Page 1
Quick Connect Fittings
Installation and Removal
Tool needed: Pliers (optional)
Identify your connection style and move to the appropriate step.
Below are the different hoses and quick connect fittings addressed by this document. The two
hose styles are found on both Hydrolockl and Duralock connection systems. These are only
included for reference.
Hose Ends
White Tip Brass Tip
A. Hydrolock Fittings
Hose Under Faucet Double Female Small Double
Female
Go to step 1 to remove or step 4 to install
B. Duralock Fitting
Go to step 10 to
remove or step
12 to install
Disconnecting a Hydrolock Fitting
1.
2. Find the two white plastic tabs at the end of the Quick Connect fitting. Squeeze these tabs
together with your fingers or pliers. As you squeeze these tabs they will become pushed into
the black plastic housing. This will cause the white button on the opposite side of to pop out a
little.
3. The Quick Connect fitting is now unlocked. Slide the fitting off.
Page 2
Connecting a Hydrolock Fitting
4. Inspect the Quick Connect fitting to insure the white button is pulled out and slightly raised from
the black plastic.
5. Slide the Quick Connect onto the shaft until the Quick Connect is fully seated and can not be
pushed any further. Make certain the hose is pushed into the
Quick Connect straight and not at an angle.
6. Push the white button until you hear a click.
7. The white button should now be depressed and there should be
two white tabs protruding from the side opposite of the button.
8. Turn water supplies on and, with water running through the Hydrolock fitting, inspect the area
for leaks. If there is a leak from the Hydrolock fitting, please refer to the “Special Note” section
below.
9. If there is not a leak from the Hydrolock fitting, the connection is complete and the item is
ready to use. This item can be disconnected and reconnected as needed. For disconnecting
this item, please refer the “Disconnecting a Hydrolock FItting” section in this document.
You are all done!
Special Note
Resolving a Leak from a Hydrolock Fitting
Use these steps if a leak appears right after installation
1. Remove the Hydrolock fitting by using the “Disconnecting a Hydrolock” section in this
document.
2. Inspect the end of the shaft. Insure that this O-ring is in the groove.
3. Reconnect the Quick Connect using the “Connecting a Quick Connect” section in this
document. Make certain the hose is pushed into the Quick Connect straight and not
at an angle. This will allow the fitting to seal properly.
1
Page 3
Disconnecting a Duralock Fitting
10.
11. Push the hose gently into the Duralock connector and then push the black button. While holding this
black button pull the hose end out of the Duralock fitting.
Connecting a Duralock Fitting
12. Hold the Duralock fitting without pushing the button. Slide the hose end into the this fitting until
you hear the fitting “click”. This indicates the lock has engaged. If you are unable to get this fitting
to lock, see the special note at the end of this section
13. If there is not a leak from the Duralock fitting, the connection is complete and the item is ready to
use. This item can be disconnected and reconnected as needed. For disconnecting this item,
please refer the “Disconnecting a Duralock Fitting” section in this document.
You are all done!
Special Note
If the Duralock Fitting is Unable to be Locked
Use these steps if you are unable to get the hose in all of the
way or if the fitting will not lock onto the hose end.
4. If needed, remove the fitting by using the “Disconnecting a Duralock Fitting”
section in this document.
5. Inspect the end of the fitting to insure there is not a blocked passageway. A
clear passageway will either be hollow or appear like the photo to the right.
Remove any item obstructing the passageway and then reinstall using the
“Connecting a Duralock Fitting” section in this document.
2
Loading...