Modern Forms MFDE1013 Installation & Assembly

INSTALLATION INSTRUCTION

(Please direct wire with 120V AC)

TWILIGHT

WS-W5516, W5521

WARNING

IMPORTANT: NEVER attempt any work without shutting o the electricity.

- Read all instructions before installing.

- System is intended for installation by a qualied electrician in accordance with the National Electrical Code and local
regulations.

- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or
switch ”OFF” the circuit breaker switch(es) that control the power to the xture or room that you are working on.

- Place the wall switch in the “OFF” position.

CAUTION

- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts
that are worn out or broken. Failure to follow this instruction could invalidate the ETL/CETL listing of this xture.
CAUTION When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.

AVERTISSEMENT

IMPORTANT : Coupez l’électricité avant TOUTE manipulation.

- Lisez toutes les instructions avant d’installer.

- Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et les
règlements locaux.

- Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en posi
tion d’arrêt (« OFF »).

- Placez l’interrupteur mural en position d’arrêt (« OFF »).

MISE EN GARDE

- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en
laissez pas de côté et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler
l’homologation ETL/CETL du luminaire. MISE EN GARDE Ors de la manipulation de l’appareil, ne pas appliquer de pression
à la LED, tenir l’appareil par la seule base.

ADVERTENCIA

IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.

- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e insta
lación de esta lámpara.

- Sistema está disenado para ser instalado por un electricista calicado, de acuerdo con el código eléctrico nacional
y las normas locales.

- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de ali
mentación principal en la posición “OFF” (APAGADO).

- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).

PRECAUCIÓN

- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la
instalación ni utilice piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calicación
ETL/CETL esta lámpara. PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la
base sólo.

HARDWARE

Driver

Modern Forms

www.modernforms.com
Phone [phone] • Fax [phone]

Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. SEPTEMBER, 2014

Technology Upgraded
No Driver Required

A1 B1 G1

Wire Connector
Qty: 3

Headquarters/Eastern Distribution Center

44 Harbor Park Drive • Port Washington, NY 11050
Phone [phone] • Fax [phone]

Junction Box
Screw
Qty: 2 + 1 Extra

Mounting Screw
Qty: 2 + 1 Extra

Western Distribution Center

1750 Archibald Ave • Ontario, CA 91761
Phone [phone] • Fax [phone]

INSTALLATION INSTRUCTION

TWILIGHT

WS-W5516, W5521

PREPARATION

1. Shut o the power at the circuit breaker and remove
existing xture, including the mounting hardware.

2. Carefully unpack your new xture and lay out all the parts
on a clear area. Be careful not to lose any small parts
necessary for installation.

MOUNTING THE FIXTURE (FIG.1)

3. Secure the mounting plate (D1) to the junction box (F1)
using junction box screws (B1). The side of the mounting
plate marked “GND” must face out.

CONNECTING THE WIRES (FIG.2)

4. Connect the electrical wires as shown in Fig. 2, making
sure that all wire connectors (A1) are secured. Fixture and
junction box ground wires should be connected to
mounting plate using green screw provided.
Tuck wires carefully inside the junction box.

5. Place the xture’s back plate over the mounting plate (D1)
and secure with screws (G1) and gasket (C1).

6. If desired, the decorative insert may be removed by
unscrewing the nut (H1) from the back of the xture

COMPLETING INSTALLATION (FIG.3)

7. To prevent moisture from entering the outlet box and
causing a short, use clear caulking (i.e. indoor/outdoor
silicone sealant) to outline the outside of xture back plate
where it meets the wall. Leave a space at the bottom to
allow moisture to escape (Fig.3).

100%-10% DIMMING
COMPATIBLE WITH THE FOLLOWING ELECTRONIC

LOW VOLTAGE (ELV) DIMMERS

Brand Model
LUTRON SELV-300P
LUTRON DVELV-300P
LEVITON MLE03-1

FIG.1

Fig.2 Wiring

Fig.3 Sealing

C1

Gasket

Fixture Wires

Black or
Smooth

Fixture Wires

White or
Ribbed

Fixture Wires

Bare wire
(Ground)

Junction Box

Junction Box

F1

C1

Gasket

Screw

G1

D1

Mounting Plate

B1

Junction Box Screw

G1

Fixture Screw

House Wires

Black
(Hot)

House Wires

White
(Neutral)

House Wires

Green or Bare Copper
(Ground)

H1

Nut

A1

Wire
Connector

Caulking

Modern Forms

www.modernforms.com
Phone [phone] • Fax [phone]

Modern Forms retains the right to modify the design of our products at any time as part of the company's continuous improvement program. SEPTEMBER, 2014

Headquarters/Eastern Distribution Center

44 Harbor Park Drive • Port Washington, NY 11050
Phone [phone] • Fax [phone]

Western Distribution Center

1750 Archibald Ave • Ontario, CA 91761
Phone [phone] • Fax [phone]