Monacor CS-200CCD, CS-200CCDC Instruction Manual
1
Instruction Manual
CS-200CCDC
Conference Image Processor
For CS-200 Series
2
Contents ........................................................................................................................................................ 2
Overview ....................................................................................................................................................... 3
System Features ............................................................................................................................................. 3
Safety Instructions ......................................................................................................................................... 4
Operation and Features .................................................................................................................................. 5
Front Panel Description ................................................................................................................................. 5
Rear Panel Description .................................................................................................................................. 6
Turn On ......................................................................................................................................................... 7
LCD Instructions ........................................................................................................................................... 8
System Operations & Settings ........................................................................................................................ 9
Mic Positioning ............................................................................................................................................. 9
Set Preset .................................................................................................................................................... 10
Go Preset ..................................................................................................................................................... 11
Protocol Setting ........................................................................................................................................... 12
Video Jump Mode ....................................................................................................................................... 13
Gain Setting ................................................................................................................................................ 14
Reset Settings .............................................................................................................................................. 15
Data Transfer through USB Port .................................................................................................................. 16
Connection .................................................................................................................................................. 17
Contents
3
1. The apparatus is equipped with a graphic LCD screen and 8 control buttons: up, down, left, right,
enter, return, zoom in& zoom out. You can operate the system on it without connecting keyboard.
2. RS485 and RS232 input connectors: comply with CS-200 series (RS232 or RS-485 video camera
signal output, and CS-200 (2400 baud rate).
3. RS485 and RS232output connectors: comply with multi-brand cameras.
4. USB connector data transfer and graphical control software.
5. There are 4 in and 6 out ports for images, in which the two (main-out) can be set for overcome and
individual display; the rest four correspondingly shows input1-> output1.
6. Each video input provides 4 sets of brightness GAIN value individual adjustment.
7. One microphone and camera preset point contrastive table, CS-200CCDC supports up to 1009
microphones and four cameras.
8. Built-in simplified keyboard to control camera directions.
9. Camera preset point storage: 128 points for each camera, 4 cameras at most.
10. A 4-bit DIP switch settings (Reserved).
Overview
System Features
4
Safety Instructions
1. Please read and observe these instructions before installing and using the apparatus.
2. Use only accessories specified by the manufacturer. The manufacturer is not liable for damage
caused by the use of non-specified accessories.
3. Install the apparatus and its accessories carefully. Strike and fierce shaking may damage the
apparatus.
4. Make sure the power cord is fixed properly.
5. Do not overload wall outlets and extension cords as this can result in a risk of fire or short circuit.
6. To reduce the risk of damage from lightning strikes, it is important that all electric cables should
be bonded to the same grounding point.
7. Do not block any ventilation openings to prevent overheating and malfunction.
8. Do not expose the apparatus to rain or moisture.
Humidity may lead inside components to damage. Appropriate shelter is necessary when placing
it outside (Best working environment: Temperature 0°C ~ 40°C <32°F ~ 104°F>, humidity below
90%).
9. Please do not switch on and off the apparatus rapidly.
Rapid switch on and off the apparatus should be avoided all the time to prevent inside sensitive
electronic circuits from being damaged by surges.
10. Do not clean the apparatus and its accessories with chemical solvents. Use only a clean,
dry/dampish cloth.
11. Refer to maintenance technician when the apparatus has been damaged in any way, such as:
A• power-supply cord or plug is damaged
B• liquid has been spilled in
C• has been exposed to rain or moisture
D• has been dropped
E• objects have fallen into the apparatus
F• does not operate normally
12. Note: When the printed circuit board is going through electric static treatment, correct ESD
safety precaution and grounding should be assured.
13. Note: Before connecting the apparatus to main AC, please select the supply voltage in
accordance with the wall voltage in your country to prevent damage. Refer to Installation and
Setting (Page 8) for selecting.
14. Warning: Do not disassemble or remodel the product, as these actions may lead to electrical
shock or damage. The guarantee on the product will become null if the product is ever
disassembled.
5
Front Panel Description
○,
1
Power indicator
○,
2
24×2 bits LCD screen; shows current settings configuration
○,
3
Camera zoom out and speed adjustment
○,
4
Left, for camera direction and menu selection
○,
5
Down, for camera direction and menu selection
○,
6
Right, for camera direction and menu selection
○,
7
Enter, to save settings
○,
8
Camera zoom in and speed adjustment
○,
9
Up, for camera direction and menu selection
○,
10
Return, to cancel settings and go back to top menu
Operation and Features
6
Rear Panel Description
○,1 Power switch
○,2 DC power input: in+ out-, DC 15V~20V (MAX)
○,3 USB 2.0: USB port for PC connection
○,4 Video output 1, for input 1 image
○,5 Video output 2, for input 2 image
○,6 Video output 3, for input 3 image
○,7 Video output 4, for input 4 image
○,8 Output Main 2
Video matrix output 2, output selectable; in override mode, operating camera or adjusting GAIN
will automatically switch to the image.
○,9 RS485 Receiver
For BXB FCS conference main controller speed dome camera control terminal
○,10 RS232 Receiver:
For BXB FCS/ EDC conference main controller RS232 control terminal (jumper is essential)
2nd foot: Received Data (Rx) / 3rd foot: Transmitted Data (Tx) / 5th foot: Signal Ground(G)
○,11 RS485Transmitter: for camera control
○,12 RS232Transmitter: for camera control, RS-422 switchable with interface converter
2nd foot: Transmitted Data (Tx) / 3rd foot: Received Data (Rx) / 5th foot: Signal Ground(G)
○,13 ID: reserved 4 PIN DIP switch
○,14 Video output 1
○,15 Video output 2
○,16 Video output 3
○,17 Video output 4
○,18 Output Main1：
¡õ
7
Video matrix output 1, output selectable; in override mode, operating camera or adjusting GAIN
will automatically switch to the image.
Turn On
After confirming all the wiring is done, switch on the main controller and the LCD will display following
information
B X B S D C S y s t e m V e r 1 . x
Later, the system will start auto-scanning to see if it operate normally
M e m o r y C h e c k . . . . . O K
Or not
M e m o r y C h e c k . . . . . E R R
After scanning completes, LCD will display following information (default page)
1 . M i c P o s i t i o n i n g
2 . S e t P r e s e t
Loading...