Moffat E89MS Installation Manual

INSTALLATION / OPERATION

MANUAL

E89M & E89MS
PROVER / HOLDING CABINET

F25612-5

MANUFACTURED BY

Moffat Limited
PO Box 10001
Christchurch
New Zealand
Ph: [phone]
Fax: [phone]

WORLD-WIDE BRANCHES

UNITED KINGDOM

Blue Seal
Units 6-7, Mount Street Business Park
Mount Street, Nechells
Birmingham B7 5QU
Ph: [phone]
Fax: [phone]

UNITED STATES

Moffat Inc
3765 Champion Blvd
Winston-Salem
North Carolina 27115
Ph: [phone]
Fax: [phone]

CANADA

Serve Canada
22 Ashwarren Road
Downview
Ontario M3J1Z5

Toll Free:800 263 1455
Ph: [phone]
Fax: [phone]

[e-mail]
www.servecanada.com
www.moffat.com

NEW ZEALAND

Christchurch

Moffat Limited Moffat Limited
PO Box 10-001 4 Waipuna Road
16 Osborne Street Mt Wellington
Christchurch Auckland
Ph: [phone] Ph: [phone]
Fax: [phone] Fax: [phone]

AUSTRALIA

Victoria

Moffat Pty Limited Moffat Pty Limited
740 Springvale Road 3/142 James Ruse Drive, Rose Hill
Mulgrave, Melbourne PO Box 913, Smithfield
Victoria 3171 Sydney, N.S.W. 2142
Ph: [phone] Ph: [phone]
Fax: [phone] Fax: [phone]

Western Australia

Moffat Pty Limited Moffat Pty Limited
67 Howe Street 30 Prosperity Place
Osbourne Park Geebung, Brisbane
WA 6017 Queensland 4034
Ph: [phone] Ph: [phone]
Fax: [phone] Fax [phone]

Auckland

New South Wales

Queensland

The reproduction or copying of any part of this manual by any means whatsoever is strictly forbidden unless authorized previously in
writing by the manufacturer.

In line with policy to continually develop and improve its products, Moffat Ltd. reserves the right to change the specifications and
design without prior notice.

© Copyright Moffat Ltd. November 2006.

Contents

Introduction ........................................................................................................ 2

Installation..........................................................................................................3

Before Connection
Location
Electrical Connection
Water Connection (Auto Fill Models Only)
Rack Width
Stacking with Convection Oven

Specifications.....................................................................................................5

Operation............................................................................................................9

Description of Controls
Condensation Channel
Operating in PROOF Mode
Bake-Off
Problem Solving
Hints
Operating in HOLD Mode

Cleaning and Maintenance..............................................................................13

Trouble Shooting .............................................................................................14

Spare Parts.......................................................................................................15

Circuit Schematics...........................................................................................16

E89 Prover / Holding Cabinet (Manual Fill)
E89A Prover / Holding Cabinet (Auto Fill)

Date Purchased................................................................. Serial No ..........................................................

Dealer ............................................................................................................................................................

Service Agent ................................................................................................................................................

1

Introduction

We are confident that you will be delighted with your E89M/MS PROVER / HOLDING CABINET, and it will
become a most valued appliance in your commercial kitchen.

A new oven can seem very complex and confusing at first glance. To ensure you receive the utmost
benefit from your new Prover, there are two important things you can do.

Firstly

Please read the instruction book carefully and follow the directions given. The time taken will be well
spent.

Secondly

If you are unsure of any aspect of the installation, instructions or performance of your prover, contact your
E89M/MS dealer promptly. In many cases a phone call could answer your question.

2

Installation

Installation Requirements

It is most important that this prover / holding cabinet is installed correctly and that
operation is correct before use.

Installation shall comply with local electrical, health and safety requirements.

Before Connection to Power Supply

• Remove all packing.

• Check equipment and parts for damage. Report any damage immediately to the carrier and
distributor.

• Remove protective plastic coating from the side panels.

• Check that the available power supply is correct to that shown on the rating plate located on the
right-hand side panel.

E89MS 110-120 Volts A.C, 60 Hz, 1P+N+E, 1.50 kW, 12.5 A @ 120V
E89M/MS 208-220 Volts A.C, 50/60 Hz, 1P+N+E, 1.45 kW, 6.5 A @ 220V
E89M/MS 220-240 Volts A.C, 50/60 Hz, 1P+N+E, 1.70 kW, 7.1 A @ 240V

Location

• To ensure correct ventilation for the and controls the following minimum installation
clearances are to be adhered to:

Rear 0 mm / 0 ”
Left-hand side 0 mm / 0 ”
Right-hand side 25 mm / 1 ”

Electrical Connection

• E89M/MS provers are supplied fitted with cords. Ensure unit is fitted with correct cord and plug.

• To access the electrical connection terminal block, grounding lug and strain relief, remove the
right hand side panel.

WARNING - THIS APPLIANCE MUST BE EARTHED / GROUNDED

Water Connection (Auto Fill Models Only)

• A cold water supply should be fitted to the water inlet which is located near the rear of the right
hand side of the unit.

• A connection elbow and sealing washer is supplied with this unit for direct connection of a ½” ID
hose, and is recommended for easy installation and service.

• Connect water supply - Max inlet pressure 550kPa / 80psi.

• Turn on water supply to check for leaks.

Rack Width

• The E89 prover has been designed to accept either 460mm (18”) or 405mm (16”) wide trays or 1/1

• The prover comes factory set for 460mm (18”) trays, a rack spacer kit (Part no. 025685) is

1

GN,

/2 /1 GN trays.

required to change to 405mm (16”) trays or Gastronorm pans.

3

Installation

Stacking with Convection Oven

• The E89M/MS prover is supplied standard for stand alone use.

• Optionally, the E89M/MS prover can be double stacked, or combined underneath a TURBOFAN
E32M/MS convection oven as a complete unit. For this a stacking kit is required.

• For installation of the stacking kit, refer to the instructions provided with the kit.

4

Specifications

E89M Prover

710

515

Front

51.5

68

WATER ENTRY

ELECTRICAL ENTRY

355

200

810

610117.5

Side

900

66.5

710

Plan

Electrical Connection

Cold Water Connection
(Auto Fill Models Only)

208-220 Volts A.C, 50/60 Hz, 1P+N+E, 1.45 kW, 6.5 A @ 220V
220-240 Volts A.C, 50/60 Hz, 1P+N+E, 1.70 kW, 7.1 A @ 240V

1

/2“ ID hose (550kPa / 80psi maximum pressure)

5