Modern Forms MFDE1237 Installation & Assembly

INSTALLATION INSTRUCTION

136 - Vanities & Sconces

WS-13619/WS-13630/WS-13641

WARNING

IMPORTANT: NEVER attempt any work without shutting o the electricity.

- Read all instructions before installing.

- System is intended for installation by a qualied electrician in accordance with the National Electrical Code and local regulations.

- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF”
the circuit breaker switch(es) that control the power to the xture or room that you are working on.

- Place the wall switch in the “OFF” position.

CAUTION

- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are
worn out or broken. Failure to follow this instruction could invalidate the ETL/CETL listing of this xture.
CAUTION When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.

AVERTISSEMENT

IMPORTANT : Coupez l’électricité avant TOUTE manipulation.

- Lisez toutes les instructions avant d’installer.

- Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et les
règlements locaux.

- Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt
(« OFF »).

- Placez l’interrupteur mural en position d’arrêt (« OFF »).

MISE EN GARDE

- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez pas de côté
et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation ETL/CETL du
luminaire. MISE EN GARDE Ors de la manipulation de l’appareil, ne pas appliquer de pression à la LED, tenir l’appareil par la seule base.

ADVERTENCIA

IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.

- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e insta lación de esta
lámpara.

- Sistema está disenado para ser instalado por un electricista calicado, de acuerdo con el código eléctrico nacional y las normas locales.

- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de ali mentación
principal en la posición “OFF” (APAGADO).

- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).

PRECAUCIÓN

- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación ni
utilice piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calicación
ETL/CETL esta lámpara. PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la base sólo.

HARDWARE

A1 G1F1E1D1C1B1

Wire Connector

Qty: 3 pcs

modernforms.com

Phone [phone]
Fax [phone]

Mounting Screw

Qty: 3 pcs

+ 1 Extra

Headquarters/Eastern Distribution Center

44 Harbor Park Drive
Port Washington, NY 11050

Junction Box Screw

Qty: 2 pcs

+ 1 Extra

Plastic Anchor

Qty: 2 pcs

Wood Screw

Qty: 2 pcs

Central Distribution Center

1600 Distribution Ct
Lithia Springs, GA 30122

Allen Screw

Qty: 1 pc Per Glass

+ 1 Extra

Western Distribution Center

1750 Archibald Avenue
Ontario, CA 91760

Wire Connector

Qty: 1 pc

1Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program.

INSTALLATION INSTRUCTION

136 - Vanities & Sconces

WS-13619/WS-13630/WS-13641

FIG.1

Plastic Anchor

Glass Box

Wood Screw

E1

Back Plate Dimensions

5 3/4”

4 1/2”

D1

Mounting Screw

Junction Box Screw

Glass

1 3/8”

C1

B1

Junction Box

Wire Connector

A1

Mounting Plate

Ground Screw

F1

Allen Screw

Allen Wrench

G1

1 3/4”

PREPARATION

1. Shut o the power at the circuit breaker and remove existing xture, including the mounting hardware.

2. Carefully unpack your new xture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for installation.

MOUNTING THE FIXTURE (Fig. 1)

3. Remove the mounting screw (B1) from the xture.

4. Drill a hole in the wall aligned with the key holes located in the glass box, insert the plastic anchor (D1) to the wall.

5. Secure the mounting plate to the junction box using junction box screw (C1). The side of the mounting back plate marked

“GND” must face out.

CONNECTING THE WIRES (Fig. 2)

6. Connect the xture wires to junction box wires as shown in Fig. 2, making sure that all wire connectors (A1) are secured. If your outlet box
has a green or bare copper ground wire, connect the xture’s ground wire to it. Otherwise, connect the xture’s ground wire directly to the
back plate using the green screw provided. After wires are connected, tuck them carefully inside the junction box.

MOUNTING THE FIXTURE (Fig. 1)

7. Place the xture on the mounting plate, and secure it with
mounting screw (B1). Fasten the xture to the wall using the
wood screw (E1).

8. Insert the glass to the glass box, and secure it with Allen screw (F1)
using Allen wrench (G1) provided.

Fig.2 Wiring

Fixture Wires

Black or
Smooth

Fixture Wires

White or
Ribbed

Fixture Wires

Bare wire
(Ground)

House Wires

Black
(Hot)

House Wires

White
(Neutral)

House Wires

Green or Bare Copper
(Ground)

modernforms.com

Phone [phone]
Fax [phone]

Headquarters/Eastern Distribution Center

44 Harbor Park Drive
Port Washington, NY 11050

Central Distribution Center

1600 Distribution Ct
Lithia Springs, GA 30122

Western Distribution Center

1750 Archibald Avenue
Ontario, CA 91760

2Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program.