Mojo Frost M1-22 Operation Manual

Download

1

800-990-9775 P 610-200-6884 SMS for support

hello@mojowater.com mojowater.com

Frost

BottleLess Water Cooler

OPERATIONS MANUAL

Model Number: M1-S22

2

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should always be followed, including:"

1. Read all instructions before using. "

2. Do not let cord hang over edge of table or counter, or touch hot surfaces."

3. To protect against electric shock, do not immerse cord, plug, or cooler in water or any other liquid."

4. Close supervision is necessary when any appliance is used by or near children."

5. Unplug from outlet when not in use and before cleaning."

6. Do not operate any appliances with a damaged cord, plug or after the appliances malfunction, or has been damaged in any manner."

7. The use of accessory attachments is not recommended by the manufacturer and may cause injuries."

8. Do not use outdoors."

9. Allow at least 2” (5cm) of space between the back of the water cooler and the wall to allow for proper air circulation."

10. Install the water cooler on a level ﬂoor. Do not install where it will be subject to direct sunlight, heat or moisture."

11. Do not install water cooler where the temperature will go below 59°F (15°C) or above 100°F (38°C)."

12. Do not plug in the power cord or turn on the hot water on/oﬀ switch when the water cooler is empty."

13. To disconnect the power cord, turn the hot water switch to “oﬀ “, then remove plug from wall outlet."

14. Always wash and dry your hands thoroughly before touching the water cooler."

15. Extreme caution must be used when moving an appliance that contains hot liquid."

16. Do not use this cooler to dispense anything other than water. (Yes, that means no beer….)"

17. Do not use with water that is micro biologically unsafe or of unknown quality.

SAVE THESE INSTRUCTIONS

18. This appliance must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock.

19. This appliance has a power cord with a grounding wire and a grounding plug. The plug must be plugged into a standard 3-prong outlet that is properly installed and grounded. The water cooler is intended to be plugged into a receptacle of the ground fault circuit interrupting type (GFCI) for water cooler installations in North America."

20. Consult a qualiﬁed electrician if the grounding instructions are not completely understood, or if doubt exists as to whether the appliance is properly grounded."

21. If the outlet is a standard 2-prong wall outlet, it is your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet."

22. Do not under any circumstances cut or remove the third (ground) prong from the power cord."

23. Do not use an adapter plug with this appliance."

24. Do not use an extension cord with this appliance. If the power cord is too short, have a qualiﬁed electrician install an outlet near the appliance."

25. Never place your ﬁngers or any sharp metal object inside the water cooler, as doing so may damage the cooler, and also increase the risk of electric shock."

26. Do not immerse the appliance in the water to clean."

27. The appliance should not be exposed to rain. "

28. If the power cord is damaged, it must be replaced by the manufacturer its service agent or similarly qualiﬁed persons in order to avoid a hazard."

PLEASE FOLLOW THE STEPS IN THIS MANUAL IN ORDER !

Please visit mojowater.com/setup

For MOJO SET-UP & TROUBLESHOOTING VIDEOS &

updated installation manuals. Thank you.

3

IMPORTANT

DO NOT TURN ON HOT TANK SWITCH (ON THE BACK OF THE COOLER) UNTIL THE COOLER’S RESERVOIRS ARE FILLED WITH WATER. THEY ARE FULL WHEN WATER COMES OUT OF BOTH THE COLD AND HOT FAUCETS.

GENERAL OVERVIEW

Cold Water Button

Hot Water Selector

Water Outlet

Drain

Hot Water On/

Off Switch

Drip Tray

Lid

Filter

Location

Cold Water Thermostat

Water Inlet

Water

dispense

button

4

Float Kit Information:

The Float Kit sits inside of the cold water reservoir and shuts oﬀ the water when the reservoir is full. The Primary Float (the square one - and “lower” one) shuts oﬀ the water ﬁrst. If that Float were to fail, the water level would keep rising and the Secondary Float would shut oﬀ the water. When this happens, water can not ﬂow again unless the reset button is pressed. Please note: this Secondary Float can be tripped by bumping or moving the cooler. So, if your water stops ﬂowing, you may just need to press reset. !

External Lid

Water Flow

From Filter

Water From Water Filter

5

Cooler Set-Up & Installation: Part 1 - Pre-Installation

1. REMOVE EXTERNAL LID

Remove the lid on the Frost cooler to expose the top of the Float Kit (it is blue and covers the reservoir). There is a small, rounded “cut out” in the back of the lid to help you remove it.

2. LIFT OUT FLOAT KIT

When you remove the External Lid (previous step), you’ll see the blue Float Kit that seals the cold water reservoir (and holds the 2 ﬂoats). You need to remove that lid so that you can check everything inside the reservoir. " Just grab the two handles on the sides and pull straight up (see diagram on previous page).

3. CHECK FLOATS

Look under the Float Kit. You will see 2 air-ﬁlled “ﬂoats” - a main “ﬂoat” (square) that shuts oﬀ the water ﬂow when reservoir is full, and a round backup safety ﬂoat if the ﬁrst ﬂoat were to fail. Occasionally, ﬂoats come loose in transportation. If either ﬂoat is not attached, click it back into place. Make sure that both ﬂoats can freely move up and down.

FLOAT KIT

EXTERNAL LID

PRIMARY FLOAT

BACKUP FLOAT

4. CHECK BAFFLE

a) Inside the stainless steel reservoir, you’ll ﬁnd a 2-piece baﬄe. Sometimes, this can come loose in transportation. Push the baﬄe down to make sure that it is secure. (If it is loose, it can rise up and trip the ﬂoats.) If the baﬄe is dislodged, push it into the center hole in the bottom of reservoir.

5. PRESS RESET BUTTON

a) Push the Float Kit back into the reservoir to seal it. " b) Press red reset button. If the round Backup Float (from Step 3) is tripped, it shuts oﬀ all water to the cooler as a safety precaution. This can also happen in transportation or if cooler gets bumped (after it is installed). " In the future, if water does not dispense, pushing the red button usually ﬁxes the issue.

6. REPLACE LID

Replace the external lid. You’re now ready to proceed with set up.

BAFFLE

RESERVOIR

6

Cooler Set-Up & Installation: Part 2. FILTER SET UP

WRITE DATE

HERE

9. REMOVE DRIP TRAY

Remove the “Drip Tray” by pulling it straight out. There are pegs in the back of the drip tray to keep it in place. It may be a little tight - so just pull it straight out away from the cooler.

8. PREPARE FILTER

Open the included MOJO Water ﬁlter and remove the cap. " Write the date on the front of the ﬁlter so you know when you installed/replaced the ﬁlter. " Your Frost cooler uses M1000 ﬁlters that are always available on MOJO Water's website or on Amazon.

7. FROST LOCATION

Locate the Frost water cooler in a well-ventilated space where temperature is always above freezing. The Frost should be 2 inches from the wall to allow for proper ventilation. The electrical cord plugs into a standard 3prong electrical outlet and is 6feet long. The Frost plugs into a standard 1/4-inch water line (same size as ice makers)

11. INSTALL FILTER

Insert the ﬁlter cartridge in the ﬁlter head. Twist to the right to lock it into place. Make sure that the label is facing towards you.

12. LINE UP GUIDES

a) Make sure that you’ve rotated the ﬁlter all the way in place so that the guides line up. When the guides are not lined up, water will not ﬂow. This makes changing the ﬁlter much easier. " b) Replace the Filter Cover (from Step 10) and then the Drip Tray (from Step 9).

10. REMOVE FILTER COVER

Just grab the ﬁlter cover by the bottom (or by the front) and lift it up. Then, remove it to reveal the ﬁlter compartment.

FILTER HEAD

7

Cooler Set-Up & Installation: Part 3. FINAL SET UP

15. PLUG INTO OUTLET

Plug Frost cooler into standard 3prong electrical outlet. You do not need to wait for the cooler to ﬁll completely from the previous step.

14. TURN WATER ON

Turn the water on by turning the valve so that it is parallel with the waterway. (Water is oﬀ when it is perpendicular.) " You will hear the water start to ﬁll the internal cold water reservoir.

13. PUSH IN WATERWAY

Push the waterway coming from the wall into the Water Inlet (marked Water In). You will feel a slight resistance when you ﬁrst push the waterway into the Water Inlet. Push the waterway past that initial slight resistance (all the way in). The waterway locks/seals automatically. No tools are needed. " Do NOT turn on hot water switch.

18. FLUSH FILTER

a) Place a bucket, trash can, coﬀee pot or even a large cup under the dispensing area. " b) Press the BLUE button on the front. (The top water dispensing button will turn blue.)" c) Press the water dispensing button and ﬁll about a half gallon of water into the bucket. " Wait up to 30 minutes for initial cooling and heating of your water. " Enjoy!

17. TURN ON HOT SWITCH

After water comes out of hot faucet (previous step), remove label and turn on hot tank switch. " TIPS: If you do not want hot water to be dispensed from your cooler, leave this switch oﬀ. Please note that the red switch will light up when the water heater is activated. Once hot water reaches desired temperature, heater turns oﬀ and switch does

not illuminate.

WATER ON

POSITION

HOT SWITCH: DO NOT TURN ON UNTIL YOU

COMPLETE STEP

16. FILL HOT TANK

a) Place a bucket, trash can, or other container under the dispensing area. " b) Press the red button on the front. (Water dispensing button turns red.)" c) Press the water dispensing button on the top & hold it until water comes out of the dispensing area (may take 3+ minutes). Once a steady stream of water comes out, release button and let cooler reﬁll. Water must come out of cooler before moving to Step 17.

212

FILL HOT TANK

FLUSH FILTER

THROUGH COLD

FAUCET

8

BASIC OPERATION/TIPS:!

TO DRAIN COOLER

The dispensing button does not drain the cooler completely. To remove all water from cooler: "

1) Unplug cooler from electrical outlet & let the hot water cool down for an hour+. Then, 2) remove drain plug on the back of the cooler by pulling it straight out and let the water ﬂow into a bucket or trash can. Be careful -

water may still be hot.

cold temp adjustment

Adjust the temperature of the cold water by rotating the thermostat control located on back of the cooler. Use a “ﬂat-head” screwdriver. Clockwise is colder. " TIP: If you turn the thermostat all the way counterclockwise, you’ll turn oﬀ the cold function. The Frost will now dispense Hot (assuming the hot tank switch is on) and room temperature water.

TO REMOVE WATERWAY

When the waterway was pushed into the Water Inlet (marked Water In), it locks into place. If you pull the waterway out without unlocking it, leaks can occur. " To remove the waterway: Push on ring around the Water Inlet while you simultaneously pull the waterway out. Pushing on the ring unlocks the Water Inlet.

LINE UP FILTER GUIDES

When changing ﬁlter, make sure that you’ve rotated the ﬁlter all the way in place so that the guides line up. When the guides are not lined up, water will not ﬂow. " Also, please note the model number when ordering replacements. They’re always available on our website or on amazon.com.

TURNING WATER OFF

To turn the water oﬀ, turn the valve so that it is perpendicular to the waterway.

TURN

CLOCKWISE FOR

WITH A

SCREWDRIVER

COLDER

WATER VALVE

IN OFF

POSITION

HEATING ON/OFF SWITCH

If you do not want hot water to be dispensed from your cooler, turn the hot water switch oﬀ. Please note that the hot on/oﬀ switch will illuminate (red) when the water heater is activated. Once hot water reaches desired temperature, heater turns oﬀ and light inside the switch turns oﬀ.

PUSH IN ON

RING TO UNLOCK

Mojo Frost M1-22 Operation Manual

Specifications and Main Features

Frequently Asked Questions

User Manual