Moneual RYDIS MR6550 User Manual
User Manual
Copyright ⓒ 2012 MONEUAL Inc. All rights reserved. The MONEUAL, MONCASO, MiNEW, RYDIS, SONAMU
are trademarks, or registered trademarks of MONEUAL Inc. in the Republic of Korea and/or other countries.
www.moneual.com
Robot cleaner RYDIS MR6550
Robot cleaner RYDIS MR6550
Ver 1.0
RYDIS MR6550
User Manual
4 RYDIS MR6550
User Manual
ENGLISH
Product features
Using the powerful BLDC(suction) motor, the product
maximizes the cleaning capability. The BLDC motor has
the performance of the 20~30% stronger output than that
of DC motor of the same class and also has the lifetime
of approximately 5,000 hours that is 10 times longer than
that of a typical DC motor.
Having a slim design with the height of 82mm, the product can clean the location that a hand cannot reach and
is not easy to clean, such as under the bed, under the
sofa, etc.
As the function that mainly cleans the dark floor space
with no light, Shadow cleaning mode allows the cleaning
of the deep locations under a bed or a sofa that were
impossible to clean with the existing vacuum cleaners.
The product provides the most suitable cleaning function and performance for the cleaning
environment and sage through various cleaning modes.
Automatic
cleaning
Focused
cleaning
Corner
cleaning
Manual
cleaning
Reservation
cleaning
High-performance BLDC motor
82mm slim design
Shadow cleaning mode
Various cleaning modes
82mm
RYDIS MR6550
User Manual
5
ENGLISH
Once being mounted on the left/right of the
body of the cleaner, the twin side brushes
allow the cleaning of the deep locations that
are difficult to clean only with a vacuum suction system
The product uses a environment-friendly battery that
does not contain the harmful heavy metals and acids to
human body and complies with the environment
protection. The lithium iron phosphate battery has the
lifetime of approximately three times longer (1,000 times
of charging/discharging) than that of the existing
lithium-family or nickel-family batteries and provides the
high safety because it is strong against high temperature
and has almost no risk of explosion.
The room indicator allows the user to set various
cleaning zones. It has, not only a virtual wall function
that blocks the cleaner from entering a space, but also
the function to divide the cleaning space into up to three
sections for convenient cleaning.
※ Indicator is included in certain models.
※ Mopping guard and cloth are included in cetain models.
With the mounting/dismounting microfiber dustcloth
mounted, the cleaner can remove even fine dusts
conveniently.
Twin side brushes
Environment-friendly lithium iron phosphate
Room indicator system
Mounting/dismounting microfiber dustcloth cleaning
6 RYDIS MR6550
User Manual
ENGLISH
Table of Contents
Cautions for safety
Product composition
Cautions before using the product
Name of each part of the product
Robot cleaner
Charger
Indicator
Installing the product
Descriptions for remote controller buttons
Basic cleaning (Automatic cleaning)
Using advanced cleaning functions
Focused cleaning
Cleaning corners
Shadow cleaning
Selecting a room for cleaning
Mop cleaning
Cleaning through manual control
Setup of time and reservation
Setting reservation
Using the indicator
Using the product in the room assortment mode
Using through setup of cleaning areas
Managing the product
Language Selection
Cleaning the dust box
Replacing the filter
Cleaning the Sensor
Cleaning wheels
Cleaning the dust inlet
Battery usage and management
Voice announcement list
System check Code List
Checkpoints before request for after-sales service
Product specifications
7
11
12
13
13
14
15
16
19
20
21
21
22
23
24
25
26
27
27
28
28
30
32
32
33
34
35
35
36
38
41
42
44
45
RYDIS MR6550
User Manual
7
ENGLISH
Meanings of caution icons
Before using the product
Refers to important information, definitions, general
knowledge, and references.
If you do not follow the instruction with this warning icon, a
serious injury or property loss may occur.
If you do not follow the instruction with this danger icon, a
serious injury, death, or property loss may occur.
Important
Warning
Danger
Cautions for Safety
The instructions with the following caution marks must be carefully read and followed in
order to use the product properly and to prevent accident or damage which may occur
during the operation of the product.
Remove light clothes or fragile materials from the floor.
It may prevent robot cleaner from moving or cause a trouble.
Remove obstacles on the floor where robot cleaner operates.
The product is unable to travel to areas which are blocked by obstacles of certain height.
Do not install the product in a place exposed to direct sunlight.
Direct sunlight may cause discoloration of the product.
Adapters may cause electric shock or fire due to overheating during charging.
Do not install the charger on an inclined floor, and do not cause impact to the charger.
The charger may become damaged or broken.
Install the charger at the location where robot cleaner can be easily found.
If the site is in a corner or has many obstacles around it, automatic charging may not be possible.
Do not use the product in the room with an unattended child or an elderly person.
A child or an elderly person can become frightened or injured.
Make sure that the charger is always plugged into a power source.
If no power is supplied to the charger, you cannot use the function of robot cleaner charging after
automatically returning to the charger.
8 RYDIS MR6550
User Manual
ENGLISH
In using the product
Do not stand or sit on the product.
Movement of the product may cause an injury or the product can be damaged.
Do not use the product on a narrow and elevated space such as on a desk.
Robot cleaner can fall off and result in a person’s injury or some damage to the product.
Make sure that no liquid enters or falls on the product.
The product may malfunction or can be damaged.
If the product happens to vacuum plastic bags or other such things, they should be immediately
removed.
If the dust intake gets clogged and the product is used for a long time with the internal motor heating,
the product will be damaged.
Do not use the enclosed battery charger for charging of any other product.
The charger or other products can be damaged.
Make sure that clothes, hair, fingers or other body parts are not caught by the wheels.
An injury may occur.
Do not press the bumper of the product severely or give excessive shock.
The bumper sensor can be damaged and then work abnormally.
Do not keep or use the product at too low or too high a temperature.
Do not use the product at a temperature of - 5℃ or lower or 35℃ or higher.
Do not operate robot cleaner with the dust box full.
It can cause reduction in suction power.
Check if the filter is inserted into the dust box.
If the robot gets activated with no filter, it can cause product failure.
Prevent the main brush and the side brush from being clogged with hairs or other foreign
substances.
It can cause noise and reduction in sucking power or damage to the product.
Before using the product, clear away any obstruction from the floor.
Small dish towels, bath towels, pads, telephone lines, power cables, strings or belts can be entangled with the operating wheels or the brushes.
Make sure to remove things that can be easily broken (ceramic wares, glass cups, etc.).
Do not use robot cleaner on the wall or on the mirror or glass floor.
Robot cleaner might not be able to recognize glass or a mirror as an obstacle because it uses an
infra-red light sensor to detect an obstacle.
Avoid using the product in a utility room, in the room with a wet floor, on the stairways, on a
table, on a shelf, in a storage room, in a commercial building and outdoors.
If you have dropped the product or caused an impact to the product, contact the designated
service center immediately.
RYDIS MR6550
User Manual
9
ENGLISH
Electrical cautions
Make sure to use only the specified voltage and current.
Power supplies outside the specification ranges may cause a serious damage to the product.
If Robot cleaner is stored for long time without being used, the body battery can be discharged.
When storing the device for a long period of time, make sure to turn off Power switch on the rear.
Do not use a damaged power cord or plug.
There is chance of shock and/or serious injury.
If the power cord of the charger is damaged, contact the service center immediately.
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or
similarly qualified persons in order to avoid a hazard.
Make sure that the power cord is not pulled or pressed down by doors.
The power cord can be pulled out or damaged.
When connecting / disconnecting the plug into / from the receptacle, make sure to do so by
holding the plug part, rather than pulling on the cord.
Do not touch the power cord with wet hands.
You can get shocked.
If robot cleaner touches water, unplug the power plug and dry it completely before using again.
An electric shock or a fire may occur. If water enters the product, contact the service center.
Use the enclosed charger only.
The product may be damaged due to overvoltage, or a fire or electric shock may occur.
Do not install the charger in a place which is damp or dusty, where water splashes or where
steam is emitted.
The product may malfunction, or a shock or damage of the product may occur.
Do not contact any metal objects such as clip and pin to the charger terminal.
It can cause electric shock and fire.
For indicator power, use rated batteries and adapters.
If not, the product can be damaged set on fire or it may not work.
In case of insufficient indicator battery, replace with a new one.
Without batteries, indicator functions may not work normally.
10 RYDIS MR6550
User Manual
ENGLISH
In product management
Others
Danger
Federal Communications Commission
Use the standard filter only.
No warranty service will apply to any error or failure of the product caused due to a substandard filter.
If cleaning the product, make sure power is off first.
If you happen to care for the product while it is working or the power is still connected, injury is possible.
Clean Main Brush, Side Brush, Dust Bin, Dust Bin Filter, and Dust Suction Inlet periodically.
If the product is used for a long time without cleaning, it can work abnormally and cause product failure.
Do not operate the product in a site with flammable substances.
This includes alcohol, gasoline, distilled water, thinners, ashtrays with flames, candle lights stoves.
Disassembling or repairing the product must be performed by a designated service center or
authorized engineers only.
Tampering with the product can lead to damage or shock.
Do not discard the battery carelessly.
Putting old batteries near fire or direct sunlight for prolonged periods can cause fire and/or explosion.
Discard used-up batteries safely according to local regulations.
Do not place hot or flammable objects such as cigarettes, candles, heaters, matches or gasoline
near product.
The product can become badly damaged or a fire may break out.
Do not use the product near an explosive object or in an explosive place.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
This device complies with part 15 of the FCC Rules,
Operation is subject to the following two Conditions :
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired
operation. for compliance could void the user’s authority to operate the equipment.
RYDIS MR6550
User Manual
11
ENGLISH
Basic Components
Product composition
The appearance and specifications are subject to change without prior notice for better product
functions or performance.
Additional accessories by model number.
◆ Side brush 1SET: MR6500-
****
B/F/G/H/L/M/N/P
◆ 2800mA large battery Pack: MR6500-
****
C/F/I/J/L/M/O/P
◆ Mopping Guard + Cloth: MR6500-
****
D/G/I/K/L/N/O/P
◆ Indicator: MR6500-
****
E/H/J/K/M/N/O/P
Main body Charger Charger sdapter Charger adapter
power cord
Remote control &
Battery(2x AAA)
Indicator
(Not supplied with the product)
Brush User manual Quick
User Guide
Dustcloth guard & 2x Dustcloth
(Not supplied with the product)
Battery(2800mA)2x Side brush
2x Side brush Screwdriver
Additional Components
12 RYDIS MR6550
User Manual
ENGLISH
Cautions before using the product
When opening the package, be careful so that no shock applies to the product and its
components.
See Page 16 for the product installation.
Be sure to check the mounting locations (L/R) for the side brushes before installing them.
See Page 17 for the side brushes installation method.
After removing from the product package, charge manually before operating.
In initial opening, the battery may have become discharged and may not work. For manual charging
method, see page 18.
Clear away all large debris from the floor to be cleaned.
Clear away objects, which might break or fall, from the floor. Carpets with decorative embroidery such as
long tassels, may hinder the product from moving normally. Fold the tassels or clear away the carpets.
If the dust box of the robot cleaner gets filled, and is not emptied, cleaning performance will
deteriorate.
After each cleaning operation, check if the dust box is filled up.
See Page 33 for how to clean the dust box.
Remove foreign substances from the location-detecting sensors and wheels.
They may prevent the robot cleaner from moving or cause errors.
See Page 35 for how to clean the location-detecting sensor and wheels.
Children or the elderly may get frightened by the robot.
To prevent children or the elderly nearby from being taken aback, make sure to explain details of product
to them before operation.
Be careful that the robot cleaner does not fall from high places.
If shoes or something similar are put side by side on the shoe shelf at the entrance of the living room,
the robot might see the shoes as floor, falling from the living room. Do not use the robot cleaner in a
narrow site (e.g. desks, tables, etc.) where the robot cleaner can fall.
The cleaner is not able to cross over a threshold higher than 1cm.
When storing the robot cleaner that is completely charged, leave it docked to the charger or
turn off the power from rear part of the body.
In case of storing the robot cleaner after its charging is completed, leave it docked on the charger
or turn off Power switch located at the bottom of the rear side.
※ The appearance, specifications and other parts of the product are subject to change
without prior notice for product improvement.
01.
02.
03.
04.
05.
06.
07.
08.
09.
10.
11.
RYDIS MR6550
User Manual
13
ENGLISH
Name of each part of the product
Robot cleaner(Top)
Robot cleaner(Rear)
① Obstacle- and signal-detecting sensor
② Bumper
③ Control buttons and operation lamps
④ Dust box cover
① Start/Stop Button
② Mode Setup Button
③ Power On/Off Button
④ Focused Cleaning Indicator
⑤ Battery Lamp
⑥ System Error Lamp
⑦ Charging Mode Indicator
⑧ Room Setup Indicator
⑨ Daily Reservation Indicator
⑩ 1-hour reservation setting indicator
⑪ Automatic Cleaning Mode Indicator
⑫ Suction input turbo indicator
⑬ Shadow Cleaning Mode Indicator
① Dust box
② Air outlet
③ Power switch
④ Signal Receiver
Control buttons and operation lamps
1
3 2
4
5
6
7
8 9
10
12
13
11
14 RYDIS MR6550
User Manual
ENGLISH
Robot cleaner(Bottom)
Indicator(Top)
Indicator(Bottom/Rear)
① Location-detecting sensor
② Wheels
③ Charging terminal
④ Side brush mounting pin
⑤ Dust intake
⑥ Main brush
⑦ Dustcloth guard mounting hole
① Signal transmission sensor
② Mode switch button
③ Distance setup button
④ Indicator number setup button
① Battery cover
② Power button
③ Adaptor jack
7
RYDIS MR6550
User Manual
15
ENGLISH
Charger(Front)
Charger(Rear)
① Operation lamp
② Guide signal transmission sensor
③ Charging terminal
① Adapter jack
② Adapter compartment
③ Sensor Signal Distance Adjustment Switch.
1
2
3
16 RYDIS MR6550
User Manual
ENGLISH
Installing the Product
01. Plug the adapter power cord into the adapter and
connect to power outlet.
02. Connect the charger adapter with the charger.
Once the power is connected, the blue lamp will turn on at the front.
For appropriate charging of the product, the charger adapter should
be connected with the power at all times.
The charger should be placed in a location free of obstruction with at least 1m of space on all sides.
The wall facing the rear of the charger should not be made of glass or glossy materials.
Insert the adapter into the compartment of the charger, properly.
If the charger is installed in a site under direct sunlight, automatic charging may not occur or the product can become
discolored.
03. Arrange the position of the charger.
Considering location of the charger and size of the house, set the Sensor Signal Distance
Adjustment switch as 5m to 8m to adjust the signal detecting distance of the robot cleaner.
If the robot cleaner fails to return to the charger, switch the distance setup located on the rear part
of the main body.
◆ If the charger is installed in a narrow space, select 5M. If installed in a large space, select 8M.
◆ If the charger is installed in a narrow space and 8M is selected, automatic charging may not work
properly.
◆ Do not place the indicator on the charger. Signal inference may occur to disrupt automatic charging.
1m
1m
1m
Loading...