Modern Forms MFDE1044 Installation & Assembly

INSTALLATION INSTRUCTION

Vetri

WS-3919, WS-3925, WS-3937

WARNING

IMPORTANT: NEVER attempt any work without shutting o the electricity.

- Read all instructions before installing.

- System is intended for installation by a qualied electrician in accordance with the National Electrical Code and local
regulations.

- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or
switch ”OFF” the circuit breaker switch(es) that control the power to the xture or room that you are working on.

- Place the wall switch in the “OFF” position.

CAUTION

- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts
that are worn out or broken. Failure to follow this instruction could invalidate the ETL/CETL listing of this xture.
CAUTION When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.

AVERTISSEMENT

IMPORTANT : Coupez l’électricité avant TOUTE manipulation.

- Lisez toutes les instructions avant d’installer.

- Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et les
règlements locaux.

- Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en
position d’arrêt (« OFF »).

- Placez l’interrupteur mural en position d’arrêt (« OFF »).

MISE EN GARDE

- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en
laissez pas de côté et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler
l’homologation ETL/CETL du luminaire. MISE EN GARDE Ors de la manipulation de l’appareil, ne pas appliquer de pression
à la LED, tenir l’appareil par la seule base.

ADVERTENCIA

IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.

- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e insta
lación de esta lámpara.

- Sistema está disenado para ser instalado por un electricista calicado, de acuerdo con el código eléctrico nacional
y las normas locales.

- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de ali
mentación principal en la posición “OFF” (APAGADO).

- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).

PRECAUCIÓN

- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la
instalación ni utilice piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calicación
ETL/CETL esta lámpara. PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la
base sólo.

HARDWARE

A1 B1 C1 D1 E1

Wire Connector
Qty: 3

Modern Forms

www.modernforms.com
Phone [phone] • Fax [phone]

Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. SEPTEMBER, 2014

Junction Box Screw
Qty: 2 + 1 Extra

Headquarters/Eastern Distribution Center

44 Harbor Park Drive • Port Washington, NY 11050
Phone [phone] • Fax [phone]

Mounting Screw
Qty: 2 + 1 Extra

Nut
Qty: 3

Western Distribution Center

1750 Archibald Ave • Ontario, CA 91761
Phone [phone] • Fax [phone]

Plastic Washer
Qty: 3

INSTALLATION INSTRUCTION

Vetri

WS-3919, WS-3925, WS-3937

FIG.1

D1 E1

Fixture Back Plate

M1

G1

Connectors

Red Wire

K1

B1

H1

Blue Wire

C1

Transformer Output
Wires - Red

PREPARATION

1. Shut o the power at the circuit breaker and remove existing xture, including the crossbar.

Junction Box

A1

J1

Transformer

I1

Mounting Backplate

F1

L1

Ground Wire

2. Carefully unpack your new xture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary
for installation.

CONNECTING THE WIRES (Fig. 2)

3. Remove screws (C1) from the xture. Remove connectors (K1).

4. Connect the transformer input wires to junction box wires as shown in Fig. 2, making sure that all wire connectors (A1) are
secured. If your outlet box has a ground wire (L1) (green or bare copper), connect the xture’s ground wire to it. Otherwise,
connect the xture’s ground wire directly to the back plate (I1) using the green screw (H1) provided. After wires are connected,
tuck them carefully inside the junction box. *Requires Transformer to be recessed within the junction box

MOUNTING THE FIXTURE (Fig. 1)

5. Secure mounting backplate (I1) to the junction Box (F1) using junction box screws (B1).
The side of the mounting backplate marked “GND” (H1) must face out.

6. Connect the xture’s wires (Blue & Red) to the Transformer’s (J1)
output wires (Red and Red) – Blue to Red and Red to the other Red.

7. Place the xture’s canopy plate (M1) over the mounting back plate (I1)
and secure with screws (C1).

8. Install the glass (G1) on the front of xture with
screws (D1) and plastic washer (E1).

Fig.2 Wiring

Fixture Wires

Black or
Smooth

Fixture Wires

White or
Ribbed

Fixture Wires

Bare wire
(Ground)

House Wires

Black
(Hot)

House Wires

White
(Neutral)

House Wires

Green or Bare Copper
(Ground)

Modern Forms

www.modernforms.com
Phone [phone] • Fax [phone]

Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. SEPTEMBER, 2014

Headquarters/Eastern Distribution Center

44 Harbor Park Drive • Port Washington, NY 11050
Phone [phone] • Fax [phone]

Western Distribution Center

1750 Archibald Ave • Ontario, CA 91761
Phone [phone] • Fax [phone]