Page 1
MOMAN
H2
Headset Helmet Intercom
2-Rider Kit
User Manual
Thank you for choosing MOMAN product. Please read this manual carefully
before use and follow all instructions mentioned herein.
Caring For Your MOMAN Product
Please keep the product in a dry, clean, dust-free environment.
Keep corrosive chemicals, liquids and heat source away from the product to
prevent mechanics damage.
Use only a soft and dry cloth for cleaning the product.
Malfunction may be caused by dropping, impact of external force.
Do not attempt to disassemble the product. Doing so voids warranty.
Please have the product checked or repaired by authorized technicians if any
malfunctions happened.
Failure to follow all the instructions may result in mechanics damage.
Warranty does not apply to human errors.
Package List
Intercom x2
Hook and Loop
Fasteners x2
USB Cable x2 Headphone Velcro x8
Velcro Clip x2
1 Pair of Speakers with
Microphone x2
Screw Driver x2
Back Clip x2
MOMAN
Manual x1
Product Introduction
① On/Off Key
② Indicator Light
③ Function Key
④ Charging Interface
⑤ Knob
⑥ Headset Interface
⑦ Buckle Flap
⑧ Speaker
⑨ Headset Plug
Operation
1. Power On/Off
ON:
Press the On/Off Key for 2 seconds. When you
hear voice prompt, the blue indicator flashes twice.
The system enters the standby mode.
OFF:
Press the On/Off Key for 2 seconds. When you
hear voice prompt, the red indicator flashes twice.
⑩ Butterfly
sticker
⑪ Microphone
2. Pairing & Disconnection 3. Phone Control
2.1 with Two Intercoms
Pairing:
(1)Power on two intercoms and the blue indicators flash twice. The red and
blue indicators flash alternatively, which means two intercoms wait to be
Bluetooth paired.
(2)Then, press the On/Off Key of any one of them while the blue indicator
flashes quickly with voice prompting “Intercom Search”; the red and blue
indicator of the other keeps flashing alternatively. After few minutes, they are
paired automatically with blue indicator flashing slowly.
Disconnect:
Press the Function Key for 2 seconds to disconnect the intercoms. Press it
again to reconnect.
※ The distance between intercom and mobile phone should be within 1 meter.
※ When two intercoms are paired successfully, there is no need to pair them
repeatedly. Under standby mode, they will be paired automatically after a few
seconds.
※ The automatic connection function is available within five minutes after
disconnection. If the connection fails again, you can manually press the
Function Key once for searching and matching.
2.2 with Mobile Phone
(1) After power on, the blue indicator flashes twice. The red and blue indicator
flashes alternatively, which means the intercom waits to be Bluetooth paired.
(2) Turn on the Bluetooth function of the mobile phone, search and select
“MOMAN H2” to connect and pair. The voice will prompt “Bluetooth
connected”.
※ The distance between intercom and mobile phone should be within 1 meter.
※ If the intercom has pairing record with the mobile phone, they will be
connected after power on, provided that the Bluetooth is turned on.
Answer the call:
Automatic answer:
is no operation after 8 seconds, it will answer the call
automatically.
Reject the call:
seconds until you hear the “beep” sound.
End the call:
Redial:
4. Music
(1) Under Bluetooth connection mode, press the
Function Key to play/pause music.
Next Music:
(2)
Previous Music:
(3)
5. Volume Adjustment
Decrease:
(1)
counterclockwise.
Increase:
(2)
※ There is voice alarm for two high or two low volume.
6. FM Radio
Turn on:
(1)
Key twice to switch to the FM radio.
Select Channels:
(2)
release to adjust and select channels. Continuously
rotate the Knob to select different channels. Rotate
the Knob continuously to enter volume adjustment.
Turn off:
(3)
press the Function Key
press and hole the Function Key for 3
press the Function Key.
In standby mode, press the On/Off Key twice to dial the last call number.
turn the Knob counterclockwise.
continuously turn the Knob
continuously turn the Knob clockwise.
under standby mode, press the Function
press the Function Key twice to get back
When the phone calls and there
turn the Knob clockwise.
quickly rotate the Knob and
to the previous mode.
※ If the signal is weak indoor, you could try to turn on the FM radio near
window or in the open area.
※ When FM radio is turned on and there is a phone calling, the machine will
cut off FM radio automatically and connect to the mobile phone. It gets back to
the FM radio when the call ends.
7. Multi-Mode Switch
7.1 Between Intercom and Music/FM Radio:
(1)In intercom mode, press the Function Key for 2 seconds and you hear “beep”,
indicating the intercom mode exits, and enter the switch between Music/FM
radio;
Turn on/off FM Radio:
(2)
Turn on/off Music:
Back to Intercom:
7.2 Between Intercom and Mobile Phone:
(1) If the machine is connected with mobile phone, the intercom will disconnect
when there is call. When the call ends, it will get back to the intercom mode,
which takes 5 seconds.
7.3 Function Priority
Level 1:
Mobile Phone
Level 2:
Intercom
Level 3:
Music/FM Radio
Press the Function Key twice;
short press the Function Key;
long press the Function Key.
8. Language
When it is on, press On/Off Key and rotate the Knob to
change the language of voice prompt.
Page 2
Installation Installation
1. Method 1: Install with Back Clip
① Use the screwdriver to loosen the screws of the back clip so that it can open
to a proper extent.
② Open the helmet liner, insert the clip into the right position on the left side of
the helmet and tighten the screw.
③ Slide the intercom into the back clip slot to make sure it locks firmly.
④ Open the helmet liner (ear position), clean the EPS surface of the helmet,
and stick a piece of horn Velcro on the left and right sides of the helmet.
⑤ Stick the speaker on the fixed Velcro surface and the speaker with short line
should be installed close to the machine. Fix the microphone and arrange the
helmet lining and cable.
⑥ Insert the headset into the jack of the intercom and tie up the headset cable.
Method 2: Install with Velcro Clip 2. How to Remove the Intercom from Helmet
Separate the hook and loop fasteners. First stick the hook onto the Velcro
clip; choose the right installation position on the helmet and stick the loop to
the position. Install the intercom onto the Velcro clip.
The installation of speakers can refer to the description above.
First unplug the headset, then press the xed buckle in the middle of the
back clip with one nger (push towards the side of the helmet), so that
the back clip hook is detached from the intercom, and push the intercom
upwards to let it slide out of the back clip smoothly to complete the
disassembly.
3. How to Fix the Headset Plug (If necessary)
Unscrew the screws on the back of intercom with
screwdriver, open the buckle ap, plug in the headset
plug and tighten the screws. If you need to plug
out the headset, please open the buckle ap by
unscrewing the screws.
1. Before using the Bluetooth intercom, please use the attached charging
cable to charge the intercom. The small type-C interface on the charging
line is connected to the USB charging interface of the Bluetooth intercom,
and the large USB connector on the charging cable is connected to the
following charging interface for power supply:
A. USB interface of computer;
B. A mobile power supply with DC 5V output;
C. A USB power adapter with DC 5V output.
2. When charging, the red LED is always on, and when fully charged, the red
light goes out slowly. It takes up to 2.5 hours to fully charge the unit.
Specications
Transmission Range
Connection Distance with Mobile
Bluetooth Version
Bluetooth Protocol
Charging Port
Standby Time
Working Time
Battery
Charging Time
Charging Voltage
Speaker Diameter
Frequency Range
Temperature Range
up to 800m
20m
5.0
A2DP, AVRCP
Type-C
300H
20H
900mA
2H
5V
40mm
2.4GHz
-20~50
℃
Notes
1. If you do not use intercom for up to one month or more, please charge
the intercom once every two months in order to protect the lithium battery;
2. The storage temperature of this product is -20 ℃ to 50 ℃ , and do not
store in the environment with too high or low temperature, otherwise, the
service life of the product will be aected;
3. Do not expose this product to re to avoid explosion;
4. Only two screws on the back of intercom can be opened. Do not open
other screws to the intercom to avoid short circuit of main board or battery
damage.
Moman (UK) Limited
Unit 25 Basepoint Business Centre, Aviation Park, West Christchurch, United
Kingdom BH23 6NX
www.momanx.com
@MomanGlobal
https://moman.co/youtube
Loading...