC30GNZII/ZIK30GNZII

GE Monogram® 30" Fully Integrated Customizable Refrigerators with
Convertible Drawer

Dimensions and Installation Information (in inches)

Customization Basics:

These refrigerators are factory set for a right hinged door
swing. The door swing is reversible. Choose an RH model
with hinge on the right side; the door swings left to right.
Choose an LH model with hinge on the left side; the door will
swing right to left.

Note:

For 84" panels, the top space behind the top panel can be
enclosed with wood and stained by the cabinet maker to
match adjacent cabinetry.

Door Handles

Custom handles of your choice, supplied by your
cabinetmaker, can be installed. If desired, you may order
WR12X10988 Monogram® European stainless steel tubular
handle kit for custom panels.

Optional Accessory Kits

ZUG30: For side-by-side installation
European Handle Kit: can be purchased through GE Parts

store - WR12X10988

Door Swing Clearances

The installation must allow for clearances to adjacent walls or
cabinets. These refrigerators are equipped with a 2-position
door stop. The factory-set 115° door swing can be adjusted to
90° if clearance to adjacent cabinets or walls is restricted.

Product Dimensions

For answers to your Monogram,® GE Profile™ or
GE® appliance questions, visit our website at
geappliances.com or call GE Answer Center®
service, 800.626.2000.

25"

130° Door Swing

130°

Min. to

Wall

90° Door Swing

90°

5" Min. for Professional Models

23-7/8"
Behind
Frame

36-3/4"

4" Min. to Wall

Allow 15" minimum clearances for a full 115° door swing.

• 5" minimum clearance is required when the door swing is
adjusted to 90°.

• See door swing illustrations to determine interaction with
adjacent cabinets or countertops.

Listed by
Underwriters
Laboratories

Specification Revised 3/12

110118

ZIC30GNZII/ZIK30GNZII

GE Monogram® 30" Fully Integrated Customizable Refrigerators with
Convertible Drawer

Dimensions and Installation Information (in inches)

SS PANEL ACCESSORY & DIMENSIONS

3/4"-Thick Solid Door Panel Options
For 80" High Installation

• European - Panel Model ZKST300N LH & RH capable

• Professional - Panel Model ZKSP300N LH & RH capable
For 84" High Installation the door panel is not reversible

for the 84" installations. A left or right-hand door panel
accessory must be purchased.

• LH European - Model ZKST304NLH

• RH European - Model ZKST304NRH

• LH Professional - Model ZKSP304NLH

• RH Professional - Model ZKSP304NRH
Note: Each kit also contains matching freezer and

cutomizable drawer panels, handles and toekick.

Optional Accessory Kits#:

• Side-by-Side Installation Kit - ZUG30

• European handle kit - 3 handles (can be purchased through
GE Parts) - WR12X10988

29-3/4”

3/4"-Thick Frame for Glass Door Options
For 80" High Installation

• European - Panel Model ZKGT300N LH & RH capable

• Professional - Panel Model ZKGP300N LH & RH capable
For 84" High Installation The door panel is not reversible

for the 84" installations. A left or right-hand door panel
accessory must be purchased. The top space behind the top
panel can be enclosed with wood and stained by the cabinet
maker to match adjacent cabinetry.

• LH European - Model ZKGT304NLH

• RH European - Model ZKGT304NRH

• LH Professional - Model ZKGP304NLH

• RH Professional - Model ZKGP304NRH
Note: Each kit also contains matching freezer and convertible

drawer panels, handles and toekick.

29-3/4”

Fresh

Food

Cabinets

Ice Drawer

Freezer

Convertible

Drawer

4”

1/8” Min.*

For answers to your Monogram,® GE Profile™ or
GE® appliance questions, visit our website at
geappliances.com or call GE Answer Center®
service, 800.626.2000.

45-3/8” for 80” Installation
49-3/8” for 84” Installation

7-1/2”

22-3/4”

23”

Glass Panel

6”

80”

Install.

10”
84”

Install.

for Fresh Food

45-3/8”

49-3/8”

6”

3-3/8”

*Pro style window is slightly smaller.

Note:

EXTREMELY IMPORTANT: Routing of custom wood panels is
required where the hooks and brackets attach to the panel.
Custom panels must be at least 3/4” thick where the hooks
and brackets hardware are attached.

Listed by
Underwriters
Laboratories

Specification Revised 3/12

110118