Modern Forms MFDE1082 Installation & Assembly

INSTALLATION INSTRUCTION

BDSM

PD-51542

WARNING

IMPORTANT: NEVER attempt any work without shutting o the electricity.

- Read all instructions before installing.

- System is intended for installation by a qualied electrician in accordance with the National Electrical Code and local
regulations.

- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or
switch ”OFF” the circuit breaker switch(es) that control the power to the xture or room that you are working on.

- Place the wall switch in the “OFF” position.

CAUTION

- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts
that are worn out or broken. Failure to follow this instruction could invalidate the ETL/CETL listing of this xture.
CAUTION When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.

AVERTISSEMENT

IMPORTANT : Coupez l’électricité avant TOUTE manipulation.

- Lisez toutes les instructions avant d’installer.

- Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et les
règlements locaux.

- Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en posi
tion d’arrêt (« OFF »).

- Placez l’interrupteur mural en position d’arrêt (« OFF »).

MISE EN GARDE

- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en
laissez pas de côté et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler
l’homologation ETL/CETL du luminaire. MISE EN GARDE Ors de la manipulation de l’appareil, ne pas appliquer de pression
à la LED, tenir l’appareil par la seule base.

ADVERTENCIA

IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.

- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e insta
lación de esta lámpara.

- Sistema está disenado para ser instalado por un electricista calicado, de acuerdo con el código eléctrico nacional
y las normas locales.

- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de ali
mentación principal en la posición “OFF” (APAGADO).

- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).

PRECAUCIÓN

- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la
instalación ni utilice piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calicación
ETL/CETL esta lámpara. PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la
base sólo.

HARDWARE

Modernforms

www.modernforms.com
Phone [phone] • Fax [phone]

Modernforms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. MAY, 2014

C1 E1 B1 F1 H1

Headquarters/Eastern Distribution Center

44 Harbor Park Drive • Port Washington, NY 11050
Phone [phone] • Fax [phone]

Western Distribution Center

1750 Archibald Ave • Ontario, CA 91761
Phone [phone] • Fax [phone]

INSTALLATION INSTRUCTION

BDSM

PD-51542

PREPARATION

1. Shut o the power at the circuit breaker and remove
existing xture, including the mounting hardware.

2. Carefully unpack your new xture and lay out
all the parts on a clear area. Be careful not to lose
any small parts necessary for installation.

MOUNTING THE FIXTURE (FIG.1)

3. Drill holes in the ceiling aligned with the key
hole location in the mounting plate (D1).

4. Insert the mounting anchors (B1) into holes.

5. Secure the mounting plate (D1) to the junction
box (A1) using junction box screws (E1). The side of the
mounting plate marked “GND” must face out.

6. Fasten the wood screws (F1) into the mounting
anchors (B1) and tighten.

7. Slide the glass (L1) into the xture (J1).

8. On each end of xture, angle-in the end caps (K1)
and press in to secure.

FIG.1

A1

B1

C1

D1

E1

F1

N1

H1

G1

J1

I1

K1

J1

K1

9. Adjust the xture wire length by pressing the
cable-grippers (I1) on canopy and pulling the wire.
Make sure the wires are the same length.

10. Re-set the strain relief (N1) near the wiring holes.

CONNECTING THE WIRES (FIG.2)

11. Connect the transformer input wires with supply wires
as shown in Fig. 2, making sure that all wire connectors
(C1) are secured.

12. Cut the xture wires and leaving at least 6”. Connect
with the transformer output wires red).

Note: The xture wires have two braided layers.
Strip the two layers carefully!

If your outlet box has a ground wire, connect it to the
xture’s ground wire. Otherwise, connect the xture’s
ground wire directly to the mounting plate (D1) using
the green screw provided. Tuck wires carefully inside the
junction box.

13. Place the canopy (G1) over the mounting plate (D1),
secure with screws (H1).

14. Check if xture is level and adjust cables if necessary.

FIG.2

Fixture Wires

Black or
Smooth

Fixture Wires

White or
Ribbed

Fixture Wires

Bare Copper
(Ground)

House Wires

Black
(Hot)

House Wires

White
(Neutral)

House Wires

Green or Bare Copper
(Ground)

L1

Modernforms

www.modernforms.com
Phone [phone] • Fax [phone]

Modernforms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. MAY, 2014

Headquarters/Eastern Distribution Center

44 Harbor Park Drive • Port Washington, NY 11050
Phone [phone] • Fax [phone]

Western Distribution Center

1750 Archibald Ave • Ontario, CA 91761
Phone [phone] • Fax [phone]