Moffat, Inc. AL8 General Manual

AL8 Passthrough Warewasher

The AL8 accommodates regular 500mm dishracks plus all
crates, bins, dixies etc. up to 700 wide by 540 deep by 650mm
high - includingmany80 litre mixer bowls.

High temperature sanitising rinse uses about 3 litres of water per
cycle, regardless of cycle time, for highly efficient operation ­minimising water,waste, power and chemicalcosts.

Operator may select 2, 4 or 6 minute cycles for rapid washing of a
wide range of soil levels. Other cycle times available on request e.g.
1,2,3 minutes if your soillevels are light.

The massive 1.5 kW wash pump recirculates 800 litres of water per
minute through double upper and lower wash arms for exceptional
wash performance. Double filtration in the deep L shape wash tank
isolates solid soil on easilyremovable scrap trays.

Powerful rinse booster elements ensure rapid recovery between
cycles for high capacity.

AL8

AL8

PASSTHROUGH WAREWASHER

Light, well balanced door with wrap around handle. Operator
preselects required cycle which thenauto-starts on door closure.

FASTCLEAN features include : rounded L shape wash tank,
uncluttered internal design, easy-tilt rack slide, double filtration,
scrap trays, stainless steel wash and rinse arms with removable
end plugs, anti-drip door to channel water away from opening, and
220mm legs for excellent accessbeneath machine.

Electrical requirement is 25 amps 3 phase, with neutral and earth.
750mm benches are recommended. Corner installation is possible
but generally not recommended.

Supplied with two dishracks,one cuprackand one cutlery basket.

20

Installation drawing and detail overleaf.

540

700

Wash Chamber

Over 25 years Washtech has earned the position of
Australasia's leadingwash equipmentmanufacturer
by providing robust, reliable machines designed for
ease of service and years of effective, efficient
operation.

ISO 9001 certified and audited since 1993 - our
equipment complies with all local hygiene, electrical
and plumbingregulations includingWATERMARK.

Washtech products are supported nationwide by the
MOFFAT Service Network to ensure long term
access to parts and after sales support and service
including preventativemaintenance programmes.

18

SERVICE & SUPPORT

In linewith policy to continually develop and improve
it's products Moffat reserves the right to change
specifications anddesign withoutnotice.

WaterMark

ATS5200.101

Cert 08603

SAI GLOBAL

24

12

7

650

TM

6

2,4,6

3.5

650

25A

3

500

750

280

www.moffat.com.au

24 HOUR SERVICE

1800 622 216

REPLACEMENT PARTS

1800 337 963

Australia Moffat Pty Limited

Victoria/Tasmania
740 Springvale Road
Mulgrave, Victoria 3170
Telephone [phone]
Facsimile 03 9518 3833
Email [e-mail]
www.moffat.com.au

New South Wales
Telephone [phone]
Email [e-mail]

South Australia
Telephone [phone]
Email [e-mail]

Queensland
Telephone [phone]
Email [e-mail]

Western Australia
Telephone

08 9202 6820

Email

[e-mail]

Effective November 2007

AL8 Passthrough Warewasher

AL8

Installer must be suitably qualified and ensure
compliance with all local codes and standards
including AS/NZS 3500.1. Failure to comply even
partially with installation instructions may void the
warranty. Install machine on sound waterproof self­draining floor and use adjustable feet to level
machine. Allow room for detergent to one side of
machine or in adjacent cupboard. 20 litre container
requires about 450H x 250W x 350D, but smaller
containers are available from many suppliers.

Water Supply

Hot water temperature 65°C ± 5°C
Connection 20 mm (3/4" BSP Male)
Pressure 200-350 kPa = 30-50 psi
Flow rate minimum 20 litres per minute
Consumption per cycle 3.5 litres approximately
Backflow prevention Dual Check Valve supplied

Pressure limiter may be required. Don't use small
diameter plastic supply lines. FLUSH supply line
before connection. Connect supplied DCV to water
supply. Poor quality supply or excessive water
hardness may affect performance or damage
machine - filtration and/or softening is
recommended. Optional rinse booster pump
available for very low pressure supply.

Waste

40mm gravity drain - refer to point B in the
installation diagram - run waste directly behind the
machine or through open side panelsor base.

Power

Machine requires 3 Phase, Neutral and Earth,
400/415V, 25A/ph, 50Hz, permanently wired via
wall switch mounted adjacent to machine. Wash
pump rotation must be checked after installation to
ensure correct direction (excessive noise and
damage with incorrect direction).

Benchwork

Refer to relevant drawings - alldimensions in mm.
Recommended bench depth is 750, height 900.
Corner installation is not recommended for this
model. We recommend sink smaller than rack, with
guide to prevent rack falling into sink. Align sink with
dishrack as shown.