Monarch 6150-020 User manual

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Find Quality Products Online at: [e-mail]

TABLE OF CONTENTS

TABLE OF CONTENTS

INTRODUCTION ...................................................................1

COMPONENT SPECIFICATIONS ........................................1

SPSR-IM Interface Module ............................................1

www.GlobalTestSupply.com

ROS-P Remote Optical Sensor.......................................3

FUNCTIONS AND OPERATION ...........................................4

SPSR Interface Module ..................................................4

Connections ..............................................................4

Controls ....................................................................4

LED Indication ..........................................................5

Recharging the Batteries ..........................................5

SPSR-115/230 Series - SPSR-IM with ROS-P ..............6

ROS-P ......................................................................6

Operating the SPSR as a triggering source .............6

BATTERY DISPOSAL ...........................................................7

SENSORS / OPTIONS AND ACCESSORIES ......................8

Find Quality Products Online at: [e-mail]

INTRODUCTION

The SPSR-IM Self Powered Sensor Interface Module is a self-contained,
rechargeable battery powered device for developing a TTL compatible one
pulse per revolution output for triggering external equipment such as vibration
analyzers, spectrum analyzers, stroboscopes, data acquisition equipment,
tachometers, balancers, waveform analyzers and magnetic tape recorders.

The S P S R - 115/230 i s

www.GlobalTestSupply.com

comprised of the SPSR-IM
Interface Module, which

provides power to a sensor
and couples the sensor to
a BNC outp ut; an input
sensor with a visible red
LED light source (ROS-P);

(SPSR-IM, ROS-P and Universal Recharger)

SPSR-115/230

and a battery recharger.

Optional sensors such as an optical
laser sensor (ROLS-P-not shown),
in f rare d sen sor (IRS- P ), or an
amplified magnetic s ensor ( MT-

190P) may also be combined with the
SPSR-IM Interface Module when

IRS-P

Infrared Sensor

Magnetic Trigger Sensor

appropriate. (See separate instructions for these confi gurations.)

MT-190P

COMPONENT SPECIFICATIONS

SPSR-IM Interface Module

Internal Batteries: Nickel Metal Hydride (NiMH) Battery Pack, 4.8 Vdc
Operating Interval: >40 hours typical with ROS-P (~40mA load)
Charge Time: up to 4 hours

1

Find Quality Products Online at: [e-mail]

Output: TTL compatible pulse, INVERTED or NON-INVERTED – switch

selectable. With an ROS (negative pulse) input, the output will be
a positive pulse when set to inverted or negative pulse when set to
non-inverted. Optionally, the output can be open collector (external
pull up is required).

Bandwidth: 0 to 100 kHz
Battery Current Draw: 12mA with 10 kΩ load (operational)
9V Input Current Draw: 14mA with 10 kΩ load (operational)

www.GlobalTestSupply.com

Power Supply: PSC-2U (operational/charge):
Conforms to UL STD 60950-1
Certifi ed to CSA STD C22.2 No. 60950-1-03
OR 9Vdc to 15Vdc with CA-DCSPSR Cable

LED Indicator: Status indication, see LED Indication section
Output Connector: BNC Connector (female)
Operating Temp: 32° F to 122° F [0° C to 50° C]
Weight: 8.3 oz. [235 grams]
Dimensions: 5.0” x 2.5” x 1” [127 mm x 64 mm x 25 mm]

Remote
Sensor
Input Jack

Recharger
Jack

SPSR-IM Dimensions

2

M16 x 1.5

Green
On Target LED

0.62” [15.9mm] 2.90” [74.0mm]

Find Quality Products Online at: [e-mail]

ROS-P Remote Optical Sensor

Operating Envelope: Up to 3 feet [0.9 m] and 45° from refl ective target
Speed Range: 1 to 250,000 RPM
Illumination Source: Visible red LED, 5 Vdc @ 30 mA
Operating Temp: 14° F to 158° F [-10° C to 70° C]
Output Signal: 5 to 0 Vdc TTL compatible pulse
On-Target Indicator: Green LED on end cap
Material: 303 Stainless steel

www.GlobalTestSupply.com

Lens: Acrylic plastic
Cable Length: 8 feet [2.5 m] Standard
Dimensions: Threaded Tube - 2.90” L x 0.625 “ diameter [M16

x 1.5 x 74 mm] supplied with two M16 jam nuts
and mounting bracket

ROS-P and mounting bracket Dimensions

3

Find Quality Products Online at: [e-mail]

FUNCTIONS AND OPERATION

SPSR Interface Module

The SPSR Interface Module (SPSR-IM) provides power to the input
sensor, receives and optionally inverts the return pulse signal, and provides
a switch selectable positive going 0 to 5 Vdc or negative going 5 to 0 Vdc
pulse train trigger output on a BNC connector. Connections and operation
are common to all SPSR models. Fully charged internal NiMH batteries will

www.GlobalTestSupply.com

typically provide greater than 40 hours of continuous operation. In addition,
the SPSR system can be operated continuously on external power by use of
the recharger/power supply or cable provided.

Connections

Connect the input sensor via the 1/8” [3.5 mm] phone plug to the mating
connector on the SPSR-IM. This sensor may remain connected even
when recharging the internal batteries of the SPSR-IM.

Connect the output signal cable to the BNC connector on the opposite
end of the SPSR-IM and to the external equipment to be triggered.

If operating from the recharger/power supply, connect the recharger
to the connector marked “External DC” on the SPSR-IM and connect
the wall unit to the appropriate power source. When using the CA-
DCSPSR cable, connect the cable to the connector marked “External
DC” on the SPSR-IM and connect the cigarette lighter connector to
the appropriate power source.

Controls

The “Power” switch on the SPSR-IM controls both the operation and the
charging of the system. The unit will only charge from external power
in the power OFF position. In the power ON position, the unit will

4

Find Quality Products Online at: [e-mail]

operate directly from external power any time that it is being supplied.
Otherwise, it functions on internal battery power.

The “Output Selection” switch determines the polarity of the leading
edge of the TTL compatible output signal. In the NON-INVERTING
position, the output signal on the BNC connector will be a negative going
5 to 0 Vdc pulse derived directly from the conditioned sensor output.
When the INVERTING position is switch selected, the BNC output
signal will be a positive going 0 to 5 Vdc, TTL compatible.

www.GlobalTestSupply.com

LED Indication

Unit operational = solid green
Unit charging = blinking red
Charging done = solid red
NOTE: Short red blinks followed by long blink = Charge error,

contact factory

Recharging the Batteries

To recharge the SPSR-IM Interface Module batteries:

1. Connect the recharger/power supply or external power cable
to the “External DC” input connector.

2. Connect the recharger/power supply into a working ac outlet,
or the external power cable to a regulated power source of 5 to
12 Vdc.

3. Be sure the “Power” switch is in the OFF (CHARGE) position.
The red “CHARGE” LED will indicate that the batteries are
being charged. Allow up to 4 hours to fully charge.

5

Find Quality Products Online at: [e-mail]

SPSR-115/230 Series - SPSR-IM with ROS-P

The SPSR-115/230 consists of the SPSR-IM Interface Module described
above, an ROS-P Remote Optical Sensor with eight foot cable and mounting
bracket, and a PSC-2U (115/230 Vac) external power connection. One foot
of T-5 Refl ective Tape is also supplied.

ROS-P

www.GlobalTestSupply.com

When connected to the SPSR-IM as described above, the ROS-P
illuminates the target with a visible red light from a high intensity LED
and detects the refl ected pulses from the rotating refl ective tape target

with an internal photo-detector. The ROS-P Remote Optical Sensor is
capable of detecting a refl ected pulse from T-5 Refl ective Tape targets
at distances of up to 3 feet and angles up to 45 degrees from the target.
The sensor is supplied with a set of two M16 jam nuts and a 90° angle
slotted aluminum mounting bracket.

For most applications, a 1/2” square piece of T-5 Refl ective Tape should
be applied to a clean area on the rotating object. The sensor should be
mounted and optically aligned to illuminate the refl ective target once per
revolution. It is recommended that the optical sensor be placed at a

slight angle (approximately 10-15 degrees) from perpendicular, so
that the sensor will detect only the refl ected pulses from the target.

The sensor should be at least 2 inches and no more than 3 feet from the
target. The green LED On-Target Indicator on the ROS-P will blink at
the input frequency or be continuously illuminated when properly aimed.

Operating the SPSR as a triggering source

Once the ROS-P input sensor is properly mounted and aligned, further
connections and operation should proceed in accordance with the
functions and descriptions under the SPSR Interface Module sections
entitled ‘Connections’ and ‘Controls’.

6

Find Quality Products Online at: [e-mail]

www.GlobalTestSupply.com

Find Quality Products Online at: [e-mail]

SENSORS / OPTIONS AND ACCESSORIES

ROS-P Remote Optical Sensor with 8 foot [2.5 m] cable and mounting

bracket

ROS-P-25 Remote Optical Sensor with 25 foot [7.6 m] cable and

mounting bracket

www.GlobalTestSupply.com

ROLS-P Remote Optical Laser Sensor with 8 foot [2.5 m] cable and

mounting bracket

IRS-P Infrared Sensor with 8 foot [2.5 m] cable for use without

refl ective target at 0.5 inch [12.7 mm] gap (5 to 500,000 RPM)

MT-190P Magnetic Trigger Sensor/Amplifi er with 8 foot [2.5 m] cable

- 0.250” [6.4 mm] operating gap from target, 2” (L) x 5/8”
[50.8 x 15.9 mm]

EC-25P 25 foot [7.6 m] Extension Cable for remote sensors with male

1/8” [3.5 mm] phone plug to female 1/8” [3.5 mm] connector

T-5 Refl ective Tape, 5 foot [1.5 m] roll, ½ inch [13 mm] wide

T-5WP Waterproof Refl ective Tape (honeycomb pattern), 5 foot [1.5

m] roll, 1 inch [25 mm] wide

BP-R Replacement NiMH Battery Pack (for SPSR-IM ONLY)

PSC-2U Universal Recharger with plugs, 115/230 Vac - 50/60 Hz

CA-DCSPSR 6 foot [1.8 m] DC Adapter Cable assembly with cigarette

lighter plug to operate and charge SPSR-IM from 12 Vdc

8