Page 1
Technical data sheet for
GAS RANGE ELECTRIC
CONVECTION OVEN 900mm
RN8610GEC, RN8613GEC, RN8616GEC, RN8619GEC
Heavy-duty construction
28 MJ/hr open burners
Flame failure standard
Pilot burners optional
300mm, 600mm, and 900mm griddle plate options
Optional simmer plates
GN 2/1 6.6kW electric convection oven
Drop down door
Stainless steel exterior
Easy clean
Easy service
RN8610GEC
Fully modular
Overall Construction
• Galvanized steel chassis
• Welded hob with 1.5mm 304 stainless steel bull nose
• Splashback and hob sides 1.2mm 304 stainless steel
• Front panels and oven sides 0.9mm 304 stainless steel
• 150mm legs in 63mm dia. heavy-duty 1.2mm 304 stainless steel
with adjustable feet
Cooktop
• Cast iron 28MJ/hr open burners with forged brass cap
• Vitreous enamelled cast iron potstands
• Vitreous enamelled open burner spill covers
• Cast iron simmer plates (optional extra)
• 12mm thick mild steel griddle plates
• 2.5mm 304 stainless steel griddle splash guards
• Vitreous enamelled spill trays
• Aluminised steel internal construction
Griddle sections are standard on RH side. Available on LH side or
centre to order or by conversion.
Oven
• Fully welded and vitreous enamelled oven liner
• GN 2/1 capacity with 4 position racking
• Heavy-duty easy remove heavy wire chrome rack supports
• Cast iron even heat oven sole plate
• 6.5kW heating elements
• 100W heavy-duty motor
• 200mm diameter heavy-duty circulation fan
• Welded frame drop down door with heav y-duty spring
hinge system
• 0.9mm 304 stainless steel door outer
• 1.0mm press formed vitreous enamelled door inner
• High density fibreglass insulated
• Stay cool stainless steel door handle with cast metal handle mounts
• Supplied with two chrome wire oven racks
Controls
• Large easy use control knob - heat resistant reinforced
• Easy view control settings on knob
Cooktop
• Variable high to low controls to open burners
• Open burners flame failure standard with pilot burners optional
• Variable high to low controls to griddles
• Griddles standard with pilot, flame failure and piezo ignition
Oven
• 50-320˚C thermostatic control
• Indicator lights for power and heating
Cleaning and Servicing
• All models with easy clean stainless steel external finish
• Lift off burners heads and vitreous enamelled burner spill covers
• Vitreous enamelled spill trays under open burner and
griddle sections
• Removable oven racking and sole plate
• Easy clean vitreous enamel oven and door inner
• Door hinge spring adjustable on unit (door outer removed)
• Door disengages for lift off removal and increased service access
• All parts front accessible from installed position
• Access to all parts from front of unit
Page 2
Technical data sheet for
GAS RANGE ELECTRIC
CONVECTION OVEN 900mm
Specifications
Burners
Open Burners 28M J/hr dual flame ring with
simmer rate
Griddle Burners 20M J/hr per 300mm section
Oven Elements
4.5kW bottom heat element
2.0kW top heat element
Gas power
RN8610GEC 168 MJ/hr, 46.6kW
RN8613GEC 132 MJ/hr, 36.6kW
RN8616GEC 96 MJ/hr, 26.6kW
RN8619GEC 60 MJ/hr, 16.6kW
Oven Fan Motor
100W
Electrical requirements
6.6kW
1 phase connec tion:
230-240Vac, 50/60hz, 1P+N+E, 27.7A
3 phase connec tion:
400-415Vac, 50/60hz, 3P+N+E
L1 9.4A
L2 9.4A
L3 9.0A
Griddle Plate
300mm Griddle cooking surface
292mm x 475mm, 1387cm2
600mm Griddle cooking surface
592mm x 475mm, 2812cm2
900mm Griddle cooking surface
892mm x 475mm, 4237cm2
Oven Dimensions
Width 665mm
Depth 590mm
Height 385mm
Rack size 660mm x 540mm
Rack positions 4
Gas connection
3
/4 (BSP) male
R
130mm from RH side, 32mm from rear, and
655mm from floor
All units supplied with Natural and LP gas
regulator
Electrical connection
23mm from RH side, 484mm from rear,
and 150mm from floor
Dimensions
Width 900mm
Depth 805mm
Height 915mm
Incl. splashback 1130mm
Pack ing data
1.02m3
Width 940mm
Depth 865mm
Height 1255mm
Gas types
Available in Natural gas and LP gas
Please specif y when ordering
Units supplied complete with gas type
conversion kits
Other gas types on request
Options at extra cost
Simmer plates (replaces Potstand)
Ribbed griddle plates
Joining caps
Castors
Plinth mounting
RN8610GEC, RN8613GEC, RN8616GEC, RN8619GEC
RN8610GEC
RN8613GEC
RN8616GEC RN8619GEC
Australia
www.moffat.com.au
New Zealand
www.moffat.co.nz
Australia
Moffat Pty Limited
Victoria/Tasmania
740 Springvale Road
Mulgrave, Victoria 3170
Telephone 03-9518 3888
Facsimile 03-9518 3833
vsales@moffat.com.au
New South Wales
Telephone 02-8833 4111
nswsales@moffat.com.au
South Australia
Telephone 03-9518 3888
vsales@moffat.com.au
Queensland
Telephone 07-3630 8600
qldsales@moffat.com.au
Western Australia
Telephone 08-9562 0263
jberent@moffat.com.au
New Zealand
Moffat Limited
Christchurch
Telephone 03-389 1007
sales@moffat.co.nz
Auckland
Telephone 09-574 3150
sales@moffat.co.nz
ISO9001
Quality
Management
Standard
Designed and manufactured by
ISO9001
All Waldorf products are designed and
manufactured by Moffat using the
internationally recognised ISO9001 quality
management system, covering design,
manufacture and final inspection, ensuring
consistent high quality at all times.
In line with policy to continually develop and
improve its products, Moffat Limited reserves
the right to change specifications and design
without notice.
Printed in New Zealand
© Copyright Mo ffat Limited
Moffat/4639/BH/1M/8.05
Loading...