Monogram MORERADWRH3038 Specs

ZV48SSJSS – Monogram 48" Stainless Steel Professional Hood

47 15/16"

12"

18"

47 15/16"25"

Soffit

Soffit Installation

30" min

36" max

Wall Mount Installation

30" min

36" max

Dimensions and Specifications (in inches)

Installation Clearances

These vent hoods are designed to be installed onto a wall
or beneath a soffit or cabinet.

• Install these hoods* 30" min. to 36" max. above the

cooking surface.

* These hoods may be installed 24" min. above a gas or

electric drop-in style cooktop. Always observe the 30" to
36" clearance when installed over any professional style

cooktop or range.

Note: Clearances may vary due to type of cooking product
and local codes. Check with local inspectors to be sure
standard is applicable.

Soffit Installation

In this installation, the ductwork running from the top of the

hood will be concealed in the soffit or upper cabinetry.

Wall Mount Installation

For this installation, a decorative duct cover is available to conceal
the ductwork running from the top of the hood. Use of the duct cover
requires special consideration to the installation height above the
countertop.

Listed by
Underwriters
Laboratories

For answers to your Monogram, GE Profile™
Series or GE® Series appliance questions, visit
our website at GEAppliances.com or call
GE Answer Center® service, 800.626.2000.

Specification Revised 1/16

ZV48SSJSS – Monogram 48" Stainless Steel Professional Hood

Optional Duct Cover Accessories

6" Duct Cover

12" Duct Cover

Advanced Planning

Ductwork Planning

• These vent hoods are equipped for 10" round ductwork. In most
instances they may be transitioned to 8" round.

• T his hood may be vented vertically through upper cabinets, soffit or

ceiling. A duct transition piece is supplied for vertical exhaust. Use
locally supplied elbows to vent horizontally through the rear wall.

• Determine the exact location of the vent hood.

• Plan the route for venting exhaust to the outdoors.

• Use the shortest and straightest duct route possible. For
satisfactory performance, duct run should not exceed 150 ft.

equivalent length for any duct configurations.

• Refer to “Duct Fittings” chart to compute the maximum permissible

length for duct runs to the outdoors.

• Use metal ductwork only.

• Install a wall cap or roof cap with damper at the exterior opening.

Order the wall or roof cap and any transition needed in advance.

Wall Framing for Adequate Support

• These vent hoods are heavy. Adequate structural support must
be provided. Hoods must be secured to vertical studs in the wall.

• It is strongly recommended that the vent hood with duct cover
be on site before final framing and wall finishing. This will also
help to accurately locate the ductwork and electrical service.

Decorative Duct Covers:

Decorative duct covers, 6" and 12" high, are available to fit all
models. The duct cover conceals the ductwork running from
the top of the hood to the ceiling or soffit. Stack one or more
duct covers over the top of the hood to reach your ceiling height.

POWER SUPPLY

IMPORTANT – (Please read carefully)

WARNING: FOR PERSONAL SAFETY, THIS APPLIANCE MUST

BE PROPERLY GROUNDED.
Remove house fuse or open circuit breaker before beginning

installation.

Do not use an extension cord or adapter plug with this appliance.

Follow national electrical codes or prevailing local codes and
ordinances.

Electric supply

These vent hoods must be supplied with 120V, 60Hz, and connected

to an individual, properly grounded branch circuit, and protected

by a 15 or 20 amp circuit breaker or time delay fuse.

• Wiring must be 2 wire with ground.

• If the electrical supply does not meet the above requirements,

call a licensed electrician before proceeding.

• Route house wiring as close to the installation location as possible

on the back wall or ceiling.

• Connect the wiring to the house wiring in accordance with
local codes.

Grounding instructions

The grounding conductor must be connected to a ground metal,
permanent wiring system, or an equipment-grounded terminal
or lead on the hood.

WARNING: The improper connection of the equipment-

grounding conductor can result in a risk of electric shock. Check
with a qualified electrician or service representative if you are in
doubt whether the appliance is properly grounded.

Optional Duct Cover Accessories

Decorative duct covers are available in 6" and 12" heights. Duct

covers may be stacked, in various combinations, to conceal the
ductwork running from the top of the hood to the ceiling.

• Before you begin, you should determine the installation height

of the hood and order the correct size duct cover. The duct
covers should be ordered at the same time as the vent hood
and be on site before installation. Order the duct cover
corresponding to your model.

6" Duct Covers
Hood Model 6" Duct Cover Dimensions

ZV48SSJSS ZX48DC6J 6"H x 19-11/16"W x 11-7/8"D

12" Duct Covers
Hood Model 12" Duct Cover Dimensions

ZV48SSJSS ZX48DC12J 12"H x 19-11/16"W x 11-7/8"D

Listed by
Underwriters
Laboratories

For answers to your Monogram, GE Profile™
Series or GE® Series appliance questions, visit
our website at GEAppliances.com or call
GE Answer Center® service, 800.626.2000.

Specification Revised 1/16