Page 1
INSTALLATION INSTRUCTION
197 - LED Outdoor
WS-W19770
WARNING
IMPORTANT: NEVER attempt any work without shutting o the electricity.
- Read all instructions before installing.
- System is intended for installation by a qualied electrician in accordance with the National Electrical Code and local regulations.
- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF”
the circuit breaker switch(es) that control the power to the xture or room that you are working on.
- Place the wall switch in the “OFF” position.
CAUTION
- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are
worn out or broken. Failure to follow this instruction could invalidate the ETL/CETL listing of this xture.
CAUTION When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.
AVERTISSEMENT
IMPORTANT : Coupez l’électricité avant TOUTE manipulation.
- Lisez toutes les instructions avant d’installer.
- Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et les
règlements locaux.
- Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt
(« OFF »).
- Placez l’interrupteur mural en position d’arrêt (« OFF »).
MISE EN GARDE
- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez pas de côté
et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation ETL/CETL du
luminaire. MISE EN GARDE Ors de la manipulation de l’appareil, ne pas appliquer de pression à la LED, tenir l’appareil par la seule base.
ADVERTENCIA
IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.
- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e insta lación de esta
lámpara.
- Sistema está disenado para ser instalado por un electricista calicado, de acuerdo con el código eléctrico nacional y las normas locales.
- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de ali mentación
principal en la posición “OFF” (APAGADO).
- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).
PRECAUCIÓN
- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación ni
utilice piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calicación
ETL/CETL esta lámpara. PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la base sólo.
HARDWARE
A1 B1 C1 D1 E1 F1 G1 H1 I1
Mounting
Screw
Qty: 4 pcs
+1 Extra
7MPF040902
7MPF040902BK
5/32"-32x3/8 SS
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Wire
Connector
Qty: 3 pcs
+1 Extra
7EAC112201
Junction
Box Screw
Qty: 2 pcs
+1 Extra
7MPF0415C2
#8-32x5/8 SS
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Rubber
Gasket
Qty: 4 pcs
+1 Extra
7TGD060301CL
Allen Wrench
Qty: 1 pc
Allen
Screw
Qty: 1 pc
+1 Extra
7MPF0403K1
5/32"-32x3/16 SS
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Anchor
Qty: 1 pc
+1 Extra
7TDD082401
Iron
Studs
Qty: 1 pc
7MPF2204J2
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Wood
Screw
Qty: 1 pc
+1 Extra
Ø4x22 SS
1Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program.
Page 2
INSTALLATION INSTRUCTION
197 - LED Outdoor
WS-W19770
PREPARATION
1. Shut o the power at the circuit breaker and remove existing xture,
including the crossbar.
2. Carefully unpack your new xture and lay out all the parts on a clear
area. Be careful not to lose any small parts necessary for installation.
CONNECTING THE WIRES (Fig. 2)
3. Remove the mounting screw (A1) and rubber gasket ( D1) from the
xture.
4. Secure mounting plate to the junction box using junction box screws
(C1), the side of the mounting plate marked “GND” must face out.
5. Drill a hole in the wall aligned with the screw tube located on the
xture tail, insert the plastic anchor (G1), fasten the wood screw (I1)
and the iron studs (H1) to the plastic anchor.
6. Connect the transformer input wires with junction box wires as shown
in Fig. 2, making sure that all wire connectors (A1) are secured.
If your outlet box has a green or bare copper ground wire, connect
the xture’s ground wire to it. Otherwise, connect the xture’s ground
wire directly to the mounting plate using the green screw provided.
After wires are connected, tuck them carefully inside the junction box.
MOUNTING THE FIXTURE (Fig. 1)
7. Place the xture over the mounting back plate and secure it with
mounting screws (C1) and rubber gasket ( F1).
8. Insert the screw tube to the iron studs, fasten it with Allen screw (F1)
using the Allen Wrench (E1).
9. To prevent moisture from entering the outlet box and causing a short,
use clear caulking (i.e. indoor/outdoor silicone sealant) to outline the
outside of xture back plate where it meets the wall. Leave a space at
the bottom to allow moisture to escape Fig. 3.
Fig. 2 Wiring
Fig. 3 Sealing
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
Junction
Box
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
Back Plate Dimensions
4 1/8"
1 3/8"
FIG. 1
A1
Mounting Screw
Transformer
Screw Tube
Black Wire
Red Wire
C1
Junction Box Screw
D1
Rubber Gasket
Mounting Plate
E1
B1
Wire Connector
White Wire
Black Wire
Junction Box
Ground Wire
Allen Wrench
F1
Allen Screw
G1
H1
Iron Studs
Plastic
Anchor
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Caulking
1 3/4"
5 3/4"
2 1/8"
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
2 7/8"
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
I1
Wood Screw
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
2Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program.
Loading...