Page 1
INSTALLATION INSTRUCTION
Elessar - LED Wall Sconce
WS-66641
WARNING
IMPORTANT: NEVER attempt any work without shutting o the electricity.
- Read all instructions before installing.
- System is intended for installation by a qualied electrician in accordance with the National Electrical Code and local regulations.
- Go to the main fuse box, or circuit breaker. Place the main power switch in the “OFF” position and unscrew the fuse(s) or switch ”OFF”
the circuit breaker switch(es) that control the power to the xture or room that you are working on.
- Place the wall switch in the “OFF” position.
CAUTION
- All parts must be used as indicated in these instructions. Do not substitute any parts, leave parts out, or use any parts that are
worn out or broken. Failure to follow this instruction could invalidate the ETL/CETL listing of this xture.
CAUTION When handling the xture, do not apply pressure to the LEDs. Hold the xture by the base only.
AVERTISSEMENT
IMPORTANT : Coupez l’électricité avant TOUTE manipulation.
- Lisez toutes les instructions avant d’installer.
- Système est destiné à être installé par un électricien qualié en conformité avec le code national de l’électricité et les
règlements locaux.
- Accédez au panneau central de disjoncteurs ou de fusibles de votre demeure et placez l’interrupteur principal en position d’arrêt
(« OFF »).
- Placez l’interrupteur mural en position d’arrêt (« OFF »).
MISE EN GARDE
- Toutes les pièces doivent être utilisées tel qu’il est indiqué dans ces instructions. Ne remplacez pas les pièces, n’en laissez pas de côté
et ne les utilisez pas si elles sont usées ou brisées. Le non-respect de ces instructions peut annuler l’homologation ETL/CETL du
luminaire. MISE EN GARDE Ors de la manipulation de l’appareil, ne pas appliquer de pression à la LED, tenir l’appareil par la seule base.
ADVERTENCIA
IMPORTANTE: NUNCA intente hacer trabajos sin desconectar el suministro eléctrico.
- Lea y comprenda todas las instrucciones e ilustraciones por completo antes de proceder con el ensamblaje e insta lación de esta
lámpara.
- Sistema está disenado para ser instalado por un electricista calicado, de acuerdo con el código eléctrico nacional y las normas locales.
- Diríjase a la caja de fusibles o a la caja del interruptor de circuito principal en su hogar. Coloque el interruptor de ali mentación
principal en la posición “OFF” (APAGADO).
- Coloque el interruptor de la pared en la posición “OFF” (APAGADO).
PRECAUCIÓN
- Todas las piezas deben usarse como lo indican estas instrucciones. No reemplace las piezas, noomita piezas durante la instalación ni
utilice piezas gastadas o rotas. El incumplimiento de esta indicación podría invalidar la calicación
ETL/CETL esta lámpara. PRECAUCIÓN Al manipular el aparato, no aplique presión a los LED, mantenga el aparato en la base sólo.
HARDWARE HDW66641ELESSAR
A1 B1 C1 D1 E1 F1 G1 H1 J1
Wire
Connector
Qty: 2 pcs
+ 1 Extra
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Modern Forms retains the right to modify the design of our products at any time as part of the company’s continuous improvement program.
Junction
Box Screw
Qty: 2 pcs
+ 1 Extra
Mounting
Screw
Qty: 1 Extra
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Anchor
Qty: 1 pc
+ 1 Extra
Wood
Screw
Qty: 1 pc
1 Extra
Allen
Wrench
Qty: 1 pc
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
Allen
Screw
Qty: 1 pc
+ 1 Extra
Iron
Studs
Qty: 1 pc
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
Screw
Qty: 2 pcs
+ 1 Extra
1
Page 2
INSTALLATION INSTRUCTION
Elessar - LED Wall Sconce
WS-66641
PREPARATION
1. Shut o the power at the circuit breaker and remove existing
xture, including the crossbar.
2. Carefully unpack your new xture and lay out all the parts on
a clear area. Be careful not to lose any small parts necessary
for installation.
CONNECTING THE WIRES Fig. 2
3. Remove the mounting screw (C1) from the xture.
4. Connect the driver input wires with junction box wires as
shown in Fig. 2, making sure that all wire connectors (A1)
are secured. If your outlet box has a green or bare copper
ground wire, connect the xture’s ground wire to it.
Otherwise, connect the xture’s ground wire directly to the
mounting plate using the green screw provided. After wires
are connected, tuck them carefully inside the junction box.
*Require Driver to be recessed within the junction box.
MOUNTING THE FIXTURE Fig. 1
5. Secure mounting plate to the junction box using junction
box screws (B1), the side of the mounting plate marked “GND”
must face out.
6. Drill a hole in the wall aligned with the screw tube located on
the xture tail, insert the plastic anchor (D1), fasten the wood
screw (E1) and the iron studs (H1) to the plastic anchor.
7. Insert the crystal onto the xture, secure it with screw (J1).
8. Place the xture over the mounting back plate and secure it
with mounting screws (C1).
9. Insert the screw tube to the iron studs, fasten it with
Allen screw (G1) using the Allen Wrench (F1).
Fig. 2 Wiring
Fixture Wires
Brown
House Wires
Hot
FIG.1
C1
Mounting Screw
J1
Screw
Red Wire
Fixture
Screw Tube
Black Wire
White Wire
Black Wire
Driver
Mounting Backplate
B1
Junction Box Screw
A1
Wire Connector
Ground Wire
E1
Wood Screw
H1
D1
Junction
Box
Iron Studs
Plastic Anchor
Fixture Wires
Blue
Fixture Wires
Yellow Green
House Wires
Neutral
House Wires
Ground Wire
Back Plate Dimensions
4”
3 1/2”
5 1/2”
modernforms.com
Phone (800) 526.2588
Fax (800) 526.2585
Modern Forms retains the right to modify the design of our products at any time as part of the company’s continuous improvement program.
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
Central Distribution Center
1600 Distribution Ct
Lithia Springs, GA 30122
G1
Allen Screw
F1
Allen Wrench
Western Distribution Center
1750 Archibald Avenue
Ontario, CA 91760
2
Loading...