Page 1
INSTALLATION INSTRUCTIONS
Terminated with F/UTP cable .............................................................................................page 1-3
Terminated with S/FTP cable .............................................................................................page 4-5
Terminated with U/FTP cable .............................................................................................page 6-8
Shielded DataGate Jack
1. Termination Tool
110 termination tool set on low impact.
TERMINATED WITH F/UTP CABLE
2. Preparation and termination (F/UTP)
2a. Slide rear can and plastic cable clamp on to cable.
2b. 180° cable entry.
2c. 90° cable entry.
2d. Remove can cut-out for 90° cable entry.
MOLEX PREMISE NETWORKS
Molex Premise Networks
Corporate Headquarters
Tel: 1 866 733 6659
www.molexpn.com
AS-18700-002, Rev C Form # 315-234 Rev. Date: July 2008 SAP # 187000294
Doc. #
European
Headquarters
Tel: 44 (0) 1489 572111
www.molexpn.co.uk
This information is correct as at the time of publication, specifications are subject to change.
Headquarters
Tel: 61 3 9971 7111
www.molexpn.com.au
Pac Rim
Molex
Incorporated
Tel: 630 969 4550
www.molex.com
1
Page 2
INSTALLATION INSTRUCTIONS
Shielded DataGate Jack
2e. Remove 100mm of cable sheath. Cut central separator back to sheath.
Cut cellophane wrap back to sheath. Wrap foil around cable.
2f. Wrap drain wire around foil and tighten, leaving a length of drain wire available
for wrapping around rear can cable clamp.
100mm
Untwist Max 6mm
Cut
Wrap foil around
cable
2g. Wiring Map.
2h. Terminate the jack before inserting it in front can.
2i. Ensure that the cable sheath is maintained up to the connector.
2j. Once terminated, the stuffer cap must be fitted to the connector.
MOLEX PREMISE NETWORKS
Molex Premise Networks
Corporate Headquarters
Tel: 1 866 733 6659
www.molexpn.com
AS-18700-002, Rev C Form # 315-234 Rev. Date: July 2008 SAP # 187000294
Doc. #
European
Headquarters
Tel: 44 (0) 1489 572111
www.molexpn.co.uk
This information is correct as at the time of publication, specifications are subject to change.
Headquarters
Tel: 61 3 9971 7111
www.molexpn.com.au
Pac Rim
Molex
Incorporated
Tel: 630 969 4550
www.molex.com
2
Page 3
INSTALLATION INSTRUCTIONS
2k. Ensure cables are trimmed off flush with IDC, if not use side cutters to remove excess
cable after termination.
3 Fitting Can and Securing Cable (F/UTP)
3a. Slide the rear can over the front can. Ensure that the two halves are latched
together securely.
3b. Ensure that sufficient foil and drain wire makes contact with rear metal collar.
Trim off excess foil.
Shielded DataGate Jack
3c. Tighten the drain wire over the metal cable collar to maintain shield continuity.
3d. Secure the cable with the plastic cable clamp, placed and tightened over the metal
cable collar.
MOLEX PREMISE NETWORKS
Molex Premise Networks
Corporate Headquarters
Tel: 1 866 733 6659
www.molexpn.com
AS-18700-002, Rev C Form # 315-234 Rev. Date: July 2008 SAP # 187000294
Doc. #
European
Headquarters
Tel: 44 (0) 1489 572111
www.molexpn.co.uk
This information is correct as at the time of publication, specifications are subject to change.
Headquarters
Tel: 61 3 9971 7111
www.molexpn.com.au
Pac Rim
Molex
Incorporated
Tel: 630 969 4550
www.molex.com
3
Page 4
INSTALLATION INSTRUCTIONS
TERMINATED WITH S/FTP CABLE
4. Preparation and termination (S/FTP)
4a. Slide plastic cable clamp and rear can on to cable.
4b Remove 100mm of cable sheath.
4c. Remove foil from pairs of cable. Twist braid and wrap around the cable sheath
Shielded DataGate Jack
4d. Wiring Map.
Untwist Max 6mm
4e. Terminate cable ensuring that enough twisted braid is available to make contact
when the rear can is fitted.
4f. Ensure cables are trimmed off flush with IDC, if not use side cutters to remove excess
cable after termination.
MOLEX PREMISE NETWORKS
Molex Premise Networks
Corporate Headquarters
Tel: 1 866 733 6659
www.molexpn.com
AS-18700-002, Rev C Form # 315-234 Rev. Date: July 2008 SAP # 187000294
Doc. #
European
Headquarters
Tel: 44 (0) 1489 572111
www.molexpn.co.uk
This information is correct as at the time of publication, specifications are subject to change.
Headquarters
Tel: 61 3 9971 7111
www.molexpn.com.au
Pac Rim
Molex
Incorporated
Tel: 630 969 4550
www.molex.com
4
Page 5
INSTALLATION INSTRUCTIONS
4g. Fit stuffer cap after termination.
5. Fiting Can and Securing Cable (S/FTP)
5a. Slide the rear can over the front can. Ensure that the two halves are latched
together securely.
5b. Wrap braid around the metal cable collar to maintain shield continuity.
Shielded DataGate Jack
5c Secure the cable and braid with the plastic cable clamp, place and tighten over the
metal cable collar.
MOLEX PREMISE NETWORKS
Molex Premise Networks
Corporate Headquarters
Tel: 1 866 733 6659
www.molexpn.com
AS-18700-002, Rev C Form # 315-234 Rev. Date: July 2008 SAP # 187000294
Doc. #
European
Headquarters
Tel: 44 (0) 1489 572111
www.molexpn.co.uk
This information is correct as at the time of publication, specifications are subject to change.
Headquarters
Tel: 61 3 9971 7111
www.molexpn.com.au
Pac Rim
Molex
Incorporated
Tel: 630 969 4550
www.molex.com
5
Page 6
INSTALLATION INSTRUCTIONS
TERMINATED WITH U/FTP CABLE
6. Preparation and termination (U/FTP)
6a. Slide plastic cable clamp and rear can on to cable.
6b. Remove 100mm of cable sheath.
6c. Remove 3 of the 4 foils from the cable pairs. Unwrap the foil from 1 pair in
preparation for wrapping around the cable sheath.
The dark side of foil is the non-conductive side. Ensure that this side faces the cable
sheath when wrapped. The silver colour is the conductive side and must face outward.
Shielded DataGate Jack
6d. Wrap the foil around the sheath with the conductive side of the foil facing outward.
Trim off excess foil.
MOLEX PREMISE NETWORKS
Molex Premise Networks
Corporate Headquarters
Tel: 1 866 733 6659
www.molexpn.com
AS-18700-002, Rev C Form # 315-234 Rev. Date: July 2008 SAP # 187000294
Doc. #
European
Headquarters
Tel: 44 (0) 1489 572111
www.molexpn.co.uk
This information is correct as at the time of publication, specifications are subject to change.
Headquarters
Tel: 61 3 9971 7111
www.molexpn.com.au
Pac Rim
Molex
Incorporated
Tel: 630 969 4550
www.molex.com
6
Page 7
INSTALLATION INSTRUCTIONS
6e. Wrap drain wire around foil and tighten, leaving a length of drain wire available
for wrapping around rear can cable clamp.
Shielded DataGate Jack
6f. Wiring Map.
6g. Terminate the jack before inserting it in front can.
6h. Ensure that the cable sheath is maintained up to the connector.
6i. Once terminated, the stuffer cap must be fitted to the connector.
6j. Ensure cables are trimmed off flush with IDC, if not use side cutters to remove excess
cable after termination.
MOLEX PREMISE NETWORKS
Molex Premise Networks
Corporate Headquarters
Tel: 1 866 733 6659
www.molexpn.com
AS-18700-002, Rev C Form # 315-234 Rev. Date: July 2008 SAP # 187000294
Doc. #
European
Headquarters
Tel: 44 (0) 1489 572111
www.molexpn.co.uk
This information is correct as at the time of publication, specifications are subject to change.
Headquarters
Tel: 61 3 9971 7111
www.molexpn.com.au
Pac Rim
Molex
Incorporated
Tel: 630 969 4550
www.molex.com
7
Page 8
INSTALLATION INSTRUCTIONS
7 Fitting Can and Securing Cable (U/FTP)
7a. Slide the rear can over the front can. Ensure that the two halves are latched
together securely.
7b. Ensure that sufficient foil and drain wire makes contact with rear metal collar.
Trim off excess foil.
7c. Tighten the drain wire over the metal cable collar to maintain shield continuity.
7d. Secure the cable with the plastic cable clamp, placed and tightened over the metal
cable collar.
Shielded DataGate Jack
MOLEX PREMISE NETWORKS
Molex Premise Networks
Corporate Headquarters
Tel: 1 866 733 6659
www.molexpn.com
AS-18700-002, Rev C Form # 315-234 Rev. Date: July 2008 SAP # 187000294
Doc. #
European
Headquarters
Tel: 44 (0) 1489 572111
www.molexpn.co.uk
This information is correct as at the time of publication, specifications are subject to change.
Headquarters
Tel: 61 3 9971 7111
www.molexpn.com.au
Pac Rim
Molex
Incorporated
Tel: 630 969 4550
www.molex.com
8
Loading...