Page 1
TVCCD-370/WS
Thank you for purchasing our products. Please read the manual carefully
before operating.
Warning
* In order to prevent damage caused by fire or electric shock, please do not
put cameras exposed in the moist environment or rainwater.
* Please make sure the adapter is consistent with product specifications,
otherwise it might cause fire, electric shock or damage.
* Pay attention to polarity of the adapter, it might cause some accidents like
fires.
* Please don’t connect multiple cameras with the same adapter at the same
time; overloading of adapter capacity may cause fires.
* Power supply must be firmly fixed so as not to loose to cause fires.
* If the device gets abnormal smell or smoke”, please stop it immediately
and contact with our customer service center.
* If the camera doesn’t work as usual, please do not dismantle it by yours
e
Please contact our local distributor or our maintenance office authorized
b
our company, otherwise we won’t promise warranty.
* Please do not splash water on the product components when cleaning.
Technical Specifications
Item Number: .......................... TVCCD-370/WS
Signal System: ...................... PAL
Sensor CCD: ......................... 1/3" SONY Super HAD II CCD
Horizontal resolution: .............. 700 TV lines
Lens: ....................................... 2.8-12mm
Minimum Illumination: ............. 0 LUX (IR ON)
S/N Ratio: ................................ > 48 dB
Water-resistant: ....................... IP66
Distance: ................................. 15 m
LED: ........................................ 21PCS
Video output: ........................... 1Vpp 75 . Y/C Separated
Connector video: ..................... BNC
Operation temperature: ........... -20°C to +50°C
Power supply: ......................... 12VDC (+/-10%)
Installation
1. Connect the terminating wire of the cable directly to the DC power sourc
e
2. Connect the BNC end of the Camera Cable to an extension cable,
directly to a DVR / Observation System or to a TV/Monitor.
3. Fix up the pedestal on the ceiling, fix up the screw of pedestal.
4. Aim at the scope what you want to watch and then fix up the screw
horizontal angle.
5. Choose a good angle to the aim thing first and then fix up the screw
declining angle.
Page 2
Troubleshooting
1.No picture or unstable
Check the connection of video line or power line
2.The image is so blurred
1)Checking is there something dirt on the lens, then use customized lens
paper or cotton buds with alcohol drenched to clean.
2)Check the focus length and OSD settings
3. The image is so dim
Adjust the CNT of monitor and iris
4. No motion detection frame and privacy shaded frame
Check the option is ON or OFF. Or check the menu parameters
5. Screen color cast in the special environment
Adjust WEB mode or direction
6. The screen glittering
The camera might face to the sun, TV set or computer.
7. Functions are disorder and could not adjust
Restore default settings
8. The camera works abnormal; the surface over-heat; has peculiar smell,
smoke etc.
Please cut off the power supply immediately. Secondly, check the
connection of power supply. Then send the camera to professionals for
maintenance
Accessory List
OSD MENUAL(V1.0)
Warning Please read this manual carefully before installation and use!
OSD CONTROL BY FIVE SWITCH OSD CONTROL BY O
N
SWITCH
SETpush [ SET ] into Main Memu
UP/DOWN[ UP ] or [ DOWN ] for move up and down.
LEFT/RIGHT[ LEFT ] or [ RIGHT ] for modifying the menu parameters.
1.Press Set key to show the OSD Main Menu,
2.Select different memu content by UP and DOWN button
3.Through the left (LEFT) or right (RIGHT) button to change the selection
different modes.
4.Chose EXIT and press SET key to end the setting.
1. LENS
Manual: Please choose‘manual’when use
manual iris lens for the camera
Auto: Please choose‘Auto’when use manual
iris lens for the camera
No. Name Quantity Rem
a
1
CCTV Camera 1
2 User Manual 1
3 Screws 1
Page 3
2. SHUTTER/AGC
AUTO: Auto control of the shutter is enabled.
The shutter speed is controlled automatically
according to the brightness of the scene.
MANUAL: The shutter speed can be controlled manually
3. WHITE BAL(white balance)
ATW: The camera can adjust the white balance au
tomatically according to the color temperature range.
Single press: use for the fixed environment
Page 4
User 1:User can adjust white balance as he need.
User 2: User can adjust white balance as he need
Color rolling suppression: Restrain color rolling
when the frequency of the camera and the testing
temperature are not the same.
Manual: This mode is used for advanced settings,
User can adjust white balance manually from 015
to 056.
4. BACKLIGHT COMPENSATION
Backlight Compensation: when there is strong
back lighting at the back of the monitored object,
you can use this function to get clear images both
for the object and the background
Strong light BLC: by processing light signal or
exposure compensation to achieve backlight
compensation and brightness compensation
OFF: close ‘BLC’ function
Page 5
5. PICT ADJUST
Mirror: This function is used to achieve picture
horizontal reverse.
Brightness: It can adjust the brightness of the
picture (0-255)
Sharpness: It can adjust the Sharpness of the
picture (0-255)
HUE: It can adjust the HUE of the picture (0-255)
Gain: It can adjust the gain of the picture (0-255)
6. ATR
ON: bright/dark compensate open
Sharpness OFF:ATR CLOSE
Page 6
7. MOTION DET
ON: MOTION DET open, one checking area
OFF: MOTION DET close
8. NEXT: NEXT PAGE
9. EXIT: EXIT MENU
10. SAVE ALL
Page 7
11, Privacy Zone
On: turn on the function, it contains 4 privacy
zones.
Off: turn off the function.
11. Day/ Night Mode
Auto: Select this, the camera will show color
image in high lux and will auto change
intoblack/white image in low lux.
Color: select this menu to show color image.
Black/White select this menu to show black/white
image.
Page 8
12. Noise reducing
NR model: choose NR mode.
Y Level: brightness signal
C Level: color signal Return
14.Camera ID
On: turn on the camera ID function
OFF: turn off the function.
Page 9
15.Synchronous Mode: Int Sync
16.LANGUAGE: Including Chinese, English,
Japanese, Germany, French, Russian,
ortuguese, Spanish
Page 10
17.CAMERA RESET: Menu restore to
factory default.
18.BACK: Previous
19.EXIT: Exit Menu.
Page 11
20.SAVE ALL: Save
MONACOR INTERNATIONAL GmbH & Co. KG • Zum Falsch 36 • 28307 Bremen • Germany
Copyright © by MONACOR INTERNATIONAL. All rights reserved.
Loading...