Monitor Audio BRW-10 User Manual

Contents
Page Introduction 2 Safety Instructions 3-4 Recycling(WEEE) 4 RoHSStatement 4 FootFixing 5 AmplifierPanelandControls 6-8 Positioning&SetUp 9 Specification 10 GuaranteeandService 11 Claims underthisguarantee 11 EC DeclarationofConformity 12 Data Protection 13 OwnerInformation 13 WarrantyCard–Foldoutsectioninbackcover
© Monitor Audio 200 6 BRW-10 Rev4
1
Introduction
Thank you for your purchase of Monitor Audio Bronze BRW-10 subwoofer, which has been designed and constructed using quality systems and materials to provideyearsofenjoyment, reliabilityandprideofownership.
This product, as with all the Bronze BR range, is hand crafted from top to bottom using traditional woodworking skills for our sumptuous cabinets, married with thestateofthearttechnologyofourrenowned driveunits.
Music is and should be a natural enhancement of life. It stimulates the imagination, changes your mood, helps you relax, and provides endless hours of entertainment.
At Monitor Audio we pride ourselves in attempting to make the listening experienceascloseaspossibletotheoriginal ‘music’ production.
Please read through this manual to familiarize yourself with any safety advice and how best to set up your subwoofer to achieve the very best listening experience.
Please retainthismanualforfuturereference.
© Monitor Audio 200 6 BRW-10 Rev4
2
Safety Instructions
1. Read Instructions
Please read and follow all of the instructions in this manual before enjoying your subwoofer.
2. Keep these instructions
3. Heed all warnings
Any instructions preceded by this warning triangle MUST be followed. Failure to do so may cause personal injury or damage the unit/s.
4. Lifting/Moving
Due to the weight of the BRW-10, care must be taken at all times when handling the product.
5. Power
Unplug this apparatus during lightening storms or when unused for long periods of time.
We would advise it is switched off at the mains power supply. This is a recommended safe practice in order to reduce the risk of electrical fire. Where the Mains Plug is used as adisconnect device, such adisconnect device shall remain readily operable.
6. Power Cord Protection
Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles and the point where it exits from the apparatus.
7. Polarised Plug (Certain countries only)
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit into your outlet. Consult an electrician for replacement of the obsolete outlet.
8. Water & Moisture
Do not use the BRW-10 near water - for example, bathtub, washbowl, kitchen sink, and washing machine, in a wet basement or near a swimming pool. The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus. Please ensure that no liquid is
spilt on the appliance, especially on the rear panel where the power cord enters the amp. To reduce the risk of fire or electric shock. Don’t expose this apparatus to rain or moisture
9. Heat/Humidity
The BRW-10 should not be placed near any heat source such as radiators, open fires, stoves, direct sunlight and any other appliance that produces heat. This product is designed for use within the home environment. Exposure to extreme temperatures & humidity when placed on patios or open conditions could adversely affect the wooden cabinet.
10. Ventilation
The BRW-10 should be situated so that its location or position does not interfere with its own proper ventilation. The ventilation should not be impeded by covering the ventilation openings with items such as newspaper, table cloths, curtains, etc. It
should not be placed in any purpose built location without suitable ventilation being provided.
© Monitor Audio 200 6 BRW-10 Rev4
3
11. Damage requiring Service
Qualified personnel should service the appliance when:
Thepower cord or plug has been damaged.Liquid has been spilt on the rear panel.TheBRW-10 has been dropped or the enclosure damaged.The BRW-10 does not appear to operate normally or exhibits a marked
change in its performance
12. Servicing
The user should not attempt to service the appliance beyond that specified in this manual. Only qualified personnel should carry out all other servicing requirements.
13. Cleaning
Before cleaning it is advisable to disconnect the BRW-10 from the power supply. Avoid touching the BRW-10 drive unit whilst cleaning, as any damage will impair its performance. You will fully appreciate that great care and attention has gone into the materials chosen to produce the Bronze BRW-10. It is our intention that it should provide a lifetime of musical pleasure. A gentle wipe with a dry, clean cloth is all that is required to remove any dust. Treat it as you would a fine piece of furniture because that is how it has been designed.
Re-cycling
Disposal of Waste Electrical and Electronic Equipment (WEEE) by User in Private Households in the EU
This symbol on the productor accessories indicatesthat they must not be disposed of with your house hold waste. Instead it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for recycling WEEE. The separate collectionand recycling of your waste equipmentwill help conservenatural resources and ensure that it is recycled in a manner that protects human healthand the environment.
For more specific information about where you can take your equipment for recycling pleasecontact yourlocal city/council office, your local waste disposal serviceor the outlet whereyou purchasedthe product.
RoHS Declaration of Conformity
Directive 2002/95/EC of the Europe an Parliament and of the Council on the reduction of the use of certain hazardous substances in electrical and electronic equipment, January 2003
Background
The RoHS directive restricts the use of Lead (Pb), Cadmium (Cd), Mercury (Hg), hexavalent Chromium (CrVI), polybrominated biphenyl (PBB) compounds, and polybrominated diphenyl ether (PBDE) compounds in electrical and electronic equipment sold in the EuropeanUnion.
© Monitor Audio 200 6 BRW-10 Rev4
4
Foot Fixing
The BRW-10 comes with rubber feet for fixing to the bottom of the cabinet. Also included are self taping screws to fix them to the bottom of the cabinet. These are very simple to attach, but please ensure care is taken at all times and the correcttools are used.
BEWARE. The screws are very sharp, and could cause injury if care is not taken when handling them
© Monitor Audio 200 6 BRW-10 Rev4
5
1
2
4
6
Amp Panel and Controls
8
10710a
9
3
5
© Monitor Audio 200 6 BRW-10 Rev4
6
1. Stand-by / On Indicator
The LEDindicates whether theunit isin stand-bymode or operational.
2. RCA Line Level Inputs (Left & Right)
This is the only method of signal input connection to the BRW-10. When using a stereo amplifier system, connection can be provided by a pair of high-quality signalcables from thepre-out sectionof an amplifier.Ifa digital A/V processor or A/V receiver/amplifier is to be used, a single cable can be connected from the ‘sub out’ or LFE connection on the amplifier to the RCA input connection on the BRW-10 labelled ‘R’. The RCA input marked ‘L’ in this case will remain unused.
Note: - cable lengths should not exceed 10 metres to avoid interference from other electrical appliances.
3. Volume Control
This control allows the level or volume to be adjusted in order to achieve a balanced overall sound. To use this facility you will need to play a selection of familiar music or film excerpts. Start with the volume at minimum and increase the level controluntil a balancedsound is established. If using an A/V processor or A/V receiver amplifier, the system can adjusted by the test tone function within the set-up features. (Refer to the set up section in the A/V processor or A/V receiver amplifier user guide.) When the BRW-10 is correctly set-up, you shouldnot be able to identifyits locationeasily in theroom.
4. Crossover Frequency Control
The crossover frequency control only operates when the low pass filter switch (refer to section 3.) is in the ‘In’ position.The crossover frequency control is used to set the upper frequency limit (low pass) of the BRW-10. The crossover control should be set in accordance with the size or bass output of the main/satellite speakers. Refer to the chart below as a guide to setting the crossover frequency control to the optimum position. Much will depend on the correct low frequency response of the main speakers and their position in your room. Experimentation isadvisable.
Type of main speaker Crossover control setting
Largefloor-standingspeaker 40-60Hz
Smallfloor-standingspeaker 50-70Hz Largestand-mount/bookshelfspeaker 50-80Hz Smallstand-mount/bookshelf speaker 60-90Hz
Smallsatellite speaker 80-160Hz
5. Phase Control Switch
The Phase Control is used to synchronise any delay between the BRW-10 and main/satellite speakers. When the BRW-10 is in phase with the main/satellite speakers the sound should be full bodied. Sit in a normal listening position whilst adjusting the phase switch. Help from another person may be required in order to do this easily. When set correctly the location of the subwoofer should be almost undetectable. Experimentation is advisable in order to achieve optimum results. However it should be noted that in most cases the phase control switch should be set to 0 degrees, especially when using a digital A/V processoror A/Vreceiver amplifier.
© Monitor Audio 200 6 BRW-10 Rev4
7
6. Power Mode Switch with On-Auto-Off Facility
The Power Mode Switch has three positions: ‘On’–‘Auto’–‘Off’.When the switch is in the ‘Off’ position the subwoofer will not function. In the ‘Auto’ position the subwoofer will automatically switch on when an input signal is received. It will remain on. If no signal is received for around 15-20 minutes, the BRW-10 will then switch into standby mode until a signal is received once more. With the switch in the ‘On’ position, the subwoofer is permanently switched on under all conditions.
7. Warning Information
The followingwarningsymbolsare foundon theamp panel. The meaningsare:
This lightening flash with an arrow head symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the products enclosure that may be of sufficientmagnitudeto constitutea riskof electricshock tothe persons.
Warning: To reduce the risk of electric shock, do not remove cover (or back) no user-serviceable parts inside. Refer servicing to qualifiedservice personnel
This exclamation point within an equilateral triangle is intended to alert the user to presence of important operating maintenance (servicing) instructionsin the literatureaccompanyingthe appliance
8. Mains Power Switch
The Mains Power Switch should be switched to the ‘Off’ position when the BRW­10 will not be used for extendedperiods. The switch mustbe in the ‘On’ position for the sub-wooferto function. WARNING: Due to the mains switch being located on the rear panel, the apparatus must be located in the open area with no obstructions to access the mainsswitch.
9. Mains Voltage Selector
This is factory setto your country’s mains voltagespecification.Do not attempt to adjustthis as this may leadto permanentdamageto theproduct and even the risk of fire.
10. IEC Mains Power Connector/ Fuse Location
The BRW-10 is supplied with a two-pin mains input socket for connection to the mains supply. Use ONLY the appropriate IEC mains lead provided with the product. Also fitted is an external mains fuse. If a fuse blows during operation a spare fuse is provided within the fuse holder for replacement. If you wish to change the fuse, you can do this by removing the IEC mains lead and carefully levering out the original fuse from its holder below the IEC mains input socket (10a). If the fuse blows again it is advisable to seek help from an authorised service agent. DO NOT attempt to re-fit a further fuse as this could result in
serious damage to the amplifier unit.
© Monitor Audio 200 6 BRW-10 Rev4
8
Positioning/Initial Set Up
The BRW-10 should now be sited in the most suitable position, preferably not directly in the corner of a room as this may cause excessive bass boom. Once a desirable position is achieved it is important to check if the cables are long enough to reach comfortably without being under tension. Leave the BRW-10 unplugged until the installation procedure is completed. The optimalcontrol settingswill depend entirelyon your system configuration.For initial trialsset the controlsas follows:
Volumecontrol Shouldbe set tominimum Frequencycontrol Shouldbe set tothe minimumposition(40Hz) Phase control Shouldbe set tozero degrees Powerswitch Shouldbe set to‘Auto’
Input connectionscan be made at thisstage beforethe poweris connectedto theBRW-10. Never connect ordisconnectthe RCA input lead connection with the BRW-10 switched on.
Set Up
Once the input cables are connectedand the controls are set in accordance with the initial set-up procedure above, the BRW-10 can be connected to the mains power supply and switchedon. Do not play any musicat this stage.With thePower ModeSwitch in the ‘Auto’ position,the unitshould remain in standbyuntila signal is received.
Play a variety of music/ film excerpts starting at a very low volume level, increasing to an averagelisteninglevel onceyou aresure everythingis workingcorrectly.Check the back of the BRW-10, the LED indicator should now indicate it is ‘ON’. Please now follow the bulletedinstructionsbelow: -
If using the crossover frequency control please adjust in accordance
with the table on page 7 further fine-tuningmaybe required.
The Phase Control can now be set ref. See page 7 for information on
this function
The volume control can now be set to finish the set-up procedure. It is important to try a variety of music and film excerpts with which you are familiar in order to obtain the optimumoverallsettings.
© Monitor Audio 200 6 BRW-10 Rev4
9
Specification
Lowfrequency limit:- 27Hz Upperfrequency limit:- 40 – 120 Hz Variable Lowpass filteralignment:- 4thorder24db/octave AmplifierOutput:- 150 Watts(R.M.S) Amplifierclassification:- Class- D Digitalamplifier
Drivercompliment:- 1 x 10” MMP®MK2 longthrow driver Dimensions:- Millimetres:- 320 H x 320 W x 340 D
Inches:- 125/8x 125/8x 133/
All dimensionsexcluding grille Weight(unpacked) 12.5 Kg (27.5lbs) InputImpedance: - 20K Ohms Mains inputvoltage:- 115 Vac / 230 Vac Factory Preset.
Do not adjust
8
Finishes:- BlackOak,Cherryand Walnut vinyl’s. All fitted
witha black grille.
© Monitor Audio 200 6 BRW-10 Rev4
10
Guarantee and Service
Valid upon completion of the incorporated warranty card and its return within 30 days of purchase.
This equipment has been fully tested prior to dispatch from the factory. Both the craftsmanship and the performance of this product is guaranteed against manufacturing defects for the period of one year from the date of purchase (see conditions below), provided that the product was supplied by an authorised MonitorAudio retailer under the consumer sale agreement.(The words ‘consumer sale’ shall be construed in accordance with section 15 of the supply of goods act
1973). Monitor Audio accepts no responsibility for defects arising from accident, misuse, abuse, wear and tear, modification or operation outside of that specified within this instruction manual. Neither will responsibilitybe accepted for damage or loss occurring during transit to or from the parties claiming under this guarantee.
This guarantee covers both labour and parts. The liability of Monitor Audio is limited to the cost of repair or replacement of the defective parts (at the discretion of Monitor Audio) and under no circumstances extends to consequentiallosses or damage.
Claims under this Guarantee
The equipment should be returned in its original packaging to the original supplier where possible, or to any other authorised Monitor Audio dealer. If it is not possible to return the equipment by hand, then it should be sent carriage prepaid via a reputable carrier. If the original packing is not available replacement packaging can be purchased from Monitor Audio. If you have any difficulties complying with these requirements please contact us at the following address:
CustomerService Tel: 44 (0) 1268740580 MonitorAudio Ltd. Fax: 44 (0) 1268740589 Unit2, 24 BrookRoad Internet: www.monitoraudio.co.uk Rayleigh Email: info@monitoraudio.co.uk Essex SS67XL England
Thisguaranteedoes not affect thestatutoryrights of the consumer under UK law.
© Monitor Audio 200 6 BRW-10 Rev4
11
EC Declaration of Conformity
EC Declaration of Conformity
product described in this manual
We, Monitor Audio Ltd. Unit 2,24 Brook Road Rayleigh Essex SS6 7XL England
Declare in own responsibility, that the BRW-10 is in compliance with Technical Standards/Council Directives:
(LVD) 73/23/EEC Low Voltage Directive EN60065: 09.93+ A11:09.97 Safety requirements for mains operated electronic and related
apparatus for household and similar use.
(EMC) 89/336/EEC Electro Magnetic Compatibility EN55013: 08.90+A12:08.94+A13:12.96 Limits and methods of measurement of radio disturbance
characteristics of broadcast receivers and associated equipment.
EN55020: 12.94+A11:12.96 Electro magnetic immunity of broadcast receivers and associated
equipment.
06
EN61000-3-2: 04.95+A1:1998+A2:1998 Electro magnetic compatibility (EMC) –Part 3: Limits
Section 2: Limits f or harmonic current emissions(equipment input current up to and including 16 Ampere per phase).
EN6100-3-3: 01.95 Electro magnetic compatibility (EMC) –Part 3: Limits –Section 3 : Limits of
voltage fluctuations and flicker in low-voltage supply s ystems f or equipment with rated current up and including 16 Ampere per phase.
Dean Hartley (Technical Director) 30 May 2006 Monitor Audio Ltd England
12
© Monitor Audio 200 6 BRW-10 Rev4
Data Protection
We at Monitor Audio are committed to respecting the wishes and privacy of our customers. Any information you provide will be held in the strictest confidence and only used within the Monitor Audio organisation for the provision of services suchas warrantyclaimsor spare parts.
We may wish to contact you in the future to ensure you are happy with the productsand standardsof servicewe provide and to keep you up-to-datewith the latestproducts and promotionswehave tooffer.
Shouldyou wish not to be contacted by us eitherby post,e-mail or phone, please tick the box on the warranty card. Alternatively you can request not to be contactedin future by writing to CustomerService, at the address on the previous page.
Owner Information
Product Details
Model BRW-10 ProductSerial No ………………………………….. Amppanel SerialNo …………………………….. DateofPurchase ……………………………………
Dealer Details
DealerName ………………………………………………………………………………………………. Address ……………………………………………………………………………………………………… Town,Post code, Country ……………………………………………………………………………. e-mailaddress ……………………………………………………………………………………………
MonitorAudio reserves theright to alter specificationswithoutnotice.
© Monitor Audio 200 6 BRW-10 Rev4
13
Loading...