Molpir ANT1500 Installation Manual

~ 1 ~

NM_ANT1500_001_01082016_EN

4

Installation and user manual

ANT1500

~ 2 ~

CONTENTS

1. ANT SR 1500 for receiving satellite TV in mobile applications ….3

1.1. Safety instruction for mounting and usage………………………………………..4

1.2. Compatibility of Set Top Box (STB)………………………………………………….…4

1.3. Signal Reception…………………………………………………………………………….…...5

1.4. System description………………………………………………………………………….…..5

1.5. Power requirements…………………………………………………………………………..…6

1.6. Antenna Components………………………………………………………………………..…6

1.6.1. Exterior antenna unit – ODU……………………………………………..………..…9

1.6.2. Interior antenna unit – IDU………………………………..…….……………….…10

1.6.3. ANT1500 - DP package contents………………………………….……………. 10

1.6.4. ANT1500 – SP package contents………………………………….…….……...11

1.7. Unpacking, Inspection and installation planning………………….……..……11

1.8. ANT1500- main parametres………………………………………………….………..…12

1.9. Dimensions…………………………………………………………………………….……….….12

2. Installing the antenna………………………………………………………………………….12

2.1. Tools required…………………………………………………………………………..…..13

2.2. Installation of Roof rack on Vehicle Roof………………………………………13

2.3. Selecting the Location on the Rooftop…….……………….………………....14

2.4. Assembly order of Antenna´s Bracket………………………………………..14

2.5. Installation of Antenna on Bracket…………………………………………….….21

2.5.1. Antenna Bracket………………………………………………….………………..21

2.5.2. Antenna Installation Kit- package content………….…………..…..22

2.5.2.1. Package AKT1000000 for ANT1500 – SP ……….………………...22

2.5.2.2. Package AKT1000000 for ANT1500 – DP…………….…………….22

2.5.2.3. Antenna Installation Kit AKT0000048 …………………………….. 23

2.5.2.4. Optional equipment for Antenna……………………….………….……24

2.6. Antenna Installation on Brackets………………………………….…………..…24

2.7. Installation on a Double Decker Bus…………………………….………….….26

2.8. Installation of IDU and DVB-S / DVB-S2 receiver………….………….27

2.9. Components connecting…………………………………………………………..….28

2.9.1. Sample of connecting ANT1500 - DP (Dual Pol)………………………...28

2.9.2. Sample of connecting ANT1500 – SP (Single pol) …………………..…31

2.10. Output configuration – polarization and Ku band……………………....31

2.10.1. Output signal ANT1500 – SP…………………………………………..…31

2.10.2. Output signal ANT1500 – DP……………………………………….……32

2.11. Power source of system ……………………………………………..…..32

2.12. Antenna´s cable routing………………………………………………..…34

3. IDU Configuration and Set up of Antenna´s Parameters…….…………34

3.1 Configuration of IDU unit………………………………………………..……………..34

3.2.1. Configuring the ANT1500 with the IDU Web interface……………...35

3.2.1.1. Antenna error status…………………………………………………..…….47

3.2.2. Configuring the ANT1500 with IDU display…………………………..……48

4. Troubleshooting…………………………………………………………………………………54

5. Acronyms and Abbreviations…………………………………………….……………….55

~ 3 ~

1. ANT1500 for receiving satellite TV in vehicles in motion

Safety

This antenna is one-way receive only and does not emit radiation.

Warnings

DO NOT INSTALL AN ACTIVE MONITOR IN RANGE OF THE VEHICLE’S DRIVER TO

AVOID DISTRACTION WHILE IN MOTION.

This product is designed for entertainment of the passengers in the vehicle. Please check
the local regulations concerning the installation of televisions into the motor vehicles. Some
countries may have prohibition of the television installation in the motor vehicles, others
restrict the placement of the monitors.

Do NOT watch television while driving!

Do not open or remove the cover of the receiver, antenna or IDU unit to avoid exposure of
dangerous voltage.

The ANT1500 system is specifically designed for use as it comes, shipped with housings and
unit covers intact.

Any attempt to modify or to retrofit this product or its components will void the
warranty and may be hazardous.

Consumers should not attempt repairs to any components in the system! There are no
user accessible parts.
Only qualified and authorized service personnel should repair damaged or non-operational

equipment.
Repairs to any component of the antenna should be performed only by the company
MOLPIR, or by the technicians authorized by this company. Evidence of unauthorized repairs
or tampering will void the warranty. To avoid fire or electrical shock by the receiver, indoor
unit, or other components, do not expose them to rain or moisture (this does not include

the weatherproof antenna). The IDU unit and receiver’s ventilation openings must not be

tampered, covered or obstructed.
Make sure that the power to antenna is ALWAYS disconnected from the power source
BEFORE connecting or removing any cables from the IDU.

Most television, audio and video programming is protected by copyright and other

laws. Recording or rebroadcasting of paid or other public display may violate such

laws and result in civil and/or criminal penalties.

~ 4 ~

Consumer is responsible for subscribing to a satellite broadcast service and for all

subscription costs. Unauthorized decoding of broadcast signals may violate

applicable laws and result in civil and/or criminal penalties. Consumer is also

responsible for receiving and maintaining any and all product approvals required

under applicable laws and regulations.

We tried to make this manual user friendly and helpful. It is important that only qualified

technicians install the product.

This manual is subject to change without notice.

ANT1500 is innovative antenna system that provides live satellite TV to a vehicle, while in

motion. This manual provides basic instructions on how to install the antenna and its basic settings.

Before the installation of the antenna on the vehicle, please mark here the serial number

and product code in case of the warranty claim or consulting the solution of the possible

problems:

1.1. Installation and safety instructions for the user

Before the installation or operation of the antenna system ANT1500 please read

carefully this manual. Following the instructions is important in order to ensure safe
and proper installation and setting of the system.

Please temporarily keep the shipping cardboard and packing material of the antenna in

case, that it will be necessary to return the system for the maintenance or repair, at
least for as long as the product is under warranty. It will facilitate you any future
packaging for transport.

Follow all instructions and warnings and pay attention to warning messages in this

manual.

In case of the use of satellite broadcasting services directly to the customer (Direct

Broadcast Satelite - DBS) or using paid services, must be this services activated before
starting the installation of ANT1500.

Components for installation of antenna ANT1500 supplied in your kit will be suitable for

almost any roof rack design. However, some of the vehicles with bigger support tubes
may not be compatible with the provided installation kit

In order to avoid harmful interference, install the antenna as far as possible, from any

other radio / 3G / 4G antenna on the vehicle.

To avoid injury, the antenna must be always handled by two people when moving or

lifting.

Antenna (ODU)

Serial number #

Component number #

Component number and serial numer are placed on the bottom part of the antenna

Internal unit (IDU)

Serial number #

Component number #

Component number and serial number are placed on the bottom part of the IDU unit

~ 5 ~

Thoroughly inspect the roof rack of a vehicle, to ensure, that it can withstand the

dynamic load of antenna with 32 kg. Before assembly inspect, that the roof rack is in
good condition. For adjusting and fixing the mounting brackets seek the assistance of
technicians to keep safety and safe operation of the vehicle.

When the antenna ANT1500 is properly mounted, it increases vehicle height by at least

26.5cm above the roof of the vehicle. This includes a minimum 2.5cm gap between
atenna and roof of the vehicle necessary for air circulation, plus the height of the
antenna itself 24cm. Be aware of the new vehicle height with the antenna mounted
above the roof rack. Be careful when driving through underpasses, when underground
parking and other areas of the reduced underpass.

1.2. Set Top Box Compatibility (STB)

Some STB are more sensitive than the others and may cause a degradation in performance
during marginal conditions, such as heavy rain, heavy snow and also when it is partially
blocked the view to the satellite („Line of sight“ (LOS)). STB model should be selected to
ensure the compatibility of the selected SAT receiver with antenna. To achieve the best
quality picture it is appropriate to consult with the technical support from MOLPIR the type,
model STB, as well as initial setting of STB and IDU unit of the antenna itself.

1.3.Reception of mobile satellite TV

Antenna ANT1500 is designed to receive satellite television via the Direct Broadcast
Satellite (DBS) satellites, located 35,000 km in space. This system requires a clear view to
the skies above the equator to maximize the signal reception. Other factors, such as
satellite coverage area, elevation angle, and weather also contribute to the signal quality.

Satellite coverage

You must be located within the satellite’s coverage area for proper reception. As you begin

to travel outside of this coverage area, the signal becomes weaker.

Line Of Sight (LOS) interruption

The SR1500 antenna needs a clear line of sight (LOS) or view to the satellite for

uninterrupted reception. Objects such as buildings, mountains, bridges, tunnels and trees

that block this view will cause a loss of signal. The signal will, however, be quickly restored

once the antenna has a clear LOS again.

Line of Sight – The system ANT1500 needs to have a clear line of sight (LOS) - line of

sight (LOS) to the southern sky , in order to receive the satellite signal. Placing the antenna

too close to other equipment on the roof, such as A/C units, may interfere with the signal

reception. Use the chart below to determine the minimum distance needed between the

antenna and the the potential LOS blockage.

Blockage height (mm)

Minimum distance (mm)

200

560

250

710

300

840

350

990

400

1120

~ 6 ~

If the vehicle is parked, rain, morning dew, or snow in winter may accumulate on the
antenna. This may cause interference to satellite signal. When the vehicle is in motion
any standing water should be drain down the antenna and interference should cease.
Clean the antenna cover with a clean soft cloth if necessary. Some anti-water products
are intended, to prevent the accumulation of water, snow and dew on the cover of the
antenna. If you will use them, you will avoid these conditions.

1.4.System overview

Antenna ANT1500 provides live satellite TV in a vehicle while in motion as well as while
being stationary. Antenna is suitable for installation on any vehicle. It includes the actual
roof antenna (ODU), antenna control unit (IDU), necessary cables and installation material.
Antenna is designed, determined and robust enough for operation on the roof of the vehicle
for.

Antenna ANT1500 is available in two versions:

Uni Pol/Single polarization - (one cable connection) antenna has one output and

thus provides output signal only in one polarization (HORIZONTAL or VERTICAL) and
that either in Low or High band

Dual Pol antenna has three outputs and thus provides output signal in HORIZONTAL

and VERTICAL polarization and in Low as well as High band.

According to the selected version will result from antenna into the vehicle interior 1, 2
or 3 coaxial cables.

IMPORTANT: ANT1500 Outputs, which are not in use, must be blinded by TNC-BLEND
(optional equipment of Antenna).

1.5. Power supply requirement

Electrical consumption of the components of antenna ANT1500 is described in detail

below.

Standard energy consumption is important for the general dimensioning of the power

system of the vehicle.

Maximum power consumption is determined according extreme conditions, where the

antenna uses full power of the DC engine to rotate the platform of antenna and also
running of the stepper engine tilt of active panel of the antenna.

It is necessary, that the total power consumption before planning antenna took into

account another consuption for peripherals . Actual installation should be made by
those skilled in the art.

~ 7 ~

LB

HB

CTR

In the case of DC/AC converter for accessories of SAT TV system (e.g. set top box with

power supply 230V AC) it necessary to use converter with real sine wave, to avoid
possible damage of the connected devices and possible interference of the TV signal.

Chart 1: Electricity consumption of the particular components

Component

Consumption

Standard

Maximum

Antenna

50W

110W

IDU

8W

20W

STB, standard

10W

25W

1.6. Antenna components

Antenna ANT1500 is antenna for receiving of the SAT TV signal in the whole Ku band

with automatic tracking of the selected satellite.

Version of Uni Pol antenna provides optionally receiving of the SAT TV signal

in HORIZONTAL or VERTICAL polarization and that either in LOW or HIGH band.

Version of Dual Pol antenna provides simultaneously HORIZONTAL and VERTICAL signal

of SAT TV in the selected band (LOW/HIGH) and at the same time signal of the opposite
polarization in the complementary range.

At the appropriate output connectors are following signals (band/polarization):

LV HH LH if is on LV then it is on HH and on LH
LH HV LV if is on LH then it is on HV and on LV
HV HH LH if is on HV then it is on HH and on LH
HH HV LV if is on HH then it is on HV and on LV

Dual Pol version provides simultaneously the signals on three output connectors.

1.6.1 Exterior unit of Antenna – ODU

ODU unit of Antenna ANT1500 provides mechanics, electronics and

even its connection a waterproof cover against the weather (outer

plastc cover). Mounting of the antenna is expected to be on a vehicle

rack. Antenna is connected with one, two or three coaxial cables (according the versions of

the antenna) to the devices installed in the interior of the vehicle.

ODU unit includes following key components:

Rotating platform, that includes:

o Mechanism of the antenna platform rotation
o Receiving antenna panel (Phased Array Antenna)
o Mechanism for tilting of the receiving antenna panel
o Control unit
o Polarization antenna
o GPS, motion sensor and main CPU unit with integrated RSSI tuner

Rotating antenna connector (central connector)
Radio frequency transparent cover resistant to weather conditions Antenna base
Antanna base (static platform)

~ 8 ~

1.Control of
azimuth

engine

2.Azimuth
engine/

rotation

3.Two-axis
gyroscope

4.Receiving
panel

5.Rotating
platform

6.Static

platform

7.LNB

and Rx Pol

Control

8.Elevation
engine/

tilting

9.Connector
s

10.Rotary
connector

11.Static

dual BDC Box

12.GPS

13.RSSI
tuner

14.CPU

Main antenna components are displayed on the picture below:

Chart 2: Antenna components

Component

Description

1

Control of the azimuth
engine

Control unit of the azimuth engine

2

Rotation engine of antenna with geared belt

3

Block of the gyroscope and inclinometer ensures directioning of the antenna
panel to the selected satellite and during the breakdown of the reception
of the satellite signal.

4

Reception panel of the

antenna

Reception panel „Phased Array“ consist of multi-layer structures with low
signal loss. Has orthogonal configuration for reception
in HORIZONTAL/VERTICAL signal polarization.

5

Rotating platform

It contains all of the antenna and is connected to the static platform through
the central bearing coaxial cable connector.

6

Static platform

Base of the whole antenna, which carries the rotating part of the antenna,
upper cover and terminal box of the connector and four installation fixing
consoles.

7

LNB and Rx Pol Control

LNB converter – changes frequency of the received signal to IF band

8

Elevation engine/tilting

Engine of the setting the tilting of receiving panel of antenna with geared
belt.

9

Connectors

Coaxial TNC connectors with external thread:

ANT1500 Dual Pol – has 3 TNC connectors

~ 9 ~

- CTRL – power supply of the antenna 30V DC, control signals and primary

TV signal

- High band – TV signal in High band and in opposite polarization as

primary TV signal

- Low band – TV signal in low band and in opposite polarization as primary

TV signal

On CTRL connector is connected IDU unit, that determines (manages) what
signal will be on CTRL output. It may be H or V polarization and low or high
band.
Outputs Low band (LB) and High band (HB) have always opposite
polarization, as it is selected on Ctrl output. For more details please see the
configuration of the polarization on the page 36.

ANT1500 Uni Pol – has only one TNC connector

- CTRL – power supply of the antenna 30V DC, control signals and primary

TV signal

10

Rotary connector

Rotary connector ensures the transmission of VF signal from rotating
platform to the base of the antenna and the transmission of the power
supply from the base of the antenna for electronical components and
stepper motor of the elevation placed on the rotating platform and the
transmission of the control signals.

11

Static dual BDC Box

Device, that uses MMIC technology to distribute the output signal of the
antenna on the particular output ports.

12

GPS

Specifies the geografic position of the antenna. The angle of inclination of
the antenna panel (elevation angle) is calculated from the GPS data.

13

RSSI Tuner

Satellite DVB tuner with RSSI detector level of the received signal, that is
used to track selected satellite in the sky during motion.

14

CPU

Automatically controls the antenna as a whole

15

Cover

(not shown) the upper cover of the antenna is made off a radio transparent
plastic material, which provides sufficient protection from weather and
mechanical damage of the antenna panel and all components on the
rotating platform. Is connected to the static platform and provides
additional stiffness of the whole structure of the antenna.

1.6.2. Interior unit of Antenna – IDU

Interior control unit (IDU) – control of the antenna (code: AMR-IDU-M003)
Interior unit(IDU) supplies the antenna and gives commands (selection of
satellite, polarization, bandwidth, ...). This device enables the selection of

LB

HB

CTRL

~ 10 ~

Satellite antenna for mobile application 10,70-12,75GHz; 24cm; dual polarization

satellite, from which will be received the signal. IDU is further connected to satellite receiver
(STB) in interior of the vehicle.

Pos.1

Pos.2

Name

Code

pc

1

Satellite antenna

1 2

IDU Basic M003

AMR-IDU-M003

1

3

Set of cabling for antenna with dual polarization

AKT2000289

1

4 Cable of satellite antenna RG58 with TNC connectors - 12m

CBM1000010

1

5 Cable of the satellite antenna RG59 with TNC/F connector-12m

CB101738

2 6

Power supply cabling of the satellite antenna 2x12AWG - 6m

CBM0000165

1 7

Cable of the satellite antenna RG59 with F connectors – 1m

CBM0000021

1 8

Automotive blade fuse 15A Mini

3WA02515A

1

9

Installation kit of the IDU unit

COT1000000

1

10

Bracket of the IDU unit

2 11

Screw M3x7,5mm

4 12

Spring washer D3mm

4

13

Installation kit of the antenna

AKT0000048

1

14

Rubber antenna washer

MPP0000027

8

15

Bottom washer

MMP1000197

4

16

Blanking plug

MPP0000048

8

17

Washer spacer 18mm

MPP0000111

4

18

Screw M6x40mm with conical head allen

MFS0000100

8

19

Screw M5x45mm with cylinder head - allen

MFS0000115

8 20

Allen key S4

CCS0000002

1

~ 11 ~

1.6.4. Package content ANT1500 - SP

Satellite antenna for mobile application 10,70-12,75GHz; 24cm; single polarization

1.7. Unpacking, inspection and preparing of the installation

Before you will install the system, check the supplied equipment and examine its content
and completness after delivery.
Antenna system ANT1500 has several components. Check and make sure the completness
of the delivery of your system, before you start with the installation. Content of the basic
set is mentioned in the chart „Package content ANT1500“.

Check if the delivery is not damaged when receiving the goods:

Any damage of the transport packaging or components must be immediately after

delivery, no later than in three working days, documented with the pictures and
warranty claim has to bes end to the company MOLPIR.

Unpacking, inspection of the delivery of the antenna components as well as its assembly

perform in the interior.

Supplied goods store in approriate storage conditions, do not expose to humidity, rain,

snow, as well as excessive sunlight and high temperature

Pos.1

Pos.2

Name

Code

pc

1

Satellite antenna

1

2

IDU Basic M003

AMR-IDU-M003

1 3

Cable of satellite antenna RG58 with TNC conectors - 12m

CBM1000010

1

4 Power supply cabling of the satellite antenna 2x12AWG - 6m

CBM0000165

1

5 Cable of satellite antenna RG59 with F connectors – 1m

CBM0000021

1 6

Automotive blade fuse 15A Mini

3WA02515A

1 7

Installation kit of the IDU unit

COT1000000

1 8

Bracket of the IDU unit

2

9

Screw M3x7,5mm

4

10

Spring washer D3mm

4

11

Installation kit of the antenna

AKT0000048

1

12

Rubber antenna washer

MPP0000027

8 13

Bottom washer

MMP1000197

4 14

Blanking plug

MPP0000048

8 15

Washer spacer 18mm

MPP0000111

4

16

Screw M6x40mm with conical head allen

MFS0000100

8

17

Screw M5x45mm with cylinder head - allen

MFS0000115

8 18

Allen key S4

CCS0000002

1

~ 12 ~

1.8 ANT1500 main system parameters

Parameter

Description

Mechanické

Antenna dimensions (ODU)

115 x 90 x 24 cm (length x width x height)

Antenna weight (ODU)

32 kg

IDU dimensons

18 x 23 x 7 cm (length x width x height)

IDU weight

1 kg

Electrical

Antenna G/T

10 ± 1 dB/K @ 30° elevation

Band frequency

Ku, full band 10.7 – 12.75 GHz

Power supply

10 - 30V DC / 110 W

Average consumption

50W

Maximum consumption

110 W

Polarization

Dual-Pol version

V/H or RHCP/LHCP simultaneously on 1,5GHz band, 3 simultaneous connections

Antenna performance

Elevation, angle range

Set automatically in the range 10° ~ 80°

Azimuth, angle range

Set automatically, continuos 360°

Max. speed of chaging
azimuth

60°/second

Polarzation, angle range

Set automatically from -180° to +180°

Positioning of the satellite

< 1 minute, fully automatic with integrated GPS

Re-determination of the
satellite position

< 10 seconds (when LOS is blocked < 2 minutes), integrated gyro

Satellite services

Frequency

Whole Ku-band

Supports satellite from

EIRP ≥50 dBW

Supports regional DTH / FTA
services

For example:

Middle East

OSN, FTA channels on NileSat, BADR, Arabsat and others.

Europe

FTA on Astra&HotBird, Freesat, BSkyB, SKY IT, Canal+, NTV+, Digiturk and

others .

Latin America

Dish-MX, Sky-BR, Claro, DTVLA and others.

Asia/Pacific

Dish-TV, Airtel, Tata Sky DD, TrueVisions, Foxtel and others .

North America

DISH® Network, Direct-TV, Bell-TV

Africa

DSTV in selected regions, ZAP, Canal+

Electric interface

Dual-Pol version

3 x TNC, 50Ω connectors

Operating conditions

Temperature range

-25°C to +55°C (-13°F to + 130°F)

Land speed of the vehicle

Up to 350 km/h

~ 13 ~

1.9 Main dimensions

Following figures shows the dimensions of the antenna ANT1500 (Dual Pol / Uni Pol).

2 Installing the Antenna on a vehicle roof

For selecting the location on the rooftop consider these guidelines:

Select flat surface
Do not place antenna close to mechanical blockage (A/C unit etc…) to not block

satellite view

Do not place antenna close to 3G/4G antennas to avoid electromagnetic

interferences

Determine where the antenna cables will enter into vehicle´s interior. This is

usually in the cab area or close to place, where the power source is located. When
placing the antenna on the roof, side of antenna with TNC connectors should be
facing the point of entry of cables into vehicle.

Connector position facing cable entry point to vehicle

Side view

Bottom view

~ 14 ~

Chart 3 – Material for installation of antenna on rooftop (*optional)

1

2 3 4

Roof preparation for mounting can be done by customer, using a kit of bracket
crossbars 0810284-xxx (xxx=width of rack in mm, optimal for this type of roof –
reccomended by MOLPIR). Distance of axes „D“ is 950mm – see Fig. on page 15

2.1 Accessories / tools necessary:

Permanent marker 1x
Latex gloves 10x
Accu-screw driver 1x

Iron drill Ø 3 mm 1x
Iron drill Ø 7 mm 1x

Sheet metal drill 1x
Screw driver Torx 30 1x
Locating plug (clench nut) Ø7mm 4x
Abrasive paper Nr.80 1x
Agent WD40 (or similar) 1x
Degreasing agent 1x
Polyuretan glue for glass 1x
Glue gun 1x
Screw 6x40mm (assistant) 2x
Masking tape 48mm (min) 1x
Cleaning rag
Paper rag

2.2 Installation of Roof rack on vehicles roof

Pos.

Item

Code

pcs

1

Satelite antenna; Single Polarisation; whole Ku band

1

1*

Satelite antenna; Dual Polarisation; whole Ku band

2

Antenna bracket ANT1000 for Mercedes Setra 2010>

2

2*

Antenna bracket ANT1000 for Neoplan CityLiner; Mercedes Sprinter

2*

Antenna bracket ANT1000 for Mercedes Setra line 500

3 Base plate of antenna bracket ANT1000

4 4 Screw M6x16

24

~ 15 ~

Fig.6.3

Driving direction

950mm

Fig.6.4.1.

„O“

„D“

 Optional

2.3 Location of antenna on a vehicle´s roof

Note: If necessary, it is possibile to place antenna

across to driving direction, but still is necessary to
keep facing of TNC connectors (coax cable output) to
the back of vehicle!

2.4 .Assembly order of antenna´s bracket

Choose suitable antenna bracket according vehicle type and roof construction (tab.2,
pos.2). Mark axe of roof „O“ in driving direction on expected place of antenna and
locate crossbars of bracket in axe distance „D“ of 950mm (according Fig. 6.3).

2.4.1 Use permanent marker to mark future location of feet of bracket (Fig. 6.4.1.).

Attachment points for bracket crossbars

~ 16 ~

Fig 6.4.2.

Fig 6.4.3.

Fig 6.4.4.

2.4.2 To secure position of bracket to the roof, drill hole Ø 7 mm (drill Ø 3 mm first, if

necessary) through foot and insert locating pin (clench nut Ø 7). Then drill rest of
holes, into this way secured foot, see Fig. 6.4.2.

2.4.3 To avoid a change of crossbars, mark on them driving direction and order of

crossbars (Fig. 6.4.3.).

2.4.4 If there is no entrance hole into interior for cable on the roof, you have to make it.

Place antenna on crossbars and lead cable that way not to be broken and not to be
too long. Mark point, where coax cable will enter into interior. This point supposes
to be close to the TNC connector of antenna, but should allow to make smooth radius
of cable entering to interior. In this point drill hole Ø 3 mm and then hole with
gradual drill (Fig. 6.4.4.)

~ 17 ~

Fig. 6.4.5.

Fig. 6.4.6.

Fig 6.4.7.

2.4.5 Scratch contacting surface of roof with antenna bracket using abrasive paper (Fig.

6.4.5.).

2.4.6 Clean mounting area using pressured air.

2.4.7 Clean contacting surface using degreasing agent. Clean also hole for cable entrance.

(Fig. 6.4.7.).

~ 18 ~

Fig 6.4.8.

Fig 6.4.9.

Fig 6.4.10.

2.4.8 Using paper painters tape (wide min. 48mm) border contacting surface cca 10 mm

from marked edge. Also make border with tape around entrance cable hole. (Fig.

6.4.8.).

2.4.9 Apply required quantity of glue on whole surface, which is bordered this way. (Fig.

6.4.9.).

Note: because of fastness of glue hardening, we recommend phased mounting of

brackets: finish first, then start second one.

2.4.10 Place bracket to the glue and press vertically to the roof (Fig. 6.4.10.).