Monogram ZDP48L6RWSS, ZDP48N6RWSS, ZDP48L6DWSS, ZDP36N6WSS, ZDP36N4RWSS Installation Instructions Manual
...
GE Monogram
Installation
Instructions
®
Professional
Ranges
48" Natural Gas Models
ZDP48N4GWSS
ZDP48N6RWSS
ZDP48N6DWSS
48" LP Gas Models
ZDP48L4GWSS
ZDP48L6RWSS
ZDP48L6DWSS
36" Natural Gas Models
ZDP36N6WSS
ZDP36N4RWSS
ZDP36N5DWSS
36" LP Gas Models
ZDP36L6WSS
ZDP36L4RWSS
ZDP36L4DWSS
CAUTION
WARNING
Before you begin—Read these instructions completely and carefully.
IMPORTANT: Save these instructions for local inspector’s use.
IMPORTANT: OBSERVE ALL GOVERNING CODES AND ORDINANCES.
NOTE TO INSTALLER: Be sure to leave these instructions with the Consumer.
NOTE TO CONSUMER: Keep these instructions with your Use and Care Book for future
reference.
This appliance must be properly grounded. See “Electric Supply”, page 7.
If you have questions concerning the installation of this product, call the GE Answer
Center® Consumer Information Service at
800.626.2000, 24 hours a day, 7 days a week.
If you received a damaged range, you should
contact your dealer.
Installation of this range requires basic
electrical, carpentry and mechanical skills.
Proper installation is the responsibility of the
installer. Product failure due to improper
installation is not covered under the GE
Appliance Warranty. See the back cover of the
Use & Care Guide for warranty information.
Contents
CAUTION:
THESE RANGES MUST BE INSTALLED IN
CONJUNCTION WITH A SUITABLE OVERHEAD VENT HOOD. Due to the high heat
capacity of this unit, particular attention
should be paid to the hood and duct work
installation to assure it meets local building
codes.
Check local building codes for the proper
method of gas range installation. Local codes
vary. Installation, electrical connections and
grounding must comply with applicable codes.
In the absence of local codes, the gas cooktop
should be installed in accordance with the
National Fuel Gas Code ANSI 223.1-1990 and
National Electrical Code ANSI/NFPA 70-1990.
Standard installations:
48" Ranges require a 800 to 1200 CFM Hood.
36" Ranges require 600 to 800 CFM Hood.
Hoods should be 24" min. deep and the same
width as the cooktop.
CAUTION:
These ranges weigh up to 600 pounds. Some
disassembly will reduce the weight considerably. Due to the weight and size of the range
and to reduce the risk of personal injury or
Island installations:
48" Ranges require a 800 to 1200 CFM Hood.
damage to the product, TWO PEOPLE ARE
REQUIRED FOR PROPER INSTALLATION.
36" Ranges require 600 to 1200 CFM Hood.
Hoods should be 30" min. deep and 36" wide
at the bottom.
Note: When installing a range that includes a
grill, select a blower on the high end of CFM
recommendation.
Design Information
Models Available..................................................................................................................................3
Accessor y Requirements .....................................................................................................................3
Models Dimensions and Clearances...............................................................................................4,5
Advance Planning ...............................................................................................................................6
Installation Preparation
Tools & Materials Required ................................................................................................................7
Power Supply Locations......................................................................................................................7
Installation
Step 1: Remove Packaging..................................................................................................................8
Step 2: Level the range .......................................................................................................................9
Step 3: Connect Range to Gas............................................................................................................9
Step 4: Install the Range Backguard..................................................................................................9
Step 5: Connect Electrical ................................................................................................................10
Step 6: Slide Range Into Position ....................................................................................................10
Step 7: Replace Oven Doors.............................................................................................................10
Step 8: Assemble & Adjust Burners .................................................................................................11
Step 9: Adjustable Low Burner Settings ..........................................................................................11
Finalize Installation...........................................................................................................................11
2
Design Information
Professional Ranges
Models
Available
These ranges are factory set for either natural
gas or liquid propane gas. Order the model
for your installation situation.
48" Natural Gas Models:
ZDP48N4GWSS
4 gas burners, grill and griddle
ZDP48N6RWSS
6 gas burners and grill
ZDP48N6DWSS
6 gas burners and griddle
48" Liquid Propane Gas Models:
ZDP48L4GWSS
4 gas burners, grill and griddle
ZDP48L6RWSS
6 gas burners and grill
ZDP48L6DWSS
6 gas burners and griddle
36" Natural Gas Models:
ZDP36N6WSS
6 gas burners
ZDP36N4RWSS
4 gas burners and grill
ZDP36N4DWSS
4 gas burners and griddle
36" Liquid Propane Gas Models:
ZDP36L6WSS
6 gas burners, grill and griddle
ZDP36L4RWSS
4 gas burners and grill
ZDP36L4DWSS
4 gas burners and griddle
Accessory
Requirements
All models require the installation of a
backguard. A backguard should be ordered at
the same time as the range. Both must be on
site at the time of installation.
Order one backguard for 48" Models:
ZX1B48WSS
1-1/2" high backguard (required for island
installations)
ZX12B48WSS
12" high backguard
ZX22B48WSS
22" high backguard with warming rack
(2 piece)
Order one backguard for 36" Models:
ZX1B36WSS
1-1/2" high backguard for island installations
only
ZX12B36WSS
12" high backguard
ZX22B36WSS
22" high backguard with warming rack
22" High Backguard With
Warming Shelf
12" High Backguard
1-1/2" Backguard for
Island Installations only
3
Product
Design Information
Professional Ranges
Dimensions
& Clearances
35-1/4"-36-3/4"
28-1/4"
Optional Backguards
36" Wide Range Models
21-1/4"
12"
1-1/2"
35-7/8"
35-1/4"-36-3/4"
28-1/4"
Optional Backguards
48" Wide Range Models
21-1/4"
12"
1-1/2"
47-7/8"
4
Loading...