moll T 7, T 7 XL Operating Manual

moll T 7 / T 7 XL

Operating Manual

with Safety Instructions

and EC Declaration of Conformity

06. 2018

Electrically adjustable desk

for the living area

GB

2

Safety Instructions

It is essential to read this operating instruction thoroughly before

commissioning the table.

Caution:

The sit-stand table may be used only for its intended use as a writing

and working table for the living area.

Caution: This sit-stand table is not designed for continuous operation.

The table top height can be adjusted without interruption for no longer

than the operating time indicated in this manual(2 min on / 18 min off).

Caution:

This unit may only be operated with a mains voltage of

220-230 V / 50-60 Hz.

Danger:

Please use only the supplied power cable! Make sure that the power

cable is not damaged. Operating the sit-stand table with a damaged

power cable is prohibited! It must be replaced to prevent from hazards

of electric shock.

Caution:

If the product is visibly damaged, makes unusual noises or causes

odours, it may not be assembled or used!

Danger:

Using this table is only permitted in dry rooms. Protect the table frame

and in particular all electrical components on the table from moisture,

dripping or splashing water!

33

Safety Instructions

Danger:

This unit can be used by children aged 8 years and above and by persons

with reduced physical, sensory, or mental capabilities, or lack of

experience and knowledge, if they are supervised or have been

instructed in the safe use of the unit and understand the hazards

involved.

Danger:

Children must not play with the device!

Cleaning and user maintenance shall not be carried out by children

without supervision .

Danger:

Do not open the motor control unit under any circumstances.

There is a danger of electric shock.

Electrical equipment may only be opened or replaced by trained and

qualied personnel.

Danger:

There is a danger of crushing when changing the table top position!

You must therefore ensure that no persons or objects are located in the

hazardous area or reach into it.

Please keep this operating manual for future reference !

It is a part of the table and contains important safety informations.

When the table is sold, rented out or otherwise passed on to another

party, it must be handed over with this operating manual.

4

Check for completeness

rear side with power management

2

1

5

2x

moll T7 / T7 XL

06. 2018

5

Safety Instructions

To avoid crushing or shearing hazards, the desk with its moving parts must

keep a minimum distance of 50 cm to adjacent objects such as furniture,

building parts etc.

When adjusting the table top height, the user must make sure that nobody

can be injured and no objects can get damaged. The desk must not

collide with fixed objects , because it otherwise may tip over!

Before adjusting the table top height, please move away chairs, containers

etc. to avoid possible collisions.

Solid objects are usually detected by the optional collision protection, but

the danger of crushing for persons still exists! The collision protection

protects the system, NOT persons!

5

0 c

m

50

c

m

6

Levelling the desk

Note

The desk must be aligned horizontally with the adjustment plates.

Thus, the best stability is achieved.

7

Moving the desk

To move the desk, simply raise the front. Now it can be easily moved back

and forth on the integrated castors.

Note

1.

2.

8

Make sure that the cable length is also sufficient when the tabledesk

is in the top position. Route the cable so that it is not likely to trip over it.

Danger!

Should the power cord become damaged, unplug the desk immediately!

Caution

Mains voltage:

220 - 230 V / 50 - 60 Hz

The key switch protects against unauthorized height adjustment of the table.

When the key is removed in the „off“ position, the table can not be adjusted

accidentally or on purpose.

Note

9

ONOFF

Caution

Caution! Remove key during use.

Please do not leave the key in the lock - risk of injury!

10

Upward desktop movement

When adjusting the table top height, please make sure that the

table movement will not get blocked (e.g. by window sills, chair

armrests, file cabinets etc.)and that no persons are located in

the hazardous area or will reach into it.

Note

As delivered, the desk's height adjustment requires two-hand operating for

safety reasons. The button on the left side of the table and the "UP" or

"DOWN" button must be pressed simultaneously while the lock switch is in the

"ON" position (see page 9). The two-hand operating can be switched off

permanently, this allows desk operation without actuating the left button

(see page 12).

11

Downward desktop movement

Maximum operation time: 2 minutes of continuous operation, the control

unit is automatically disabled for the next 18 minutes!

The operation duration is then automatically limited to this period.

This prevents the table drive from overheating.

Note

12

N

Enabling single-hand operating

The table can be permanently set to single-hand operating so it can be

adjusted using the "UP" and "DOWN" keys without pressing the left

button. Please disconnect the mains plug from the socket before

changing this setting! Remove the plastic cover on the right bottom

side of the desk (4 screws, see picture) to get access to the toggle

switch.

Reinstall the plastic cover and connect the desk to mains.

Important safety note

The two-hand operating is a safety feature of the desk! The conversion to

single-handed operating is at the user's own responsibility!

Toggle switch towards the front side

of the desk = Two-hand operating

Toggle switch towards the back side

of the desk = Single-hand operating

13

Container-stop / Shelf-stop positions

Container-stop and

shelf-stop position

These two functions can be used to

limit the range of movement of the

sit-stand table (e.g. if a file cabinet

is located under the sit-stand table).

A container-stop position can be set

only in the lower half of the

movement range, a shelf-stop

position only in the upper half of

the movement range. If a container

stop position is set, it is used as the

lower end position, while a

shelf-stop position corresponds to

the upper end position of the

movement range.

To activate a container- or shelf-stop position, follow these steps:

1. Move the sit-stand table to the position that you want to define as a new

container- or shelf-stop position.

2. Press the button on the left side and the UP and DOWN buttons simul-

taneously for 10 seconds. The control unit confirms the successful

activation with a double-click sound.

To deactivate a container- or shelf-stop position, follow these steps:

1. Move the sit-stand table to any position in the lower half of the movement

range to deactivate the container-stop , or in the upper half of the

movement range for the shelf-stop position.

2. Press the button on the left side and the UP and DOWN buttons simul-

taneously for 10 seconds. The control unit confirms the deactivation with a

single click sound.

14

Height adjustment

Recommended adjustments

The desktop height is infinitely adjustable from 56 cm to 118 cm

(with height adapter from 66 cm to 128 cm - see page 20)

127 cm

135 cm

143 cm

151 cm

159 cm

167 cm

175 cm

183 cm

191 cm

~56 cm

~59 cm

~63 cm

~66 cm

~69 cm

~72 cm

~75 cm

~79 cm

~82 cm

~80 cm

~85 cm

~90 cm

~96 cm

~102 cm

~108 cm

~113 cm

~118 cm

~124 cm

10 cm

sittingstanding

±

cm

Opening the drawer

press the center of the drawer front

and the drawer opens

press the center of the drawer front and close

the drawer until it engages with a clicking sound

Closing the drawer

15

max. 6 kg

16

Power-Management

with integrated power outlets

Please make sure that you plug in the connectors and power supplies

so that they are not damaged and that no wires get pinched when the

drawer is closed.

17

18 19

Cable feedthrough

Accessories

Flexlight

flexible LED desklight

moll L7

flexible LED desklight

20

Accessories

Height adaptor to increase the desktop height by 10 cm

The desktop height with this adaptor is adjustable from 66 cm to 128 cm

2x

QI Wireless Charger

This table can be upgraded with a QI charger for wireless charging of

electronic devices. Detailed information can be found on our website or can

be obtained from your dealer.

21

FAQ

The desktop height can not be adjusted:

• Is the power cord correctly plugged into the desk and the power outlet?

• Is the electrical power outlet working?

• Has the maximum operation time been exceeded (see page 11)?

Strange noises or smoke:

• Immediately unplug the power cord and call for service!

Slow upward movement:

• The maximum lifting capacity is exceeded, reduce the weight.

Desk stops during upward or downward movement before it has reached

the end position:

• Container-stop and / or shelf-stop function is active (see page 12).

Desk stops during upward or downward movement and changes drive

direction:

• The desk ran against an obstacle and the collision protection has been

triggered. Eliminate the cause of the collision!

Cleaning and care:

We recommend a damp cloth and a mild household cleaner for regular

cleaning of the table surface.

Please do not use scouring agents or abrasive cleaners!

22

Technical Data

Desktop size (corpus) T7: 115 x 75 x 9 cm

Desktop size (corpus) T7 XL: 150 x 75 x 9 cm

Desk height (infinitely adjustable):

without adaptor 56 - 118 cm

with adaptor (optional) 66 - 128 cm

Drawer internal dimensions:

T7: W 44,0 / D 30 / H 4 cm

W 35,5 / D 30 / H 4 cm

T7 XL: W 44,0 / D 30 / H 4 cm (2x)

W 12,5 / D 30 / H 4 cm (2x)

Max. drawer load: 6 kg

Max. loading capacity T7: 60 kg

Max. loading capacity T7 XL: 50 kg

Lifting speed: 38 mm / s

Noise level: < 60 dB(A)

Temperature range for operation: 0° bis +30° C

Temperature range for storage: -40° bis +50° C

Humidity for operation: 5% to 85% (non-condensating)

Humidity for storage: 5% to 90% (non-condensating)

Protection class I

IP class IP 20

Max. duty cycle: 10% ( 2 min. on / 18 min. off )

Nominal voltage: 220 - 230 V / 50 - 60 Hz

Drive / control 288 W

Power-Management (optional), total maximum load:

IEC type »F« (e.g. Germany, ...):

IEC type »V« (e.g. France, ...):

IEC type »G« (e.g. U.K., ...):

IEC type »L« (Italy):

IEC type »J« (Switzerland):

IEC type »I« (e.g. China, ...):

max. 3200W

max. 3200W

max. 2600W

max. 2200W

max. 2300W

max. 2000W

WEEE-Reg.-Nr.

DE 78284755

23

EC Declaration of Conformity

Copyright by moll220 823 0706.2018

moll Funktionsmöbel GmbH

Rechbergstraße 7

D 73344 Gruibingen

Tel. [phone]

[e-mail]

www.moll-funktion.de

Please keep this operating manual for future reference !

It is a part of the table and contains important safety informations.

When the table is sold, rented out or otherwise passed on to another

party, it must be handed over with this operating manual.

GB