Modern Forms MFDE1091 Installation & Assembly

INSTALLATION INSTRUCTION

(Please direct wire with 120V AC)

Urban

WS-W1116, WS-W1122

WARNING

IMPORTANT: NEVER attempt any work without shutting o the electricity.

- Read all instructions before installing.

- System is intended for installation by a qualied electrician in accordance with the National Electrical Code and local
regulations.

- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or
switch ”OFF” the circuit breaker switch(es) that control the power to the xture or room that you are working on.

- Place the wall switch in the “OFF” position.

CAUTION

- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts
that are worn out or broken. Failure to follow this instruction could invalidate the ETL/CETL listing of this xture.
CAUTION When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.

AVERTISSEMENT

IMPORTANT : Coupez l’électricité avant TOUTE manipulation.

- Lisez toutes les instructions avant d’installer.

- Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et les
règlements locaux.

- Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en
position d’arrêt (« OFF »).

- Placez l’interrupteur mural en position d’arrêt (« OFF »).

MISE EN GARDE

- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en
laissez pas de côté et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler
l’homologation ETL/CETL du luminaire. MISE EN GARDE Ors de la manipulation de l’appareil, ne pas appliquer de pression
à la LED, tenir l’appareil par la seule base.

ADVERTENCIA

IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.

- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e insta
lación de esta lámpara.

- Sistema está disenado para ser instalado por un electricista calicado, de acuerdo con el código eléctrico nacional
y las normas locales.

- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de ali
mentación principal en la posición “OFF” (APAGADO).

- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).

PRECAUCIÓN

- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la
instalación ni utilice piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calicación
ETL/CETL esta lámpara. PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la
base sólo.

HARDWARE

Driver

Modern Forms

www.modernforms.com
Phone [phone] • Fax [phone]

Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. SEPTEMBER, 2014

Technology Upgraded
No Driver Required

A1 B1 C1 H1 C1

Wire Connector
Qty: 3

Headquarters/Eastern Distribution Center

44 Harbor Park Drive • Port Washington, NY 11050
Phone [phone] • Fax [phone]

Junction Box Screw
Qty: 2 + 1 Extra

Fixture Screw
Qty: 1 Extra

Western Distribution Center

1750 Archibald Ave • Ontario, CA 91761
Phone [phone] • Fax [phone]

Mounting Screw
Qty: 2

Anchor
Qty: 2

INSTALLATION INSTRUCTION

Urban

WS-W1116, WS-W1122

FIG.1

G1

Gasket

C1

Fixture Screw

H1

Mounting
Screw

J1

Anchor

K1

Junction Box
Screw

F1

Junction
Box

C1

Fixture Screw

H1

Mounting
Screw

Junction
Box Screw

E1B1

Green
Screw

J1

Anchor

Mounting
backplate

K1

Junction Box
Screw

A1D1

Wire
Connector

PREPARATION

1. Shut o the power at the circuit breaker and remove existing xture, including the crossbar.

2. Carefully unpack your new xture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary
for installation

3. Remove mounting screws (C1)

4. Connect xture wires to junction box wires as shown in Fig. 2 making sure all wire connectors are secured. Fixture and junction
box ground wires should be connected to mounting plate using green screw provided. After wires are connected, tuck them
carefully inside the junction box.

5. Secure mounting backplate (D1) to the junction box (F1) using junction box screws (B1). The side of the mounting backplate
marked “GND” must face out.

6. Drill holes in the wall aligned with the keyholes locations on the Fixture back plate insert anchors.

7. Place the xture’s backplate over the mounting backplate (D1) and secure with screws (G1).

8. Secure xture back plate with screws (H1) into anchors (J1)

9. Mount xture body to the xture back plate using screw (C1) and gaskets (G1)

COMPLETING THE INSTALLATION (Fig. 3)

10. To prevent moisture from entering the outlet box and causing a short, use clear caulking (i.e. indoor/outdoor silicone sealant)
to outline the outside of xture backplate where it meets the wall. Leave a space at bottom to allow moisture a means to escape.

Fig.2 Wiring

Fixture Wires

Black or
Smooth

Fixture Wires

White or
Ribbed

Fixture Wires

Bare wire
(Ground)

Modern Forms

www.modernforms.com
Phone [phone] • Fax [phone]

Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. SEPTEMBER, 2014

House Wires

Black
(Hot)

House Wires

White
(Neutral)

House Wires

Green or Bare Copper
(Ground)

Headquarters/Eastern Distribution Center

44 Harbor Park Drive • Port Washington, NY 11050
Phone [phone] • Fax [phone]

Fig.3 Sealing

Junction Box

Caulking

Western Distribution Center

1750 Archibald Ave • Ontario, CA 91761
Phone [phone] • Fax [phone]