Moen 9200 User Manual

INS271

4 HOLE BIDET - VALVE ONLY

MODEL 9200 SERIES HANDLES AND OTHER TRIM PARTS SOLD SEPARATELY

BIDET DE 4 ORIFICIOS - SOLO VALVULA

MODELO 9200 MARLEALES Y OTRAS PARTES VENDIDAS APARTES.

BIDET À 4 OUVERTURES - ROBINET SEULEMENT

MODÈLE 9200 Série LES POIGNÉES ET LES AUTRES PIÈCES DE GARNITURE SONT VENDUS SÉPARÉMENT

HELPFUL TOOLS HERRAMIENTAS UTILES OUTILS UTILES

ENGLISH ESPAÑOL FRANÇAIS

KEEP INSTRUCTIONS FOR FUTURE REFERENCE

Thank you for purchasing a quality MOEN faucet.With simple care and maintenance, it will provide you with many years of reliable performance. Please read all instr uctions before installation.

Questions During Installation?

1-800-BUY-MOEN

(1-800-289-6636)

Toronto 905-829-3400

Rest of Canada 1-800-465-6130

TIPS FOR REMOVAL OF OLD FAUCET:

CAUTION: Always turn water OFF before

removing existing faucet or disassemb ling the valve. Open valve handle to relieve water pressure and ensure that complete water shut-off has been accomplished.

GUARDE ESTAS INSTRUCCIONES PARA REFERENCIA FUTURA

Gracias por haber comprado una mezcladora de alta calidad de MOEN. Con un cuidado y mantenimiento sencillos, le brindará muchos años de servicio fiable. Por favor lea todas las instrucciones antes de instalar.

¿Preguntas durante la instalación?

1-800-BUY-MOEN

(1-800-289-6636)

Toronto 905-829-3400

Resto del Canadá 1-800-465-6130

SUGERENCIAS PARA QUITAR LA VIEJA MEZCLADORA:

ADVERTENCIA: Siempre cierre el agua

antes de remover la mezcladora existente o desarmar la válvula. Abra las manijas de la mezcladora para aflojar la presión del agua y para asegurar que el cierre completo del agua ha sido logrado.

CONSERVER CES DIRECTIVES POUR RÉFÉRENCE ULTÉRIEURE

Merci d’avoir acheté un robinet de qualité MOEN. Avec un peu de soin et d’entretien, ce robinet vous donnera plusieurs années de rendement fiable. Lire attentivement toutes les directives avant de débuter l’installation.

Des questions lors de

l’installation?

Toronto : (905) 829-3400

Ailleurs au Canada : 1 800 465-6130

SUGGESTIONS POUR ENLEVER L’ANCIEN ROBINET :

A TTENTION : T oujours couper l’alimentation

en eau avant d’enlever ou de démonter le robinet. Ouvrir la poignée du robinet pour libérer la pression d’eau et pour s’assurer que l’alimentation en eau a bien été coupée.

For safety and ease of faucet replacement, Moen recommends the use of these helpful tools.

Para la seguridad y facilidad de repuesto de la mezcladora, Moen recomienda las siguientes herramientas.

Par mesure de sécurité et pour faciliter l’installation, Moen suggère l’utilisation des outils suivants.

Printed in U.S.A.

Complies with: ASME A112.18.1M, CSA B125, & NSF 61/9 Cumple con: ASME A112.18.1M, CSA B125, & NSF 61/9 Respecte ASME A112.18.1M, CSA B125 et NSF 61/9

SAFETY GLASSES

GAFAS DE SEGURIDAD

LUNETTES DE SÉCURITÉ

FLASHLIGHT

LINTERNA

LAMPE DE POCHE

(2)

ADJUSTABLE WRENCH

LLAVE AJUSTABLE

CLÉ À MOLETTE

FLATBLADED SCREWDRIVER

DESTORNILLADOR DE PALA

TOURNEVIS À TÊTE PLATE

PHILLIPS SCREWDRIVER

DESTORNILLADOR DE ESTRELLA

TOURNEVIS À TÊTE ÉTOILÉE

CHANNEL LOCKS

PINZAS DE EXTENSION

PINCES À RAINURE

7/64" HEX WRENCH LLAVE HEXAGONAL

CLÉ HEXAGONALE

BASIN WRENCH

LLAVE DE FREGADERO

CLÉ DE LAVABO

PLIERS PINZAS PINCES

! !

INSTALLATION INSTRUCTIONS

IMPORTANT:

CENTER WASHER UNDER VALVE BEFORE TIGHTENING NUT

THICK METAL WASHER

CARTRIDGE NUT

ESCUTCHEON NUT

DIVERTER V ALVE

FIGURE 1A

LARGE HOLE

(Most Applications)

SMALL RUBBER SEAL

(RIB SIDE DOWN)

LARGE RUBBER

CONE SEAL

THIN METAL WASHER

NUT

BIDET DECK

Supply Valve

Lower Mounting Nut

Retaining Clip

Top Mounting Washer

INSTALLATION OF SUPPLY VALVE:

Before installing supply valves mak e sure that the cartridge nuts are in place.The cartridge and cartridge nuts were properly installed and tested before leaving the factory. Although it is unlikely, it is nevertheless possible that through the handling of the valve by any number of persons, the cartridge nuts may not be properly installed.This should be carefully chec ked at time of installation.If the cartridge nuts are not properly installed, water pressure could force the cartridge out of the valve. Personal injury or water damage to the premises could result.

1. Thread lower mounting nut down the supply valve body. Place the flat support washer on top of the mounting nut.

2. From under the bidet, insert valve housing up through holes. NOTE:V alv e marked "COLD SIDE" should be on the right side as you use the controls.

Apply plumber’s putty to bottom of top mounting washers.The bottom surface of the top mounting washer has a groove to accept the plumber's putty. Center top washers over holes in deck. Slide valve body from under the deck up through sink/deck holes and top washers. Insert retaining clip into the groove on valve body.Release body down until clip rests on the top of the washer.(See Figure 2)

3. Hand tighten the mounting nuts from underneath. Do not tighten completely until after the installation of the supply lines.

INST ALLA TION OF DIVERTER VALVE

1. For bidet with large center hole (most applications), use thick metal washer and small rubber seal above deck and large rubber cone seal below

deck (See Figure 1A). For bidet with small center hole, use thick metal washer and flat rubber seal above deck and small rubber seal below deck (See Figure 1B).

2. Install thin metal washer and mounting nut from below deck and tighten securely with basin wrench (trim upper rubber seal flush with outside edge of bidet valve).

3. Install and lightly tighten escutcheon nut. Install and firmly tighten cartridge nut.

THICK METAL WASHER

FLAT RUBBER SEAL

SMALL RUBBER SEAL

(RIB SIDE UP)

THIN METAL WASHER

NUT

BIDET DECK

FIGURE 1B

SMALL HOLE

Retaining Clip

Top Mounting Washer

INS271

Faucets made of leaded brass alloys may contribute small amounts of lead to water that is allowed to stand in contact with the brass. The amount of lead contributed by any faucet is highest when the faucet is new. The following steps may reduce potential exposure to lead from faucets and other parts of the plumbing system:

• Always run the water for a few seconds prior to use for drinking or cooking

• Use only cold water for drinking or cooking

• If you wish to flush the entire plumbing system of water that has been standing in the pipes or other fittings, run the cold water until the temperature of the water drops, indicating water coming from the outside main

• If you are concerned about lead in your water, have your water tested by a certified laboratory in your area

Moen products have been manufactured under the highest standards of quality and workmanship. Moen warrants to the original consumer purchaser for as long as the original consumer purchaser owns their home (the “ W arranty Period” for homeowners), that this faucet will be leak and drip-free during normal use and all parts and finishes of this faucet will be free from defects in material and manufacturing workmanship. Al l o t he r purchasers (including purchasers for industrial, commercial and business use) are warranted for a period of 5 years from the original date of purchase (the “W arranty Period” for non-homeowners).

If this fa ucet sh ould ever d evelop a leak or dr ip duri ng the Warranty Period, Moen will FREE OF CHARGE provide the parts necessary to put the faucet back in good working condition and will replace FREE OF CHARGE, any part or finish that proves defective in material and manufacturing workmanship, under normal installation, use and service. Replacement parts may be obtained by calling 1-800-289-6636 (Canada 1-800-465-6130), or by writing to the address shown. Proof of purchase (original sales receipt) from the original consumer purchaser must accompany all warranty claims. Defects or damage caused by the use of other than genuine Moen parts are not covered by this warranty. This w a r rant y i s applicable only to faucets purchased after December 1995 and shall be ef fective from the date of purchase as shown on purchaser ’ s r ec ei pt .

This warranty is extensive in that it covers replacement of all defective parts and finishes. However , damage due to installation error, product abuse, product misuse, or use of cleaners containing abrasives, alcohol or other organic solvents, whether performed by a contractor , service company , or y ou r se l f , a r e excluded from this warranty . Moen will not be responsible for labor charges and/or damage incurred in instal lati on, repair or replacement, nor for any indirect, incidental or consequential damages, losses, injury or costs of any n ature re lating to thi s faucet . Except as provided b y law, this warranty is in lieu of and excludes all other warranties, conditions and guarantees, whether expressed or implied, statutory or otherwise, including without restriction those of merchantability or of fitness for use.

Some states, provinces and nations do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights and you may also have other rights which vary from state to state, province to province, nation to nation. Moen will advise you of the procedure to follow in making warranty claims. Simply write to Moen Incorporated using the address below. Explain the defect and include proof of purchase and your name, address, area code and telephone number.

WARRANTY CONSUMER INFORMATION

INSTALLATION INSTRUCTIONS

HELPLINE: 1 (800) BUY-MOEN

[289-6636]

In the U.S.call our toll free Helpline number, for answers to any product installation, or warranty questions.

In Canada:

Toronto: 905-829-3400;

Rest of Canada: 1-800-465-6130

In Mexico:

(84) 88-08-26, 88-08-27,

o 91-800-84-345

CONNECTING SUPPLY VALVES TO DIVERTER VALVE AND WATER SUPPLIES:

1. Slide "TEE" onto inlet tube and tighten compression nut. NOTE: Check to

insure ferrule and nut are in place before installing tee onto inlet tube. Thread one end of each supply hose onto a supply valve, the other end is threaded to the "TEE" connection inlet. Supply hoses can be crossed or looped for ease of assembly. NOTE: Remove "COLD SIDE" tape before making connection.

2. Connect supply tubes (not supplied) to inlet ports. Finish tightening supply valve mounting hardware.

Hot Side

Cold Side

Supply Tube

"Tee" Connection

Supply Hose

Supply Stop

(not supplied)

Inlet Tube

(not supplied)

DISCHARGE TUBE

SPRAY NOZZLE

RUBBER WASHER RUBBER WASHER

MET AL W ASHER MOUNTING NUT

3/8" x 3/8" x 22" SUPPL Y TUBE

Drain hole

Pop-up drain plug

Drain body

1-1/4" (32mm) Tailpipe Slip joint nut (not included)

Slip joint washer (not included) Floor drain (not included)

Seat

Bottom gasket

Included in bidet trim kit

TO INSTALL WASTE ASSEMBLY:

1. Thoroughly clean around drain opening on bidet drain hole. Apply a

1/4" bead of plumber's putty (not furnished) around the drain opening.

2. Apply pipe joint compound or Teflon tape (not furnished) to top threaded end of drain body. Slip drain body up through the drain opening and screw seat on the drain body.

3. Position the drain body with pivot rod opening extending rearward and tighten mounting nut until the drain body is snug. Wipe excess plumber's putty from seat area. Apply pipe joint compound or Teflon tape to top threaded end of tailpipe and screw into drain body. Tighten firmly by hand.

4. Position the drain plug in either of the following ways:

A. VANDALPROOF - This design is to prevent unauthorized removal

of the drain plug. Unscrew the pivot nut and remove the pivot rod. Inside the drain body, position the pivot rod through the drain plug hole as shown in the illustration. Screw the pivot nut back on the drain body. DO NOT OVERTIGHTEN.

B. EASY REMOVAL - This design is for quick removal of drain plug for

cleaning. Just drop in the drain plug as shown in the illustration.

Pivot RodPivot Rod

VANDALPROOF EASY REMOVAL

A B

INSTALLATION OF SPRAY ASSEMBLY

1. Install r ubber washer over threaded nipple of spray nozzle assembly and

place down through smaller hole in bidet bowl. From below install metal washer, metal washer and mounting nut and tighten.

2. Attach supply tube to spray assembly nipple and to discharge tube as shown.

Moen Incorporated • 25300 Al Moen Drive • North Olmsted, OH 44070-8022 U.S.A. In Canada Moen Inc. • 2816 Bristol Circle • Oakville, Ontario L6H5s7

+ 4 hidden pages