Monogram ZICP720 Installation Instructions Manual
Professional Style
Bottom-Freezer Refrigerators
ZICP720
Design Guide
With Installation Instructions
49-60469
224D1234P001
07-06 JR
Installation
Instructions
Safety Information
2
BEFORE YOU BEGIN
Read these instructions completely and carefully.
• IMPORTANT — Save these instructions for
local inspector’s use. Observe all governing codes and
ordinances.
• Note to Installer — Be sure to leave these instructions
with the Consumer.
• Note to Consumer — Keep these instructions with your
Owner’s Manual for future reference.
WARNING:
This appliance must be properly grounded. See “Grounding
the Refrigerator,” page 6.
AVERTISSEMENT :
Cet appareil doit être correctement mis à la terre.
Consultez « Mise à la terre du réfrigérateur », page 6.
If you received a damaged refrigerator, you should
immediately contact your dealer or builder.
CAUTION:
Due to the weight and size of this refrigerator, and to reduce
the risk of personal injury or damage to the product—THREE
PEOPLE ARE REQUIRED FOR PROPER INSTALLATION.
PRUDENCE :
À cause du poids et de la taille de ce réfrigérator et pour réduire
le risque de blessure et de dommages, IL FAUT TROIS PERSONNES
POUR FAIRE L’INSTALLATION CORRECTEMENT.
Skill Level — Installation of this refrigerator requires
basic mechanical, carpentry and plumbing skills. Proper
installation is the responsibility of the installer. Product
failure due to improper installation is not covered under
the GE Appliance Warranty. See the Owner’s Manual for
warranty information.
WARNING:
• These refrigerators are top-heavy and must be secured
to prevent the possibility of tipping forward. Anti-Tip
protection is required. See pages 9 and 10 for details.
• Use this appliance only for its intended purpose.
• Immediately repair or replace electric service cords that
become frayed or damaged.
• Unplug the refrigerator before cleaning or making repairs.
• Repairs should be made by a qualified service technician.
AVERTISSEMENT :
• Ces réfrigérateurs sont lourds en haut et il faut les
arrimer pour éviter leur basculement. Il faut avoir un
système de protection contre le renversement. Voir
les détails pages 9 et 10.
• Il ne faut utiliser cet appareil que pour l’utilisation
appropriée.
• Réparez ou remplacez immédiatement tout cordon
électrique effiloché ou endommagé.
• Il faut débrancher le réfrigérateur avant le nettoyage
ou toute intervention.
• Les réparations doivent être faites par un technicien qualifié.
For Monogram local service in your area,
call 1.800.444.1845.
For Monogram service in Canada, call 1.888.880.3030.
For Monogram Parts and Accessories, call 1.800.626.2002.
www. monogram.com
CONTENTS
Planning Guide
The Installation Space ......................3
Dimensions and Clearances ..........3
130° Door Swing ..................................4
90° Door Swing ....................................5
Installation Instructions
Tools, Hardware, Trim,
Materials, Flooring ..............................6
Grounding the Refrigerator ............6
Step 1, Remove Packaging ............7
Step 2, Install Water Lines ..............7
Step 3, Install New Side Trim..........8
Step 4, Install Side Panels................8
Step 5, Install Anti-Tip Brackets....9
Step 6, Install New Top Trim........10
Step 7, Level Refrigerator..............10
Step 8, Alternate Anti-Tip
Procedure..............................11
Step 9, Secure Refrigerator
to Cabinetry ........................11
Step 10, Install Center
Trim Strip ............................12
Step 11, Install Grille Base Cover....12
Step 12, Remove Both Grille
Panels (if present) ..........13
Step 13, Install Grille Panel
Onto Hinges ......................13
Step 14, Adjust Door Swing..........14
Step 15, Connect Water Supply ..1
4
Step 16, Connect Power ................15
Step 17, Start Icemaker ................15
Step 18, Install Toekick ..................15
DIMENSIONS AND CLEARANCES
Product Clearances
These refrigerators are equipped with a 2-position
door stop. The factory set 130° door swing can be
adjusted to 90° if clearance to adjacent cabinets
or walls is restricted.
Allow 25″ minimum clearance for a full 130° door
swing. Allow 15″ for pan removal.
5″ minimum clearance is required when door swing
is adjusted to 90°. If the 90° door stop position is
used, pan access is maintained, but pan removal
is restricted.
See illustrations on pages
4 and 5 to determine door
swing interaction with
adjacent cabinets or
countertops.
Design Guide
THE INSTALLATION SPACE
The installation space must be 71-1/2″.
Water And Electrical Locations
Electrical and water supply must be located
as shown.
The cutout depth must be 24″
The refrigerator will project forward, slightly
beyond adjacent cabinetry, depending on your
installation.
Cutout depth beneath a soffit:
When installed beneath a soffit, the soffit cannot
exceed the 24″ installation depth shown. The top
case trim overlaps the bottom of the soffit.
Additional Specifications
•A separate 115 volt 60Hz., 15 or 20 amp power
supply is recommended for each product. An
individual properly grounded branch circuit or
circuit breaker is recommended. Install properly
grounded 3-prong electrical receptacles recessed
into the back wall. Electrical must be located on
rear wall as shown.
NOTE: GFI (ground fault interrupter) is not
recommended.
• Both water lines can enter the opening through
the floor or back wall. Route GE SmartConnect
™
kit or 1/4″ O.D. copper tubing between the cold
water line and the water connection location.
The tubing should be long enough to extend to
the front of the refrigerator. Installation of an
easily accessible shut-off valve in the water
line is required.
90° Door
Swing
* Shipping height. The
refrigerators can be
adjusted to fit into a
cutout that is 83-1/2″
min. to 84-1/2″ max.
Note that the top case
trim at the front is 1/2″
higher and will overlap
upper cabinetry or
soffit. Use leveling legs
and wheels for a
maximum 1″ height
adjustment.
83-1/2″
at Rear
28-11/16″
Depth Including
Handles
72″ Frame
to Frame
Width
84″
71-1/2″
Case Width
25-3/4″
Case Depth
25″
Min. to
Wall
25″
Min. to
Wall
130° Door
Swing
130° Door
Swing
36-3/4″
90°
5″ Minimum to
Wall
3
23-7/8″
Behind
Frame
71-1/2″ Finished Width
2-5/16″
Electrical
24-3/16″
6″
6″
10″
Wall
View
26″
5″
5″
26″
10″
75″ From
Finished
Floor to
Bottom of
Electrical
Area
3-1/2″
Water Supply
Water Supply
3-1/2″
84-1/2″
max
83-1/2″
min
Finished
Opening
24″ Cutout
Depth
0″
71-1/2"
Case Width
83-1/2"
at Rear
28-11/16" Depth
Including Handles
25"
Min. to
Wall
130° Door
Swing
25-3/4"
Case Depth
*84"
72" Frame to
Frame Width
0"
130° Door
*Shipping height. The
refrigerators can be adjusted
to fit into a cutout that is
83-1/2" min. to 84-1/2" max.
Note that the top case trim
at the front is 1/2" higher and
will overlap upper cabinetry
or soffit. Use leveling legs
and wheels for a maximum
1" height adjustment.
25"
Min. to
Wall
Swing
23-7/8"
Behind
Frame
90°
36-3/4"
4" Minimum
to Wall
1/4"
1/2"
3/4"
1"
1-1/4"
1"
3/4" Overlay
Panel
(Nominal Size)
Stainless Steel
1/4"
1/2"
3/4"
2"
1-1/4"
1-1/2"
1-3/4"
3"
2-1/4"
2-1/2"
2-3/4"
1/4"
1/2"
3/4"
Door
23-7/8" From
Rear of
Refrigerator
1"
Refrigerator
Case
Trim
Top View
130° DOOR SWING
(factory setting)
Scale 1:1
4
Frameless Cabinets: The case trim
overlaps cabinets at the top and sides.
Therefore, frameless cabinets may require
filler strips to prevent interference with
cabinet door swing. The opening must
allow for filler strips.
Design Guide
1/4"
1/2"
3/4"
1"
1-1/4"
1/4"
1/2"
3/4"
1"
1-1/4"
1-1/2"
23-7/8"
From Rear of
Refrigerator
3/4" Overlay
Panel
(Nominal Size)
Case Trim
Refrigerator
Door
Stainless Steel
5
Top View
90° DOOR SWING
(optional setting)
Scale 1:1
Frameless Cabinets: The
case trim overlaps cabinets
at the top and sides.
Therefore, frameless
cabinets may require
filler strips to prevent
interference with cabinet
door swing. The opening
must allow for filler strips.
Design Guide
Loading...