Page 1
INSTALLATION INSTRUCTION
736 - LED Wall Sconce
WS-W73608
WARNING
IMPORTANT: NEVER attempt any work without shutting o the electricity.
- Read all instructions before installing.
- System is intended for installation by a qualied electrician in accordance with the National Electrical Code and local regulations.
- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF”
the circuit breaker switch(es) that control the power to the xture or room that you are working on.
- Place the wall switch in the “OFF” position.
CAUTION
- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are
worn out or broken. Failure to follow this instruction could invalidate the ETL/CETL listing of this xture.
CAUTION When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.
AVERTISSEMENT
IMPORTANT : Coupez l’électricité avant TOUTE manipulation.
- Lisez toutes les instructions avant d’installer.
- Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et les
règlements locaux.
- Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt
(« OFF »).
- Placez l’interrupteur mural en position d’arrêt (« OFF »).
MISE EN GARDE
- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez pas de côté
et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation ETL/CETL du
luminaire. MISE EN GARDE Ors de la manipulation de l’appareil, ne pas appliquer de pression à la LED, tenir l’appareil par la seule base.
ADVERTENCIA
IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.
- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e insta lación de esta
lámpara.
- Sistema está disenado para ser instalado por un electricista calicado, de acuerdo con el código eléctrico nacional y las normas locales.
- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de ali mentación
principal en la posición “OFF” (APAGADO).
- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).
PRECAUCIÓN
- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación ni
utilice piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calicación
ETL/CETL esta lámpara. PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la base sólo.
HARDWARE
A1 B1 C1 D1 E1
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Wire Connector
Qty: 3 pcs
Junction Box Screw
Qty: 2 pcs + 1 Extra
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Mounting Screw
Qty: 1 Extra
Mounting Screw
Qty: 1 Extra
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Gasket
Qty: 1 Extra
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
1Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program.
Page 2
INSTALLATION INSTRUCTION
736 - LED Wall Sconce
WS-W73608
FIG.1
Fixture
Fixture Backplate
Mounting Screw
C1
Ground Wire
Junction Box Screw
B1
Wire Connector
A1
Mounting Plate
Junction Box
Back Plate Dimensions
Gasket
E1
Mounting Screw
D1
1 1/8”
1 3/4”
Ø4”
PREPARATION
1. Shut o the power at the circuit breaker and remove existing xture, including the mounting hardware.
2. Carefully unpack your new xture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.
MOUNTING THE FIXTURE (Fig. 1)
3. Remove the mounting screw (D1) and gasket (E1) from the xture.
4. Remove the mounting screw (C1) from the xture back plate.
5. Secure the mounting plate to the junction box using junction box screws (B1). The side of the mounting back plate marked “GND”
must face out.
CONNECTING THE WIRES (Fig. 2)
6. Connect the xture wires to junction box wires as shown in Fig. 2, making sure that all wire connectors (A1) are secured. If your outlet box
has a green or bare copper ground wire, connect the xture’s ground wire to it. Otherwise, connect the xture’s ground wire directly to the
back plate using the green screw provided. After wires are connected, tuck them carefully inside the junction box.
MOUNTING THE FIXTURE (Fig. 1, 3)
7. Secure the xture back plate to the mounting
plate with mounting screw (C1).
8. Place the xture on the xture back plate, and
secure it with mounting screw (D1) and gasket (E1).
9. To prevent moisture from entering the outlet box
and causing a short, use clear caulking
(i.e. indoor/outdoor silicone sealant) to outline
the outside of xture back plate where it meets
the wall. Leave a space at the bottom to allow
moisture to escape Fig. 3.
Fig.2 Wiring
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Fig.3 Sealing
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
Junction Box
Caulking
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
2Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program.
Page 3
INSTALLATION INSTRUCTION
736 - LED Wall Sconce
WS-W73614/WS-W73620
WARNING
IMPORTANT: NEVER attempt any work without shutting o the electricity.
- Read all instructions before installing.
- System is intended for installation by a qualied electrician in accordance with the National Electrical Code and local regulations.
- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF”
the circuit breaker switch(es) that control the power to the xture or room that you are working on.
- Place the wall switch in the “OFF” position.
CAUTION
- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are
worn out or broken. Failure to follow this instruction could invalidate the ETL/CETL listing of this xture.
CAUTION When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.
AVERTISSEMENT
IMPORTANT : Coupez l’électricité avant TOUTE manipulation.
- Lisez toutes les instructions avant d’installer.
- Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et les
règlements locaux.
- Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt
(« OFF »).
- Placez l’interrupteur mural en position d’arrêt (« OFF »).
MISE EN GARDE
- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez pas de côté
et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation ETL/CETL du
luminaire. MISE EN GARDE Ors de la manipulation de l’appareil, ne pas appliquer de pression à la LED, tenir l’appareil par la seule base.
ADVERTENCIA
IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.
- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e insta lación de esta
lámpara.
- Sistema está disenado para ser instalado por un electricista calicado, de acuerdo con el código eléctrico nacional y las normas locales.
- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de ali mentación
principal en la posición “OFF” (APAGADO).
- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).
PRECAUCIÓN
- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación ni
utilice piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calicación
ETL/CETL esta lámpara. PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la base sólo.
HARDWARE
A1 B1 C1 D1 E1 F1 G1
Wire Connector
Qty: 3 pcs
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Junction Box Screw
Qty: 2 pcs + 1 Extra
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Plastic Anchor
Qty: 2 pcs + 1 Extra
Wood Screw
Qty: 2 pcs + 1 Extra
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Knurled Nut
Qty: 1 Extra
Mounting Screw
Qty: 1 Extra
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Gasket
Qty: 1 Extra
1Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program.
Page 4
INSTALLATION INSTRUCTION
736 - LED Wall Sconce
WS-W73614/WS-W73620
FIG.1
Fixture
Mounting Screw
Fixture Backplate
Junction Box
Wire Connector
A1
Plastic Anchor
C1
Wood Screw
D1
B1
Junction Box Screw
Knurled Nut
E1
Gasket
G1
F1
Mounting Backplate
WS-W73614 - 11 3/4”
WS-W73620 - 16 1/2”
1 3/4”
WS-W73614 - 8 5/8”
WS-W73620 - 11 3/4”
1 1/8”
Back Plate Dimensions
PREPARATION
1. Shut o the power at the circuit breaker and remove existing xture, including the mounting hardware.
2. Carefully unpack your new xture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.
MOUNTING THE FIXTURE (Fig. 1)
3. Remove the mounting screw (G1) and gasket (F1) from the xture.
4. Remove the knurled nut (E1) from the xture back plate.
5. Drill a hole in the wall aligned with the key-hole located in the mounting back plate, insert the plastic anchor (C1).
6. Secure the mounting back plate to the junction box using junction box screws (B1). Fasten the mounting back plate to the wall using the
wood screw (D1). The side of the mounting back plate marked “GND” must face out.
CONNECTING THE WIRES (Fig. 2)
7. Connect the xture wires to junction box wires as shown in Fig. 2, making sure that all wire connectors (A1) are secured. If your outlet box
has a green or bare copper ground wire, connect the xture’s ground wire to it. Otherwise, connect the xture’s ground wire directly to the
back plate using the green screw provided. After wires are connected, tuck them carefully inside the junction box.
MOUNTING THE FIXTURE (Fig. 1, 3)
8. Secure the xture back plate to the mounting
plate with knurled nut (E1).
9. Place the xture on the xture back plate, and
secure it with mounting screw (F1) and gasket (G1).
10. To prevent moisture from entering the outlet box
and causing a short, use clear caulking
(i.e. indoor/outdoor silicone sealant) to outline
the outside of xture back plate where it meets
the wall. Leave a space at the bottom to allow
moisture to escape Fig. 3.
Fig.2 Wiring
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
H
ouse Wires
Green or Bare Copper
(Ground)
Fig.3 Sealing
Junction Box
Caulking
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
2Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program.
Loading...