Moldex 5010 User Manual

Date Printed: 12/14/2018

Safety Data Sheet

www.rustoleum.com

1. Identification

Product Name: MX MOLD KILLER 32 oz SPRAY Revision Date: 12/14/2018

Product Identifier: 5010 Supercedes Date: 10/13/2017

Recommended Use: Disinfectant/Alkaline

Page 1 / 5

Supplier:

Preparer: Regulatory Department

Emergency Telephone:

Rust-Oleum Corporation
11 Hawthorn Parkway
Vernon Hills, IL 60061
USA

24 Hour Hotline: [phone]

Manufacturer:

2. Hazard Identification

Classification

Symbol(s) of Product

Signal Word

Warning

Possible Hazards

3% of the mixture consists of ingredient(s) of unknown acute toxicity.

GHS HAZARD STATEMENTS

Eye Irritation, category 2 H319 Causes serious eye irritation.

Rust-Oleum Corporation
11 Hawthorn Parkway
Vernon Hills, IL 60061
USA

GHS LABEL PRECAUTIONARY STATEMENTS

P264 Wash hands thoroughly after handling.

P280 Wear protective gloves/protective clothing/eye protection/face protection.

P305+P351+P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present

P337+P313 If eye irritation persists: Get medical advice/attention.

and easy to do. Continue rinsing.

3. Composition / Information On Ingredients

HAZARDOUS SUBSTANCES

Chemical Name CAS-No. Wt.%

Range

2-(2-butoxyethoxy)ethanol 112-34-5 1.0-2.5 GHS07 H319

Ethylenediaminetetraacetic acid, tetrasodium salt 64-02-8 1.0-2.5 GHS05-GHS07 H302-318

GHS Symbols

GHS Statements

Date Printed: 12/14/2018

Page 2 / 5

4. First-Aid Measures

FIRST AID - EYE CONTACT: Immediately flush eyes with plenty of water for at least 15 minutes holding eyelids open. Get medical

attention. Do NOT allow rubbing of eyes or keeping eyes closed.

FIRST AID - SKIN CONTACT: Wash skin with soap and water. Remove contaminated clothing. Get medical attention if irritation
develops or persists.

FIRST AID - INHALATION: Remove to fresh air. If not breathing, give artificial respiration. If breathing is difficult, give oxygen. Get
immediate medical attention. Do NOT use mouth-to-mouth resuscitation. If you experience difficulty in breathing, leave the area to
obtain fresh air. If continued difficulty is experienced, get medical assistance immediately.

FIRST AID - INGESTION: Swallowing less than an ounce will not cause significant harm. For larger amounts, do not induce
vomiting, but give one or two glasses of water to drink and get medical attention. If swallowed, rinse mouth with water. If feeling
unwell, get medical attention.

5. Fire-Fighting Measures

EXTINGUISHING MEDIA: Alcohol Film Forming Foam, Carbon Dioxide, Dry Chemical, Dry Sand, Water Fog

UNUSUAL FIRE AND EXPLOSION HAZARDS: No unusual fire or explosion hazards noted. Keep containers tightly closed. FLASH

POINT IS TESTED TO BE GREATER THAN 200 DEGREES F.

SPECIAL FIREFIGHTING PROCEDURES: Water may be used to cool closed containers to prevent buildup of steam. If water is
used, fog nozzles are preferred.

Special Fire and Explosion Hazard (Combustible Dust): No Information

6. Accidental Release Measures

STEPS TO BE TAKEN IF MATERIAL IS RELEASED OR SPILLED: If spilled, contain spilled material and remove with inert

absorbent. Dispose of contaminated absorbent, container, and unused contents in accordance with local, state, and federal
regulations. Do not incinerate closed containers

7. Handling and Storage

HANDLING: Wash thoroughly after handling. Wash hands before eating. Remove contaminated clothing and launder before reuse.

Use only with adequate ventilation. Follow all SDS and label precautions even after container is emptied because it may retain
product residues. Avoid breathing fumes, vapors, or mist. Avoid contact with eyes, skin and clothing.

STORAGE: Store in a dry, well ventilated place. Keep container tightly closed when not in use.
Advice on Safe Handling of Combustible Dust: No Information

8. Exposure Controls / Personal Protection

Chemical Name CAS-No.

2-(2-butoxyethoxy)ethanol 112-34-5 5.0 10 ppm N.E. N.E. N.E.
Ethylenediaminetetraacetic
acid, tetrasodium salt

PERSONAL PROTECTION

ENGINEERING CONTROLS: Use process enclosures, local exhaust ventilation, or other engineering controls to control airborne

levels below recommended exposure limits. Prevent build-up of vapors by opening all doors and windows to achieve cross­ventilation.

RESPIRATORY PROTECTION: A respiratory protection program that meets OSHA 1910.134 and ANSI Z88.2 requirements must be
followed whenever workplace conditions warrant a respirator's use.

SKIN PROTECTION: Use gloves to prevent prolonged skin contact. Nitrile or Neoprene gloves may afford adequate skin protection.

EYE PROTECTION: Use safety eyewear designed to protect against splash of liquids.

OTHER PROTECTIVE EQUIPMENT: Refer to safety supervisor or industrial hygienist for further guidance regarding types of

personal protective equipment and their applications.

64-02-8 5.0 N.E. N.E. N.E. N.E.

Weight %

Less Than

ACGIH TLV-

TWA

ACGIH TLV-

STEL

OSHA PEL-TWA

OSHA PEL-

CEILING