Monogram ZIF181NPNII, ZIF241NPNII, ZIR241NPNII, ZIF301NPNII User Manual
SIDE VIEW
W
24" (61.0)
2"
(5.1)
4 3/4"
(12.1)
7/16"
(1.1)
Trim overlap
3 1/2"
(8.9)
24" (60.9)
SIDE VIEW
24" (60.9)
3 1/2"
(8.9)
Finished
Return
Back
3/4"
(1.91)
W
MONOGRAM 42" BUILT-IN
COLUMNS RETROFIT
STANDARD INSTALLATION
*83 1/2" min
*84 1/2" max
(212.1-214.6)
*Trim will overlap
additional 7/16"
6"
(15.2)
5"
(12.7)
FRONT VIEW
41 1/2" (105.4)
E
5"
(12.7)
WATER
18" (45.7)
5"
(12.7)
From floor
of electrical
3 1/2"
(8.9)
75"
(190.5)
to bottom
area
C
3 1/2"
(8.9)
Finished
Return
e refrigerator will project forwa rd, slightly beyond adjacent cabinetry.
HELPFUL TIPS
C
A minimum 3 1/2" (8.9) finished return matching cabinet
exterior recommended on interior on all sides and top a t
front of opening
• In a side-by-side installa tion of a left-and-right-ha nd
door swing product, minimum 1/2" cleara nce between the
units is required. Also required is Side-by-Side Heater/
Dual Installation Kit, ZKUN, 42" trim kit, ZKR42N a nd 42"
stainless toekick ZKK42P.
Back
For retro fit installations, both units ca n be plugged into the
same electrical supply receptacle.
ATTENTION ELECTRICIAN:
A 115 volt 60Hz., 15 or 20 amp supply is recommended
for each product. An individual properly grounded branch
3/4"
(1.91)
W
circuit or circuit breaker is recommended. Install a
properly grounded 3-prong electrical receptacle recessed
into the back wall. Electrical must be located on rea r wall
as shown.
WARNING:
When installing appliance, you must use a nd follow
the product installation instructions. ese ca n be found
with unit or on web at monogra m.com.
is document is intended for cabinet a nd panel
construction only.
For questions about your
appliance, please call 1-800-626-2000.
Product Specication Revised 9/19PAGE 1 OF 8
MONOGRAM 42" BUILT-IN
COLUMNS RETROFIT
RETROFIT 3/4" PANEL DIMENSIONS DUAL
INSTALLATION WITH 18" FREEZER, ZIF181NPNII
AND 24" REFRIGERATOR, ZIR241NPNII
B
Door
Panel
PANEL DIMENSIONS
A B C
79 7/8" 17 9/16" 23 9/16"
C
Door
Panel
A
HELPFUL TIPS
• Refrigerators a nd freezers are designed to be customized
with decorative pa nels. Field-installed 3/4" custom door
panels a re required.
• Maximum total panel weight: 45 lbs
Note: For panels constructed with ra ils and stiles (5-panel),
the rails a nd stiles must be a minimum of 2" wide.
• For Custom Panels: Use templa tes provided with units
to pre-drill holes for mounting panel brackets (provided
with unit). Adjustment screws and instructions also
provided with units.
• Requires custom handle from ca binet maker.
• Stainless steel ha ndle and panel options:
ZK1SN189NLH: Left-hand 18" sta inless steel door panel
ZK1SN184NRH: Right-hand 18" sta inless steel door panel
ZK1SN249NLH: Left-hand 24" sta inless steel door panel
ZK1SN244NRH: Right-hand 24" sta inless steel door panel
ZKSP1H1CN: Minimalist handle for sta inless steel panels only
ZKSP1H1PN: Statement ha ndle for stainless steel panels only
For questions about your
appliance, please call 1-800-626-2000.
Product Specication Revised 9/19PAGE 2 OF 8
SIDE VIEW
W
24" (61.0)
2"
(5.1)
4 3/4"
(12.1)
7/16"
(1.1)
Trim overlap
3 1/2"
(8.9)
From floor
to bottom
of electrical
24"
24" (60.9)
3 1/2"
(8.9)
Finished
Return
Back
3/4"
(1.91)
W
MONOGRAM 48" BUILT-IN
COLUMNS RETROFIT
STANDARD INSTALLATION
(60.9)
SIDE VIEW
*83 1/2" min
*84 1/2" max
(212.1-214.6)
*Trim will overlap
additional 7/16"
5"
(12.7)
47 1/2" (120.7)
6"
E
(15.2)
5"
(12.7)
WATER
FRONT VIEW
20" (50.8)
5"
(12.7)
3 1/2"
(8.9)
75"
(190.5)
area
C
3 1/2"
(8.9)
Finished
Return
e refrigerator will project forwa rd, slightly beyond adjacent cabinetry.
HELPFUL TIPS
C
A minimum 3 1/2" (8.9) finished return matching cabinet
• A separa te 115V, 60Hz, 15- or 20-amp power supply is
exterior recommended on interior on all sides and top a t
recommended for each product. Additional cutout width
front of opening
may be required when side panels a re used.
• In a side-by-side installa tion of a left-and-right-ha nd
• In a side-by-side installation of a left-and-right-hand door
door swing product, minimum 1/2" cleara nce between the
swing product, 1" cleara nce between the units is required.
units is required. Also required is Side-by-Side Heater/
Order ZGUSS2 European, ZGUPP2 Professional or ZGU2
Dual Installation Kit, ZKUN, 42" trim kit, ZKR42N a nd 42"
custom panel unified grille kit for one continuous grille pa nel.
stainless toekick ZKK42P.
• In a side-by-side installa tion with same door swing, allow
2" minimum cleara nce between the products to prevent the
For retro fit installations, both units ca n be plugged into the
Back
door swing interference. Allow 15" minimum to a wall to
same electrical supply receptacle.
achieve full drawer extension and pa n removal. Additional
cleara nces are required when using custom panels a nd
handles. NOTE: ZGU2, ZGUSS2 or ZGUPP2 grille pa nel
ATTENTION ELECTRICIAN:
kits will not fit this installation.
A 115 volt 60Hz., 15 or 20 amp supply is recommended
• In a side-by-side installa tion with right and left door
for each product. An individual properly grounded branch
hinges together, allow 5" minimum cleara nce between the
circuit or circuit breaker is recommended. Install a
3/4"
(1.91)
W
two products to prevent one door from striking the other.
properly grounded 3-prong electrical receptacle recessed
Additional cleara nce required wen using custom panels and
into the back wall. Electrical must be located on rea r wall
handles. NOTE: ZGU2, ZGUSS2 or ZGUPP2 grille pa nel
as shown.
kits will not fit this installation.
WARNING:
When installing appliance, you must use a nd follow
the product installation instructions. ese ca n be found
with unit or on web at monogra m.com.
is document is intended for cabinet a nd panel
construction only.
For questions about your
appliance, please call 1-800-626-2000.
Product Specication Revised 9/19PAGE 3 OF 8
Loading...