Page 1
MONOGRAM BAR REFRIGERATOR
WITH ICEMAKER
ZIBS240NSS
When ordering this product,
be sure to use the model number
associated with the chosen handle.
Statemenet handle
ZXGP1H1PPSS
Minimalist handle
ZXGP1H1CPSS
MINIMALIST HANDLE
Model is shown with the Minimalist
handle, which needs to be ordered
separately. To order this handle use
model number ZXGP1H1CPSS.
DIGITAL TOUCH CONTROLS
Provide precise temperature settings for cooling all types
of fresh foods and beverages, a nd a LED display allows
easy viewing of temperatures
AUTOMATIC ICEMAKER WITH REMOVABLE
ICE BIN
Makes up to 8 pounds of ice per day
SPACIOUS INTERIOR WITH REMOVABLE
SPILLPROOF GLASS SHELVES AND
FULL-EXTENSION WINE RACKS
Accommodates beverages a nd fresh foods of all
types and sizes, a nd puts them all within easy reach
SOFT INTERIOR LED LIGHTING
Automatically illumina tes when the door is open, but can be
activated by a n internal on/off switch
CONVENIENT 24" CONFIGURATION
Is fully finished on all sides to allow installation virtually
anywhere in the home
FLUSH INSET INSTALLATION CAPABLE
Allows near-sea mless integration with surrounding cabinetry
For questions about your
appliance, please call 1-800-626-2000.
PAGE 1 OF 3
Product Specication Revised 10/19
Page 2
SPECIFICATIONS
Overall Width 23 1/2" (59.7 cm)
Overall Height 34 1/8" (86.7 cm)
Overall Depth 23 3/16" (58.9 cm)
9 3/8" (23.8 cm) @ 110°
2" (5.1 cm) @ 90°
Door Clearance
23 7/8" (60.6) door length
Overall Capacity 4.25 cu. ft.
Minimum Cabinet Width 23 3/4" (60.3 cm)
Minimum Cabinet Depth 24" (61.0 cm)
Cutout Width 23 3/4" (60.3 cm)
34 1/2" (87.6 cm) Min
Cutout Height
35" (88.9 cm) Max
Electrical Requirements 2.0 A
Voltz/Hertz/Amps 120 V, 60 Hz, 15 or 20 amp circuit
Shipping Weight 144 lb (65.5 kg)
OVERALL DIMENSIONS
23 5/8" (60.0)
FRONT VIEW
25 1/2" (64.5)
23 1/2" (59.7)
21 3/4" (55.2)
SIDE VIEW
23 5/8" (60.0)
34 1/8"
(86.7)
ATTENTION ELECTRICIAN:
A 115 volt 60Hz, 15 or 20 amp power supply is required. An
individual properly grounded branch circuit or circuit breaker
is recommended. Install a properly grounded 3-prong electrical
receptacle recessed into the back wall.
For questions about your
appliance, please call 1-800-626-2000.
PAGE 2 OF 3
9 3/8"
(23.8)
2"
(5.1)
23 7/8"
TOP VIEW
(60.6)
(SHOWING
DOOR SWING)
Dimensions in parentheses a re in centimeters unless otherwise noted.
Actual product dimensions may vary due to ma nufacturing tolerances.
Product Specication Revised 10/19
Page 3
ELECTRIC/
WATER
10 1/2" (26.7)
1 1/2" (3.8)
23 3/4" (60.3)
min standard
24" (61.0)
min flush inset
9"
(22.9) max
ZIBS240PSS
INSTALLATION NOTES
INSTALLATION CUTOUT
SIDE VIEW
24" (61.0)
min cutout depth
34 1/2"
(87.6) min
underside of
counter to floor
35" (88.9) max
REFRIGERATION MODULES, TOP VIEW
23 3/4" min.
INSTALLATION CUTOUT
FRONT VIEW
23 3/4" (60.3)
min standard
24" (61.0)
min flush inset
10 1/2" (26.7)
9"
(22.9) max
ELECTRIC/
WATER
1 1/2" (3.8)
24" min. width
stainless steel models
• Installation Space
is module can be installed
beneath a countertop or can be
used free-standing.
• For a sta ndard installation of
stainless steel unit: e product
must be installed so that the front
face will project 2-5/8" forward of
adjacent cabinets.
• For a flush installa tion of stainless
steel unit: Install a 1" wide filler strip
on the hinge side. e width of the
opening must be 24" min. wide. See
installation instructions for deta ils.
• Location Requirements: All
Monogram Refrigera tion Modules
may be closed in on the top and sides
as long as the front is unobstructed
for air circula tion and door swing.
Do not install these products where
the temperatures will go below 55° F
(13 C) or above 90° F (32 C).
Products must operate from sepa rate
properly grounded receptacles.
ese products are not designed to
be stacked one over the other.
Standard
Installation
CABINET CABINET
Dim. A
In a standard installation, the
product will project forward of
adjacent cabinets. See Dim. A.
Front Edge of
Product Case
Front Face
110º
120º
PRODUCT DIM. A
ZDWI240, ZDB1240 2"
ZDWR240, ZDBR240 1-3/4"
ZIFS240, ZIF1240 1-5/8"
ZDOD240 1-7/8"
ZIB1240, ZIBS240 2-5/8"
For questions about your
appliance, please call 1-800-626-2000.
Flush
Installation
Filler panel or cleat to be set
back even with front of case.
CABINET CABINET
These products will fit flush to adjacent
cabinets when installed with a Dim. A - width
filler panel or cleat. The filler panel should be
recessed or set back behind the door and
even with the front edge of the product case.
Front Edge of
Product Case
Front Face
Dim. A
110º
120º
PRODUCT DIM. A
ZDWI240, ZDB1240 1"
ZDWR240, ZDBR240 1"
ZIB1240, ZIF1240 1"
ZIFS240, ZIBS240 1/4"
ZDOD240 1-1/4"
See installation instructions for
side-by-side information.
Product Specication Revised 10/19PAGE 3 OF 3
Loading...