Monogram WX08X10002, WX08X10006, WX08X10015, WX08X10025, ZIPP360NHSS Design And Installation Manual

Download

Design Guide with

Installation Instructions

36” Built-In French Door, Bottom-Freezer Refrigerators

Pub. No. 49-60700 Part No. 224D3560P001

12-13 GE

monogram.com

Safety Information

BEFORE YOU BEGIN

Read these instructions completely and carefully.

• IMPORTANT — Save these instructions

for local inspector’s use. Observe all governing codes and ordinances.

• Note to Installer — Be sure to leave these

instructions with the Consumer.

• Note to Consumer — Keep these instructions

with your Owner’s Manual for future reference.

WARNING:

This appliance must be properly grounded. See

“Grounding the Refrigerator,” page 9.

AVERTISSEMENT

Cet appareil doit être correctement mis à la terre. Consulter « Mise à la terre du réfrigérateur », page 9.

If you received a damaged refrigerator, you should immediately contact your dealer or builder.

CAUTION:

Due to the weight and size of this refrigerator, and to reduce the risk of personal injury or damage to the

product—THREE PEOPLE ARE REQUIRED FOR PROPER INSTALLATION.

PRUDENCE

À cause du poids et de la taille de ce réfrigérator et pour réduire le risque de blessure et de dommages, IL FAUT TROIS PERSONNES POUR FAIRE L’INSTALLATION CORRECTEMENT.

Skill Level — Installation of this refrigerator requires

basic mechanical, carpentry and plumbing skills. Proper installation is the responsibility of the installer. Product failure due to improper installation is not covered under the GE Appliance Warranty. See the Owner’s Manual for warranty information.

WARNING:

• These refrigerators are top-heavy and must

be secured to prevent the possibility of tipping

forward. Anti-Tip protection is required. See page 11

for details.

• Use this appliance only for its intended purpose.

• Immediately repair or replace electric service cords

that become frayed or damaged.

• Unplug the refrigerator before cleaning or making

repairs.

• Repairs should be made by a qualified service

technician.

AVERTISSEMENT

• Ces réfrigérateurs sont lourds en haut et il faut les arrimer pour éviter leur basculement. Il faut avoir

un système de protection contre le renversement.

Voir les détails page 11.

• Il ne faut utiliser cet appareil que pour l’utilisation appropriée.

• Réparer ou remplacer immédiatement tout cordon électrique effiloché ou endommagé.

• Il faut débrancher le réfrigérateur avant le nettoyage

ou toute intervention.

• Les réparations doivent être faites par un technicien qualifié.

For Monogram local service in your area, call

1.800.444.1845.

For Monogram service in Canada, call

1.800.561.3344

For Monogram Parts and Accessories, call

1.800.626.2002.

www. monogram.com

CONTENTS

Planning Guide

The Installation Space .............................. 3

Dimensions and Clearances ................. 3

130° Door Swing ......................................... 4

90° Door Swing ............................................5

Customization Basics ............................... 6

Panel Dimensions .......................................7

Side Panels .................................................... 8

Installation Instructions

Tools, Hardware, Materials .................... 9

Grounding the Refrigerator ................... 9

Step 1, Remove Packaging ................. 10

Step 2, Install Water Line ..................... 10

Step 2A, RO Water Line ........................ 11

Step 3, Install Side Panels .................... 11

Step 4, Install Anti-Tip Brackets ........ 11

Step 5, Level Refrigerator .................... 12

Step 6, Alternate Anti-Tip Procedure... 12 Step 7, Secure Refrigerator to

Cabinetry ..................................... 12

Step 8, Adjust Door Swing ................... 13

Step 9, Install Grille Panel .................... 13

Step 10, Install Framed Panels ......... 14

Step 10A, Install Overlay Panels ....... 15

Step 11, Connect Water Supply ....... 16

Step 12, Connect Power ....................... 16

Step 13, Start Icemaker ........................ 16

Step 14, Install Toekick ......................... 17

*83 1/2"

25-3/8" Framed Models 25-3/4" Stainless Steel Models

Pro Models)

Bottom

35-1/2"

12-1/8"

Design Guide

THE INSTALLATION SPACE

Finished Width

10"

Wall View

75" From

Floor to

of Electrical Ar

The finished

2-5/16"

cutout width must be 35-1/2”.

85" Finished Opening

Electrical

10"

24" Cutout Depth

10"

Area

Water Supply

3-1/2"

Water And Electrical Locations

Electrical and water supply must be located as shown.

The cutout depth must be 24”

The refrigerator will project forward, slightly beyond

adjacent cabinetry, depending on your installation. Allow minimum 1/8” air gap between case back & wall.

Cutout depth beneath a soffit:

When installed beneath a soffit, the soffit cannot exceed the 24” installation depth shown. The top case trim overlaps the bottom of the soffit.

DIMENSIONS AND CLEARANCES

35"

Case Width

Rear

Depth Including Handles:

27" Framed Models 27-13/16" Stainless Steel Models 28-5/8" Professional Style Models

Product Clearances

These refrigerators are equipped with a 2-position door stop. The factory set 130° door swing can be adjusted to

90° if clearance to adjacent cabinets or walls is restricted.

Min. to

Wall

Case Depth

*84" From Floor to Top Frame

36" Frame to Frame Width

Min. to

Wall

* Shipping height. The

refrigerator can be adjusted to fit into a cutout that is 83-1/2” min. to 84-1/2” max. height. Note that the top case trim at the front is 1/2” higher and will overlap upper cabinetry

or soffit. Use leveling

legs and wheels for a maximum 1” height adjustment.

23-7/8"

Behind Frame

Additional Specifications

• A 115 volt 60Hz., 15 or 20 amp power supply is required.

An individual properly grounded branch circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle recessed into the back wall. Electrical must be located on rear wall as shown.

Note: GFI (ground fault interrupter) is not recommended.

• Water line can enter the opening through the floor or back wall. Route GE SmartConnect™ kit or 1/4” O.D.

copper tubing between the cold water line and the water connection location. The tubing should be long enough to extend to the front of the refrigerator. Installation of an easily accessible shut-off valve in the water line is required.

(Stainless

18-1/8"

130°

90°90°

*4” Stainless and Framed Models. 5” Pro Series

*Min. Distance to Wall

18-3/16”

(Framed Models)

Allow 12-1/8” minimum clearance for a full 130° door swing.

For a 90° door swing, allow 4” min. clearance to a wall, for framed and stainless steel models. Allow 5” min. clearance for professional style models. If the 90° door stop position is used, pan access is maintained, but pan removal is restricted.

See illustrations pages 4 and 5 to determine door swing interaction with adjacent cabinets or countertops.

Refrigerator

Design Guide

23-7/8" From

Rear of

Refrigerator

Frameless Cabinets: The case trim overlaps cabinets at the top and sides.

Therefore, frameless cabinets

may require filler strips to prevent interference with cabinet door swing.

The opening must allow for filler strips.

Case

Trim

Door

1/4"

1/2"

3/4"

1-1/4"

1-3/4"

1-1/2"

Stainless Steel

1/4"

2-1/2"

2-1/4"

3/4" Overlay

(Nominal Size)

1/2"

2-3/4"

Panel

3/4"

1/4"

1/2"

3/4"

1-1/4"

Top View 130° DOOR SWING (factory setting) Scale 1:1

Refrigerator

Design Guide

Case Trim

Frameless Cabinets:

The case trim overlaps

cabinets at the top and sides. Therefore, frameless cabinets may require filler strips to prevent interference with cabinet

door swing. The opening

must allow for filler strips.

23-7/8"

From Rear of

Refrigerator

1/4"

Door

1/4"

1/2"

3/4"

1-1/4"

1-1/2"

Stainless Steel

3/4" Overlay

Panel

(Nominal Size)

1/2"

Top View 90° DOOR SWING (optional setting) Scale 1:1

3/4"

1-1/4"

Design Guide

CUSTOMIZATION BASICS:

Framed Or Overlay Panels, Custom Handles and Accessory Kits

Professional Style Stainless Steel Refrigerators

Stainless steel wrapped refrigerators with beveled edges

and professional style handles. These models are shipped

ready for installation.

Stainless Steel Wrapped Refrigerators

Stainless steel wrapped refrigerators with beveled edges and tubular stainless steel handles that coordinate with

other Monogram appliances. These models are shipped

ready for installation.

Trimmed Refrigerators

Trimmed refrigerators are designed to be customized with

decorative panels. Field installed custom door and grille panels are required.

Framed panels

You may install 1/4” thick custom panels from your

cabinet manufacturer. The decorative panel slides into the

factory installed trim.

Overlay panels

You may also choose to install custom overlay panels from your cabinet manufacturer. This design provides a seamless appearance which integrates smoothly with surrounding cabinetry.

3/4" Overlay Panel

.10" Thick Spacer Panel

1/4" Thick Backer Panel

Standard supplied handles shown in 3/4” overlay panel position.

Door and Drawer Handles

The standard supplied handles can be adjusted to accommodate both framed or overlay panels. Custom

handles of your choice, supplied by your cabinet maker can also be installed on overlay panels.

Standard Door Handles

Framed Panel

Standard Door Handles

Standard supplied handles shown in 1/4” panel position.

Optional Accessory Kit

• ZKHPSS1: Professional Tubular Stainless Steel Handle

designed to fit 3/4” overlay panels. Kit includes one handle. Order 3 kits for bottom-freezer refrigerators from your Monogram supplier.

Side Panels

Side panels must be used whenever the sides of the refrigerator will be exposed.

Design Guide

1/4” FRAMED PANEL DIMENSIONS

If you choose to install framed panels, they must be cut

to the dimensions shown. The panels will slide into the

frame on the door, drawer and grille.

If the custom panel is less than 1/4” thick and if it fits loosely in the door frame, it can be backed up with a piece of filler material or foam tape to improve the fit.

Framed Panel Dimensions

A (Width) B (Grille Height) C (FF Height) D (FZ Height) E (FF Width)

1/4” Framed Panel 33-7/8” 8-7/8” 46-1/16” 21-7/8” 16-3/8”

5/16"

Door

IMPORTANT NOTE: Maximum total panel weight:

• Fresh food door panel – 30 lbs.

• Freezer drawer panel – 28 lbs.

• Grille Panel – 11 lbs.

Trim

Reveal

1/4"

Panel

Overlay Panel Dimensions

A (Width) B (Grille Height) C (FF Height) D (FZ Height) E (FF Width)

1/4” Backer Panel 33-7/8” 8-7/8” 46-1/16” 21-7/8” 16-3/8”

0.10” Spacer Panel 32-1/2” 7-5/8” 44-11/16” 20-1/2” 15”” 3/4” Overlay Panel 34-1/8” 9” 46-5/16” 22” 16-5/8”

3/4” OVERLAY PANEL DIMENSIONS

For a more custom appearance, overlay panels may be

installed on trimmed models. The overlay panel must be

secured to a 1/4” thick backer panel which slides into the trim. A spacer panel 0.10” thick must be placed between the overlay and backer panel.

Assemble the panels with glue and screws.

• Center the spacer panel on the backer panel, left to

right and top to bottom. Secure the panels with glue.

• Center the spacer and backer panel on the overlay

panel and secure with glue and screws. Screws must be countersunk into the backer panel.

Overlay Panel

Spacer Panel

Backer Panel

IMPORTANT NOTE: Maximum total weight for the assembled panels:

• Fresh food door panel – 30 lbs.

• Freezer drawer panel – 28 lbs.

• Grille Panel – 11 lbs.

NOTE: Left-to-right offset is not always equal to

top-to-bottom offset.

Design Guide

SIDE PANELS

Side panels must be used whenever the sides of the refrigerator will be exposed. The 1/4” side panels will slip into the side case trim. Secure the panels to the refrigerator with stick-on hook and loop fastener strips. Order the side panels from the cabinet manufacturer.

• Cut a notch in the top front corner as shown to allow

clearance for corner keys in the front side trim.

* Depending on

installation height.

24"

3/16"

1-7/8"

*84"

*3" to 4"

2-9/16"

Installation Instructions

TOOLS REQUIRED

• Tinsnips to cut banding

• Stepladder

• Bucket

• Level

• Appliance Hand Truck

• Tubing cutter

• 7/16” open-end wrench

• #2 Phillips screwdriver

• Drill and appropriate bits

• 5/16”, 7/16” socket

• Safety glasses

• 1-1/4” open end wrench

• Pliers

• 1/4” ratchet

HARDWARE SUPPLIED

• Water filter bypass plug

• Anti-Tip brackets

• 1/4” nut and ferrule

MATERIALS REQUIRED

• 35” long 2x4 for Anti-Tip support

• 1/4” copper water line tubing or GE SmartConnect™ Refrigerator Tubing kits

• Water shut-off valve

• Custom panels for fresh food door, freezer drawer

and grille panel

• Screws to secure refrigerator to cabinetry.

• Stick-on hook and loop fastener strips for

1/4” side panels

FLOORING

For proper installation, this refrigerator must be placed on a level surface of hard material that is at the same

height as the rest of the flooring. This surface should

be strong enough to support a fully loaded refrigerator, or approximately 1,200 lbs.

NOTE: Protect the finish of the flooring. Cut a large

section of the cardboard carton and place under the refrigerator where you are working.

GROUNDING THE REFRIGERATOR

IMPORTANT—(Please read carefully)

FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE PROPERLY GROUNDED.

The power cord of this appliance is equipped with a 3-prong (grounding) plug which mates with a standard three-prong (grounding) wall receptacle to minimize the possibility of electric shock hazard from this appliance.

Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly grounded.

Where a standard 2-prong wall outlet is encountered, it is your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet.

DO NOT, UNDER ANY CIRCUMSTANCES, CUT OR REMOVE THE THIRD (GROUND) PRONG FROM THE POWER CORD.

DO NOT USE AN ADAPTER PLUG TO CONNECT THE REFRIGERATOR TO A 2-PRONG OUTLET.

DO NOT USE AN EXTENSION CORD WITH THIS APPLIANCE.

Installation Instructions

STEP 1 REMOVE PACKAGING

CAUTION: Refrigerator is much heavier at the

top than at the bottom—be careful when moving. When

using a hand truck, handle from side only.

PRUDENCE: Le réfrigérateur est beaucoup

plus lourd en haut qu’en bas. Il faut être prudent lors des déplacements. Si un diable est utilisé, il faut soulever le réfrigérateur sur le côté seulement.

• Carefully cut banding at the top and bottom,

remove outer carton.

• Slide out back corner posts (2).

• Slide carton off top of cabinet. NOTE: IT IS NOT NECESSARY TO LAY CABINET DOWN IN ORDER TO REMOVE SKID!

• The unit is secured to the skid with 2 full-length

tie-down straps. Remove the ten 5/16” bolts from the base channels in the tie-downs.

STEP 2 INSTALL WATER LINE

• Remove the four 7/16”

bolts securing the straps to the skid.

CAUTION: DO NOT

Remove 5 base channel bolts on each side

Remove 2 strap bolts on each side

• Support blocks on the bottom of the refrigeration

case must be removed before the refrigerator is taken off the skid or damage will occur. Carefully, tilt refrigerator and slide blocks out from beneath.

• Remove toekick. Set aside for final installation.

• Lift the refrigerator off the skid with an appliance dolly. Handle from the sides.

ATTEMPT TO ROLL UNIT

OFF SKID.

PRUDENCE: IL NE

FAUT PAS ESSAYER DE FAIRE ROULER LE RÉFRIGÉRATEUR POUR L’ENLEVER DE LAY PALETTE.

• A cold water supply is required for automatic icemaker operation. The water pressure must be

between 40 and 120 p.s.i.

• Route 1/4” OD copper or GE SmartConnect™ plastic

tubing between house cold water line and the water connection location.

• Tubing should be long enough to extend to the front of

the refrigerator. Allow enough tubing to accommodate bend leading into the water line connection.

NOTE: The only GE-approved plastic tubing is supplied in the GE SmartConnect™ Refrigerator Tubing kits. Do not

use any other plastic water supply line because the line is under pressure at all times. Other types of plastic may crack or rupture with age and cause water damage to your home.

GE SmartConnect™ Refrigerator Tubing Kits are available

in the following lengths:

2 ft (.6 m) WX08X10002 6 ft (1.8 m) WX08X10006 15 ft (4.6 m) WX08X10015 25 ft (7.6 m) WX08X10025

Shut off the main water supply.

Turn on the nearest faucet long enough to clear the line

of water.

• Install a shut-off valve between the icemaker water

valve and cold water pipe in a basement or cabinet.

The shut-off valve should be located where it will be

easily accessible.

Floor

Waterline Tubing

• Turn on the main water supply and flush debris.

Run about a quart of water through the tubing into a bucket. Shut off water supply at the shut-off valve.

NOTE: Saddle type shut-off valves are included in many water supply kits, but are not recommended for this application.

NOTE: Commonwealth of Massachusetts Plumbing Codes 248CMR shall be adhered to. Saddle valves

are illegal and use is not permitted in Massachusetts.

Consult with your licensed plumber.

Installation Instructions

STEP 2A

WATER LINE INSTALLATION WITH A REVERSE OSMOSIS SYSTEM

Skip this step when not using an RO System

If the water supply to the refrigerator is from a Reverse Osmosis Water System, use the refrigerator’s filter bypass

plug. Using the refrigerator’s water filtration cartridge with

the RO filter can result in hollow ice cubes.

Filter Bypass Plug

STEP 3

Skip this step when not using side panels If you are using 1/4” side panels, they should be inserted into the case trim. Fasten the panels to the refrigerator with stick-on hook and loop fastener strips before setting refrigerator in place.

INSTALL SIDE PANELS

STEP 4

INSTALL ANTI-TIP BRACKETS

WARNING: ANTI-TIP PRECAUTIONS

The refrigerator is top-heavy and must be secured to prevent the

possibility of tipping forward.

ATTENTION: PRECAUTIONS CONTRE LES

BASCULEMENTS Le réfrigérateur est beaucoup plus lourd en haut et il faut le maintenir en place pour éviter la possibilité de son basculement

vers l’avant.

• Cut a 2” x 4” x 35” block and secure the block to the mounting brackets provided using #12 or #14 wood screws.

• Secure the bracket with wood block to the back wall so that it is

84” (or your installation height) from the finished floor. Use #12

or #14 wood screws. See illustration.

• Screws must penetrate at least one inch into vertical wall studs.

• Before pushing the refrigerator into the opening, plug the power

cord into the receptacle. Open the grille panel and reach into the opening at the back to grasp the power cord. Pull the power cord into the opening as you push the refrigerator back.

• Gently push refrigerator into the opening with hands against

front corners.

Important Note: When the refrigerator is installed under a soffit or if there is not enough height for this method of security, brackets cannot be used. Proceed to step 5 to level the refrigerator and then to step 6

to secure refrigerator to cabinets. The refrigerator must be secured to

prevent tipping.

Installation Instructions

STEP 5 LEVEL REFRIGERATOR

All models have 4-point leveling. The front is supported

by leveling legs, the rear is supported by adjustable wheels. Both are accessible from the front of the refrigerator.

• To level the back of the refrigerator, turn the 7/16” hex nut located above the front wheels. Turn clockwise to

raise or counterclockwise to lower the refrigerator.

• For front leveling, use a 1-1/4” open-end wrench.

• Adjust height of refrigerator to match installation

cutout opening 83-1/2 to 84-1/2”. The refrigerator should be level and plumb with cabinetry.

STEP 6 ALTERNATE ANTI-TIP

PROCEDURE

The refrigerator must be secured to prevent tipping. The anti-tip brackets cannot be used on metal wall

studs. Use this Alternate Procedure to secure the refrigerator against tip-over whenever metal wall studs are encountered and there is no soffit.

CAUTION:

The rear leveling wheels and front leveling legs are

limited to a maximum height adjustment of 1”. If the installation requires more than 84-1/2” height, the installer should elevate the refrigerator on a sheet

of plywood or runners. Cabinetry trim could also be

added across the top of the opening to shorten the opening. If you attempt to raise the refrigerator more than 1”, you will damage the front leveling legs and the rear leveling wheels.

PRUDENCE

Les roues de nivellement arrière et les pattes de nivellement avant permettent un réglage maximal de 25 mm (1 po). Si l’ouverture pour le réfrigérateur a une hauteur supérieure à 2,15 m (84-1/2 po), l’installateur doit élever le réfrigérateur sur une feuille de contre-plaqué ou des glissières. Il est également

possible d’ajouter des baguettes de finition des

placards sur le haut de l’ouverture afin de la réduire. Lever le réfrigérateur de plus de 25 mm (1 po)

endommage les pattes de nivellement avant et les roues de nivellement arrière.

• Raise the grille panel to access case trim.

• Use a 3/16” bit to drill four evenly spaced clearance

holes through the metal top case trim.

• Use a 1/16” bit to drill to pilot holes through the metal clearance holes and into the wood soffit. The holes

should be centered in the soffit or a 3/4” min. wood

brace. The brace spanning the enclosure must be

securely fastened to cabinets on both sides.

• Install four, 1-1/2” drywall screws into the pilot holes.

STEP 7 SECURE REFRIGERATOR

TO CABINETRY

Whenever possible, perform this step for anti-tip security, or when anti-tip brackets cannot be used.

The refrigerator must be secured to prevent tipping.

• Raise the grille panel to access case trim.

• Drill hole in trim and drive screw through the trim into

adjacent cabinet.

• Follow the same procedure on the opposite side.

Drive screws through case trim and into adjacent cabinets.

Installation Instructions

STEP 8 ADJUST DOOR SWING

NOTE: This refrigerator has a 2-position door stop.

When space does not allow the door to swing open fully to 130°, you may change the door swing to a 90° opening. Skip this step if door opening is satisfactory

for your installation situation.

• Lift the grille panel to access the wire cover trim.

• Remove screws on both sides of the wire cover trim

and rotate off.

• Use pliers to unscrew door stop and reinstall into the

90° position.

Remove wire cover

trim screws

STEP 9 INSTALL GRILLE PANEL

• Raise the grille panel to stop position.

Loosen

Side

Trim

Screw

• Loose screws on side trim behind frame. Remove

bottom trim.

• Slide panel over the metal backer panel and into

the trim.

• If necessary, tap with a wood block until panel slips

under the top trim piece.

• Reassemble bottom trim. Tighten screws.

• Adjust the hinge spring to accommodate the panel

weight, if necessary.

Raise Grill Panel

Adjust Nut Below Spring to Accommodate Panel Weight

Loosen

Side

Trim

Screw

• Reinstall the wire cover trim.

Installation Instructions

STEP 10 INSTALL 1/4” FRAMED PANELS

Standard supplied handle shown

in 1/4” panel position.

IF YOU ARE INSTALLING OVERLAY PANELS, GO TO STEP 10A.

Install door and drawer panels:

• Open door to 90°. Remove the 4 Phillips head screws

from the door handle.

• Remove handle. Retain all screws.

• Remove 4 screws holding trim, lift off trim.

Retain screws.

• Slide framed panel into the door trim.

• There are two sets of holes in the handle side trim.

Replace handle side trim by installing the original screws

in the FRONT screw holes.

• Secure the handle to the door using the REAR

screw holes.

• Follow the same procedures to install the second door

panel and the drawer panel.

to Secure Trim

to Secure Handle

Installation Instructions

STEP 10A INSTALL OVERLAY PANELS

Use Front Holes

Use Rear Holes

Supplied handle shown in the

overlay panel position.

Install door and drawer panels:

• Open door to 90°. Remove the 4 Phillips head screws

from the door handle.

• Remove handle. Retain all screws.

• Remove 4 screws holding trim, lift off trim.

Retain screws.

• Slide overlay panel into the door trim.

Right hand models shown. Use the same instructions for left hand models.

• There are two sets of holes in the handle side trim.

Replace handle side trim by installing the original screws in the REAR screw holes.

• Secure the handle to the door using the FRONT

screw holes.

• Follow the same procedures to install the second door

panel and the drawer panel.

Custom handles

If you are using custom handles, the handle must be properly secured to the panel before sliding the panel into the trim.

• The cabinet manufacturer will supply the custom

handle and hardware.

• Secure the door/drawer trim using both the FRONT

and REAR screw holes. Discard supplied handle.

OFF

Installation Instructions

STEP 11 CONNECT WATER SUPPLY

House

Water Supply

• Locate and bring tubing to the front of the cabinet.

• Turn the water on to flush debris from line. Run about

a quart of water through tubing into a bucket, then shut off water.

Copper Tubing:

• Slip a 1/4” nut and ferrule (provided) over both ends

of the copper tubing. Insert tube into the union fitting on the unit and tighten nut to union.

• Turn on the water to check for leaks.

Refrigerator

Water Supply

STEP 12 CONNECT POWER

• Check to be sure the power cord is plugged into the

receptacle.

Raise Grille

Electrical Outlet

Master

Light Switch

Panel

• Check to make sure power to refrigerator is on by

opening refrigerator door to see if interior lights are on.

• The temperature controls are preset at 37°F for the fresh food section and 0°F for the freezer.

• Allow 24 hours to stabilize before making

adjustments.

STEP 13 START ICEMAKER

GE SmartConnect™ Tubing:

• Insert the molded end of the tubing into the refrigerator connection. Tighten the compression nut

until it is just hand tight.

• Tighten one additional turn with a wrench. Overtightening can cause leaks!

• Turn on the water to check for leaks.

Note: Make sure excess tubing length does not interfere with drawer closing or toekick installation.

• Flip the switch to I (ON). The icemaker will begin

operation automatically.

• Be sure nothing interferes with the sweep of

the feeler arm.

• Discard the first full bucket of ice cubes.

• To turn the icemaker off, set the switch to O (OFF).

Installation Instructions

STEP 14 INSTALL TOEKICK

• Locate the supplied toekick (shipped taped to the side of the refrigerator). Install the toekick assembly with the 3 screws provided, adjust to the desired height and tighten the screws.

• A custom toekick can be installed to match or complement the surrounding cabinetry. Use the

supplied toekick as a template to cut the shape.

IMPORTANT: The gap between the bottom of the

refrigerator cabinet and the top of the toekick must remain unobstructed for proper air circulation.

INSPECT FINAL INSTALLATION

Check door alignment

Stand back away from the refrigerator to inspect the final installation.

• Installation or the addition of heavy door panels

may have caused the doors to move slightly out of

alignment. Check to be sure the top of the doors are

evenly aligned with each other. If necessary, the doors may be adjusted up or down to align.

• Add or subtract shims as shown to adjust the right

door only. More shims are located under the hood on the left side in the bag with the filter bypass plug and mini manual.

To Raise Right Hand Door

• Lift the right hand door up so there is a gap below the

bottom hinge bushing.

• Snap a shim onto the hinge pin below the bushing.

• Lower the door and re-check the alignment.

• Repeat as necessary.

To Lower Right Hand Door

• Lift the right hand door up so there is a gap below the

bottom hinge bushing.

• Remove a shim by pushing shim off of the hinge pin.

• Lower the door and re-check the alignment.

• Repeat as necessary.

Bag location

Shim

Notes

NOTE: While performing installations described in this book, safety glasses or goggles should be worn.

For Monogram® local service in your area, call

1.800.444.1845.

NOTE: Product improvement is a continuing endeavor

at General Electric. Therefore, materials, appearance and

specifications are subject to change without notice.

Pub. No. 49-60700 Part No. 224D3560P001

12-13 GE

GE Consumer & Industrial

Appliances General Electric Company Louisville, KY 40225 monogram.com

GEAppliances.com

Monogram WX08X10002, WX08X10006, WX08X10015, WX08X10025, ZIPP360NHSS Design And Installation Manual

Specifications and Main Features

Frequently Asked Questions

User Manual