Monogram ZDWT240, ZDBT240 Installation Instructions Manual

Installation
Instructions

If you have questions, call 800.626.2000 or visit our website at: www.monogram.com

Wine Reserve

ZDWT240
and

Beverage Center

ZDBT240

Design Guide
With Installation Instructions

Safety Information

BEFORE YOU BEGIN:

Read these instructions completely and carefully.

IMPORTANT – Save these instructions

for local inspector’s use.

IMPORTANT – Observe all governing

codes and ordinances.

Note to Installer – Be sure to leave these

instructions with the Consumer.

Note to Consumer – Keep these instructions with

your Owner’s Manual for future reference.

WARNING – This appliance must be

properly grounded. See “Grounding”, page 4.

AVERTISSEMENT –

Cet appareil doit être correctement mise à la terre.
Consulter <<Mise à la terre>>, page 4.

If you received a damaged wine reserve or beverage
center, you should immediately contact your dealer
or builder.

Skill Level – Installation requires basic mechanical

skills. Proper installation is the responsibility of the
installer. Product failure due to improper installation
is not covered under the GE Appliance Warranty.

WARNINGS:

• Use this appliance only for its intended purpose.

• Immediately repair or replace electrical service
cords that become frayed or damaged.

• Unplug the unit before cleaning or making repairs.

• Repairs should be made by a qualified service
technician.

AVERTISSEMENT :

• Il ne faut utiliser cet appareil que pour l’usage
pour lequel il a été construit.

• Il faut réparer ou remplacer immédiatement tout
cordon d’alimentation électrique effiloché ou
endommagé.

• Débrancher le bar ou le réfrigérateur a vin avant
le nettoyage ou toute intervention.

• Les réparations doivent être faites par un
technicien qualifié.

For Monogram local service in your area, call

1.800.444.1845

For Monogram service in Canada, call

1.888.880.3030

For Monogram Parts and Accessories, call

1.800.626.2002.

www. monogram.com

CONTENTS

Design Guide

The Installation Space ............................3

Product Clearances ................................ 3

Installation Instructions

Tools, Hardware ....................................... 4

Grounding the Product ........................... 4

Staining Wood Drawer Fronts ...............4

Step 1, Remove Packaging .................... 4

Step 2, Leveling ........................................5

2

Step 3, Connect Power ........................... 5

Step 4, Slide Product into Cutout .......... 5

Step 5, Change the Toekick .................... 5

Step 6, Set Temperature Controls .........5

Design Guide

21-5/8"

23-5/8"

4" Minimum

to Wall

90°

THE INSTALLATION SPACE

Locate
Outlet

10-1/2"

24"

9" Max.

34-1/2"-35"

NOTE:

Handle and
handle standoff
depth is 1-3/4″

The cutout depth should be 24″

The cutout dimensions shown allow for a full door
swing and access to the pull-out racks when installed
as a built-in in standard 24″ deep cabinets.

• The wine reserve and beverage center can be
installed freestanding.

• If installing between frameless cabinets, a 1/2″ wide
filler strip or side panel may be needed on hinge
side. The filler strip will act as a spacer between the
case and adjacent cabinet door swing. The width
of the opening must include the filler panels.
NOTE: The door should protrude 1″ beyond the
surrounding cabinets.

1-1/2"

23-3/4" Min.

23-3/4"

34-1/2"

23-3/4"

PRODUCT CLEARANCES

The wine reserve and beverage center is factory set
for a 110° door swing.

When installed in a corner:

• Allow 4″ min. clearance on the hinge side for the
90° door swing and to allow racks to slide out.

• Allow 10″ minimum clearance on the hinge side
for a full 110° door swing.

10" Minimum

to Wall

110°

Choose the location:

• These products may be closed in on the top and
three sides as long as the front is unobstructed for
air circulation and proper access to the door.

• Do not install these products where the temperature
will go below 55°F (13°C) or above 90°F (32°C).

• Do not install where it will be subject to direct
sunlight, heat or moisture.

• These products are not designed to be stacked one
over the other.

90° Door Swing

Additional Specifications

• A 120 volt 60Hz., 15 or 20 amp power supply is
required. An individual properly grounded branch
circuit or circuit breaker is recommended. Install a
properly grounded 3-prong electrical receptacle
recessed into the back wall as shown. Electrical must
be located on rear wall as shown. NOTE: GFI
(ground fault interrupter) is not recommended.

SIDE-BY-SIDE INSTALLATIONS

Increase storage capacity by installing two Monogram
beverage centers or wine reserves together. Or, for a
complete refreshment center, install any two of these
units together.

• A side-by-side installation requires at least a 47-1/2″
wide opening. No trim kits required.

• Products must operate from separate, properly
grounded receptacles.

Black or Stainless Steel Toekick Options

• These products are shipped with a black toekick
installed. An optional stainless steel toekick is also
supplied with each product. For shipping purposes,
the stainless steel toekick is secured to the back
or inside the unit.

Locate

Outlet

34-1/2"-35"

10-1/2"

15"

47-1/2" Min.

9"

14"

10-1/2"

9"

1-1/2"

3

24"