MA-201fet
Solid State Condenser Microphone
Please visit www.mojaveaudio.com for more information including:
•
Recording Tips
•
FAQ’s
•
Warranty Registration
•
Customer Service
CONTENTS
INTRODUCTION 2
UNPACKING AND INSPECTION 2
SAFETY INSTRUCTIONS 3
OPERATION 3
CARE OF YOUR MICROPHONE 3
TECHNICAL SPECIFICATIONS 4
POLAR RESPONSE 5
FREQUENCY RESPONSE 5
WARRANTY 6
INTRODUCTION
Congratulations on your purchase of a Mojave Audio MA-201fet Solid State Capacitor
Microphone! Your MA-201fet was carefully designed and constructed using only the finest
materials. The MA-201fet microphone is capable of delivering superb performance and, with
minimal care, will do so for many years. Your MA-201fet was thoroughly tested and given a
factory burn-in prior to shipment.
The MA-201fet is guaranteed to perform as specified and is suitable for recording even the most
demanding music, provided that the microphone is used sensibly.
For optimum performance from your new microphone, please read this manual thoroughly and
become familiar with the proper use of the MA-201fet.
UNPACKING AND INSPECTION
Carefully unpack your MA-201fet microphone and verify that all of the components included
with the microphone are accounted for. Do not discard any packing materials! If anything is
missing or damaged, contact your dealer or Mojave Audio immediately.
Items included with the MA-201fet are:
1. MA-201fet microphone inside an aluminum style carrying case
2. MA-201fet shock mount and European adapter (fitted to shock mount)
Verify that the serial number of your MA-201fet!matches correctly with the one on your receipt.
The MA-201fet serial number can be found ! inside the microphone housing. To access, simply
unscrew the bottom ring and slide the body off. When corresponding with Mojave Audio about
your microphone or when service is required, we will need to know the serial number, so keep it
handy.
SAFETY INSTRUCTIONS
There are no user serviceable components inside the MA-201fet microphone Always refer
service to qualified technician equipped to service this equipment. Never expose the MA-201fet
microphone or cable to water or any environment that may create an unsafe electrical hazard. In
the event of a malfunction, disconnect the MA-201fet immediately and determine the nature of
the malfunction before attempting to use it again.
To avoid tripping over the microphone cable, make certain that the cable is not in the way of foot
traffic, or suspended in an unsafe manner. Make sure that the microphone stand is secure and not
likely to fall.
If you have any questions or concerns about operation of your MA-201fet please contact the
factory.
OPERATION
When plugging the microphone in, the three-pin XLR connectors between the microphone and
the mic preamp should be inserted gently into their corresponding sockets. Rough handling,
misaligned orientation, or trying to force the connections together too quickly could result in
bent pins.
The MA-201fet requires standard 48v phantom to operate.
CARE OF YOUR MICROPHONE
Your microphone is a delicate precision instrument and it should be treated as such.
Here are some commonsense rules to keep your microphone healthy.
1. Be careful in your setup so that the microphone never falls to the floor. Never suspend the
microphone by its cable and be sure to position the cable so that it cannot be tripped over.
Drops to the floor have been the demise of many a microphone.
2. Never hot-plug the microphone (i.e. plug the microphone into a mic pre with 48v phantom
power turned on), as the resulting voltage surges can damage the mic’s or following
preamplifier's electronics. Always connect mic first, then turn on 48v supply.
3. Keep the microphone in a safe place, such as its carrying case or a microphone locker, when
not in use.
4. When plugging in the three-pin XLR cable between the microphone and mic preamp, orient
the plug correctly and plug the connectors in gently. Rough handling or hurry-up plug-ins can
result in bent pins.
5. Do not expose the microphone to dusty, smoky or humid environments.
6. Do not attempt repairs unless you are a qualified technician. There are no user serviceable
parts in the MA-201fet.
7. Use a soft, lint free cloth to remove fingerprints and other blemishes on the microphone body.
Never use chemicals, solvents or detergents.
TECHNICAL SPECIFICATIONS
TRANSDUCER TYPE: Externally polarized pressure gradient capacitor
DIAPHRAGM: 1-inch diameter, gold sputtered, single-sided
DIAPHRAGM THINKNESS: 3-micron
POLAR PATTERN: Cardioid
FREQUENCY RESPONSE: 20 Hz-20kHz, + 3dB
SENSITIVITY: -39 dB re. 1V/pa
MAXIMUM SPL: 125 dB
DISTORTION: <1% @120dB SPL, <3% @ 134dB SPL
SELF NOISE: 14dB nominal, not to exceed 16dB (A weighted)
IMPEDANCE: 550 ohms, transformer balanced (Jensen)
POWERING: 48VDC phantom power; current .68mA.
DIMENSIONS AND WEIGHT: Carrying case with microphone, shock mount:
10” x 9” x 4.5”, 4 lbs.
Microphone: 7 5/8” x 2”, 1 lb.
POLAR RESPONSE
Type: Cardioid
FREQUENCY RESPONSE
20Hz – 20kHz, ±2.5dB
WARRANTY
Your Mojave Audio product is warranted to the original owner for a period of two years. Mojave
Audio guarantees this product to be free from electrical and mechanical defects and will repair or
replace defective components, or replace the microphone at Mojave Audio's option. Should
service be required for your Mojave Audio product, please contact the manufacturer. Excellent
service will also be provided for products beyond the warranty period at a modest cost for parts
and labor.
Please visit mojaveaudio.com for the latest updates and technical information.
MODEL NUMBER_________________
SERIAL NUMBER__________________
DATE OF PURCHASE_______________
PURCHASED FROM________________________
2711 Empire Street • Burbank, CA 91504 • tel. 818.847.0222 • www.mojaveaudio.com
Loading...