Monogram ZIC30GNHII Specification Sheet
MONOGRAM 30" FULLY INTEGRATED CUSTOMIZABLE
Height options
80” or * 84“
25” min. depth
30” Finished Width
60" Finished Width
Wall
View
84"
max
80"
min
Finished
Opening
25" min. Cutout
Depth
77"
6"
Anti-tip location do not obstruct
Water Tube & Electrical Outlet
ZIC30GNHII/
REFRIGERATORS FOR DUAL INSTALLATION
DIMENSIONS AND INSTALLATION INFORMATION (IN INCHES)
The Installation Space
The finished cutout width must be 30".
23-3/4”
3/4”
The cutout depth must be 25" for flush installations.
- The front face of the refrigerator fits flush with 25" depth
adjacent cabinets.
Electrical
A 115V, 60Hz., 15 or 20 amp power supply is required. An
individual properly grounded branch circuit or circuit breaker
is recommended. Install a properly grounded 3-prong electrical
receptacle recessed into the back wall. Electrical must be located
on rear wall as shown.
Note: GFI (ground fault interrupter) is not recommended.
Water Line
- A cold water supply is required for automatic
icemaker operation. The water pressure must be
between 40 and 120 p.s.i.
- Route 1/4" OD copper or GE SmartConnect™ plastic
tubing between the house cold water line and the
water connection location.
- Tubing should be long enough to extend to the
front of the refrigerator. Allow enough tubing to
accommodate a bend leading into the water line
connection.
- Water line can enter an opening through the floor or
back wall.
- Install a shut-off valve between the icemaker water
valve and cold water supply in the home.
ZIK30GNHII
Height adjustable
from 79-3/8” to 80-3/8” *
29-3/4”
4”
1/8”
3-1/8”
1-1/4”
4”
Note: When two units are placed side
by side, order heater kit ZUG30.
Listed by
Underwriters
Laboratories
Product Specification Revised 7/16
MONOGRAM 30" FULLY INTEGRATED CUSTOMIZABLE
25"
ZIC30GNHII/
REFRIGERATORS FOR DUAL INSTALLATION
DIMENSIONS AND INSTALLATION INFORMATION (IN INCHES)
Customization Basics:
These refrigerators are factory set for a right hinged
door swing. The door swing is reversible. Choose
an RH model with hinge on the right side; the door
swings left to right. Choose an LH model with hinge
on the left side; the door will swing right to left.
Note:
For 84" panels, the top space behind the top panel
can be enclosed with wood and stained by the
cabinet maker to match adjacent cabinetry.
Door Handles
Custom handles of your choice, supplied by your
cabinetmaker, can be installed. If desired, you may
order WR12X10988 Monogram European stainless
steel tubular handle kit for custom panels.
Optional Accessory Kits
ZUG30: For side-by-side installation
European Handle Kit: can be purchased through
GE Parts store - WR12X10988
Door Swing Clearances
The installation must allow for clearances to adjacent
walls or cabinets. These refrigerators are equipped
with a 2-position door stop. The factory-set 115°
door swing can be adjusted to 90° if clearance to
adjacent cabinets or walls is restricted.
Product Dimensions
ZIK30GNHII
130° Door Swing
130°
Min. to
Wall
90° Door Swing
90°
5" Min. for Professional Models
23-7/8"
Behind
Frame
36-3/4"
4" Min. to Wall
Allow 15" minimum clearances for a full 115° doorswing.
- 5" minimum clearance is required when the door
swing is adjusted to 90°.
- See door swing illustrations to determine interaction
with adjacent cabinets or countertops.
Listed by
Underwriters
Laboratories
Product Specification Revised 7/16
MONOGRAM 30" FULLY INTEGRATED CUSTOMIZABLE
3-3/8”
ZIC30GNHII/
REFRIGERATORS FOR DUAL INSTALLATION
DIMENSIONS AND INSTALLATION INFORMATION (IN INCHES)
SS PANEL ACCESSORY & DIMENSIONS
3/4"-Thick Solid Door Panel Options
For 80" High Installation
- European - Panel Model ZKST300N
LH & RH capable
- Professional - Panel Model ZKSP300N
LH & RH capable
For 84" High Installation the door panel is not
reversible for the 84" installations. A left or righthand door panel accessory must be purchased.
- LH European - Model ZKST304NLH
- RH European - Model ZKST304NRH
- LH Professional - Model ZKSP304NLH
- RH Professional - Model ZKSP304NRH
Note: Each kit also contains matching freezer and
cutomizable drawer panels, handles and toekick.
Optional Accessory Kits#:
- Side-by-Side Installation Kit - ZUG30
- European handle kit - 3 handles (can be purchased
through GE Parts) - WR12X10988
3/4"-Thick Frame for Glass Door Options
For 80" High Installation
- European - Panel Model ZKGT300N
LH & RH capable
- Professional - Panel Model ZKGP300N
LH & RH capable
For 84" High Installation The door panel is not
reversible for the 84" installations. A left or righthand door panel accessory must be purchased. The
top space behind the top panel can be enclosed
with wood and stained by the cabinet maker to
match adjacent cabinetry.
- LH European - Model ZKGT304NLH
- RH European - Model ZKGT304NRH
Note: Each kit also contains matching freezer and
convertible drawer panels, handles and toekick.
ZIK30GNHII
29-3/4”
Cabinets
4”
29-3/4”
Fresh
Food
Ice Drawer
Freezer
Convertible
Drawer
1/8” Min.*
45-3/8” for 80” Installation
49-3/8” for 84” Installation
7-1/2”
22-3/4”
23”
Glass Panel
6”
80”
Install.
10”
84”
Install.
for Fresh Food
45-3/8”
49-3/8”
6”
*Pro style window is slightly smaller.
Note:
EXTREMELY IMPORTANT: Routing of custom wood
panels is required where the hooks and brackets
attach to the panel. Custom panels must be at least
3/4" thick where the hooks and brackets hardware
are attached.
Listed by
Underwriters
Laboratories
Product Specification Revised 7/16
Loading...