Page 1
MONOGRAM WINE RESERVE
ZDWR240NBS
When ordering this product,
be sure to use the model number
associated with the chosen handle.
Statemenet handle
ZXGW1H1PPSS
Minimalist handle
ZXGW1H1CPSS
MINIMALIST HANDLE
Model is shown with the Minimalist
handle, which needs to be ordered
separately. To order this handle use
model number ZXGW1H1CPSS.
DIGITAL TOUCH CONTROLS
Provides precise temperature settings essential for aging or serving
wine, and a LED display allows easy viewing of temperatures
FULL-EXTENSION SLIDING WINE RACKS
Holds up to 57 bottles positioned either horizontally or vertically
to maximize space and ca n be removed for larger bottles
UV RESISTANT, TEMPERED GLASS DOOR
Affords a full view of wine reserve contents while protecting
what is inside
SOFT INTERIOR LED LIGHTING
Automatically illumina tes when the door is open, but can be
activated by a n internal on/off switch
CONVENIENT 24" CONFIGURATION
Is fully finished on all sides to allow installation virtually
anywhere in the home
FLUSH INSET INSTALLATION CAPABLE
Allows near-sea mless integration with surrounding ca binetry
REVERSIBLE DOOR SWING
Easily reversed to left or right door swing as needed
For questions about your
appliance, please call 1-800-626-2000.
PAGE 1 OF 3
Product Specication Revised 10/19
Page 2
OVERALL DIMENSIONS
23 1/2" (59.7)
FRONT VIEW
33 7/8"
(86.0)
SPECIFICATIONS
Overall Width 23 1/2" (59.7 cm)
Overall Height 33 7/8" (86 cm)
Overall Depth 23 3/8" (59.4 cm)
9 3/8" (23.8 cm) @ 110°
2" (5.1 cm) @ 90°
Door Clearance
23 1/4" (59.1) door length
Overall Capacity 5.5 cu. ft.
Minimum Cabinet Width 23 3/4" (60.3 cm)
Minimum Cabinet Depth 24" (61.0 cm)
Cutout Width 23 3/4" (60.3 cm)
34 1/2" (87.6 cm) Min
Cutout Height
35" (88.9 cm) Max
Electrical Requirements 1.2 A
Voltz/Hertz/Amps 120 V, 60 Hz, 15 or 20 amp circuit
Shipping Weight 162 lb (73.5 kg)
ATTENTION ELECTRICIAN:
A 115 volt 60Hz, 15 or 20 amp power supply is required. An
individual properly grounded branch circuit or circuit breaker
is recommended. Install a properly grounded 3-prong electrical
receptacle recessed into the back wall.
25 5/8" (65.1)
23 1/2" (59.7)
21 1/2" (54.6)
SIDE VIEW
23 5/8" (60.0)
9 3/8"
(23.8)
2"
(5.1)
For questions about your
appliance, please call 1-800-626-2000.
PAGE 2 OF 3
23 1/4"
TOP VIEW
(59.1)
(SHOWING
DOOR SWING)
Dimensions in parentheses a re in centimeters unless otherwise noted.
Actual product dimensions may vary due to ma nufacturing tolerances.
Product Specication Revised 10/19
Page 3
10 1/2" (26.7)
24 1/4" (61.6) Min
Flush Inset
9" (22.9)
Max
ELECTRIC
23 3/4" (60.3) Min
cutout width
ZDBC240NBS
INSTALLATION NOTES
INSTALLATION CUTOUT
SIDE VIEW
24"
(61.0)
min cutout depth
34 1/2"
(87.6)
Min
underside of
counter to floor
35" (88.9) Max
REFRIGERATION MODULES, TOP VIEW
23 3/4" min.
Standard
Installation
CABINET CABINET
Dim. A
In a standard installation, the
product will project forward of
adjacent cabinets. See Dim. A.
Front Edge of
Product Case
Front Face
110º
120º
INSTALLATION CUTOUT
FRONT VIEW
23 3/4" (60.3) Min
cutout width
24 1/4" (61.6) Min
Flush Inset
10 1/2" (26.7)
9" (22.9)
Max
ELECTRIC
1 1/2" (3.8)
24 1/4" min. width
stainless steel models
Flush
Installation
Filler panel or cleat to be set
back even with front of case.
CABINET CABINET
These products will fit flush to adjacent
cabinets when installed with a Dim. A - width
filler panel or cleat. The filler panel should be
recessed or set back behind the door and
even with the front edge of the product case.
Front Edge of
Product Case
Front Face
110º
120º
Dim. A
• Installation Space
is module can be installed
beneath a countertop or can be
used free-standing.
• For a sta ndard installation of
stainless steel unit: e product
must be installed so that the front
face will project 2-5/8" forward of
adjacent cabinets.
• For a flush installa tion of stainless
steel unit: Install a 1" wide filler strip
on the hinge side. e width of the
opening must be 24" min. wide. See
installation instructions for deta ils.
• Location Requirements: All
Monogram Refrigera tion Modules
may be closed in on the top and sides
as long as the front is unobstructed
for air circula tion and door swing.
• Do not install these products where
the temperatures will go below 55° F
(13 C) or above 90° F (32 C).
• Products must operate from sepa rate
properly grounded receptacles.
• ese products are not designed to
be stacked one over the other.
See installation instructions for
side-by-side information.
PRODUCT DIM. A
ZDWI240, ZDB1240 2"
ZDWR240, ZDBR240 1-3/4"
ZIFS240, ZIF1240 1-5/8"
ZDOD240 1-7/8"
ZIB1240, ZIBS240 2-5/8"
For questions about your
appliance, please call 1-800-626-2000.
PRODUCT DIM. A
ZDWI240, ZDB1240 1"
ZDWR240, ZDBR240 1"
ZIB1240, ZIF1240 1"
ZIFS240, ZIBS240 1/4"
ZDOD240 1-1/4"
Product Specication Revised 10/19PAGE 3 OF 3
Loading...