USER’S GUIDE
SRCD2731BT
HOME MUSIC SYSTEM
PLEASE READ BEFORE OPERATING THIS EQUIPMENT
Warnings and Precautions
• CAUTION: TO PREVENT ELECTRIC SHOCK,
MATCH WIDE BLADE OF PLUG TO WIDE SLOT,
FULLY INSERT.
•
WARNING:To reduce the risk of re or electric shock,
do not expose this apparatus to rain or moisture.
• AVERTISSEMENT: Pour réduire le risque d’incendie
ou de choc électrique, ne pas exposer cet appareil sous la
pluie et l’humidité.
• CAUTION: Use of any controls or adjustments or
performance of procedures other than those herein
specied may result in hazardous radiation exposure.
• WARNING: Changes or modications to this unit
not expressly approved by the party responsible for
compliance could void the user’s authority to operate the
equipment.
• WARNING: Do not place this unit directly onto
furniture surfaces with any type of soft, porous, or
sensitive nish. As with any rubber compound made with
oils, the feet could cause marks or staining where the feet
reside. We recommend using a protective barrier such
as a cloth or a piece of glass between the unit and the
surface to reduce the risk of damage and/or staining.
• WARNING: Use of this unit near uorescent lighting
may cause interference regarding use of the remote. If
the unit is displaying erratic behavior move away from
any uorescent lighting, as it may be the cause.
CAUTION:Danger of explosion if battery is incorrectly
•
replaced. Replace only with the same or equivalent type.
• PRÉCAUTION: Danger d’explosion si les piles sont
remplacées de façon incorrect. Remplacer les piles
seulement par le même type de pile ou l’équivalent.
• WARNING: There is a danger of explosion if you
attempt to charge standard Alkaline batteries in the unit.
Only use rechargeable NiMH batteries.
• WARNING: The remote control’s button cell battery
contains mercury. Do not put in the trash, instead recycle
or dispose of as hazardous waste
WARNING: The remote control supplied with this
product contains a button-cell battery that could be
accidentally ingested by children. Do not leave button-cell
batteries accessible to children. If swallowed, promptly
see doctor and call (202) 625-3333.
• WARNING:Lithium batteries, like all rechargeable
batteries are recyclable and should be recycled or
disposed of in normal household waste. Contact your
local government for disposal or recycling practices in
your area. They should never be incinerated since they
might explode.
• WARNING: Shock hazard - Do Not Open.
• AVIS: RISQUE DE CHOC ÉLECTRIQUE - NE PAS
OUVRIR
Mains plug is used as disconnect device and it should
remain readily operable during intended use. In order
to disconnect the apparatus from the mains completely,
the mains plug should be disconnected from the mains
socket outlet completely.
La prise du secteur est utilisé pour déconnecter le
système.
La prise du secteur ne doit pas être obstruée ou doit être
facilement accessible pendant son utilisation. Pour être
complètement déconnecté de l’alimentation d’entrée, la
prise doit être débranchée du secteur.
Do not mix old and new batteries.
Do not mix alkaline, standard (carbon-zinc), or
rechargeable (ni-cad, ni-mh, etc) batteries.
No mezcle baterías viejas y nuevas.
No mezcle baterías alcalinas, estándar (carbono-zinc) o
recargables (ni-cad, ni-mh, etc.).
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
ATTENTION
RISQUE D' ÉLECTROCUTION
NE PAS OUVRIR
WARNING: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USERSERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The lightning ash with arrowhead symbol, within
an equilateral triangle, is intended to alert the user
to the presence of uninsulated "dangerous voltage"
within the product's enclosure that may be of
sufcient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral triangle
is intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
appliance.
This product utilizes a Class 1 laser to read
Compact Discs. This laser Compact Disc Player is
equipped with safety switches to avoid exposure
when the CD door is open and the safety interlocks
are defeated. Invisible laser radiation is present
when the CD Player’s lid is open and the system’s
interlock has failed or been defeated. It is very
important that you avoid direct exposure to the
laser beam at all times. Please do not attempt to
defeat or bypass the safety switches.
2
Important Safety Instructions
1. Read these Instructions.
2. Keep these Instructions.
3. Heed all Warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
ampliers) that produce heat.
9. Do not defeat the safety purpose of the polarized or
grounding - type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety.
When the provided plug does not t into your outlet,
consult an electrician for replacement of the obsolete
outlet.
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11. Only use attachments/accessories specied by the
manufacturer.
12.
Use only with a cart, stand, tripod,
bracket, or table specied by the
manufacturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination to
avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when
unused for long periods of time.
Refer all servicing to qualified service personnel.
14.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate
normally, or has been dropped.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference,
and (2) this device must accept any interference
received, including interference that may cause
undesired operation.
FCC Warnings
WARNING: Changes or modications to this unit not expressly
approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from
•
that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
The device has beem evaluated to meet general RF exposure requirement.
The device can be used in portable exposure condition without restriction.
To maintain compliance with FCC’s RF Exposure guidelines, This
equipment should be installed and operated with minimum distance
between 20cm the radiator your body: Use only the supplied antenna.
Additional Warnings
• The apparatus shall not be exposed to dripping or splashing and
that no objects lled with liquids, such as vases, shall be placed on
apparatus.
L’appareil ne doit pas être exposé aux écoulements ou aux
éclaboussures et aucun objet ne contenant de liquide, tel qu’un vase,
ne doit être placé sur l’objet.
• Main plug is used as disconnect device and it should remain readily
operable during intended use. In order to disconnect the apparatus
from the mains completely, the mains plug should be disconnected
form the mains socket outlet completely.
La prise du secteur ne doit pas être obstruée ou doit être facilement
accessible pendant son utilisation. Pour être complètement
déconnecté de l’alimentation d’entrée, la prise doit être débranchée
du secteur.
• Battery shall not be exposed to excessive heat such as sunshine, re
or the like.
Les piles ne doivent pas être exposées à de forte chaleur, tel qu’à la
lumière du soleil, au feu ou autres choses de semblable.
• Caution marking is located at the rear or back of the apparatus.
Attention marquage est situé à l’arrière ou à l’arrière de l’appareil
• The marking information is located at the rear or back of apparatus.
Les informations de marquage est situé à l’arrière ou à l’arrière de
l’appareil.
This symbol indicates that this product
incorporates double insulation between
hazardous mains voltage and user
accessible parts.
3
Introduction
STANDBY INDICATOR
LED light up indicated
Standby mode.
POWER
Press to power the
music system off or on.
LCD DISPLAY
Press to switch the preset
EQ to Pop, Jazz, Classic,
Rock or Normal.
Press to switch to CD, LINE
IN, Radio or Bluetooth
EQ
SOURCE
modes.
3.5MM AUDIO INPUT
3.5MM HEADPHONE
INPUT
REMOTE SENSOR
Press the cycle through saved
MEM(+/-)
radio stations.
CD COMPARTMENT
VOLUME
Turn to adjust the volume
up or down.
OPEN/CLOSE
Press to open or close
the CD door.
PAIRING/PLAY/PAUSE
Press to play or pause a
loaded CD.
Press & hold to begin
pairing a Bluetooth device.
STOP
Press to stop a CD
during play.
SKIP/SEARCH/TUNE(+/-)
Press to skip between tracks
on loaded CD or Bluetooth.
Press and hold to search
through an individual track.
Press to tune the FM radio.
Press to adjust the time
when setting the clock.
REPEAT
Press to repeat the
current track or an
entire album/playlist.
MEN/CLK SET
Press to set the clock or
save a radio station.
PROGRAM
Press to program a loaded
disc to play tracks in a
specified order.
SPEAKER TERMINAL
Connected to external
DC POWER INPUT
4
speakers
FM ANTENNA WIRE
.
PAIRING/PLAY/PAUSE
Press to play or pause a
Press & hold to begin
pairing a Bluetooth device.
loaded CD.
MEN/CLK SET
Press to set the clock or
save a radio station.
Pres to power the music
Press to switch to CD, LINE
SKIP/SEARCH/TUNE-
Press to skip between tracks
on loaded CD or Bluetooth.
Press and hold to search
through an individual track.
Press to tune the FM radio.
Press to adjust the time
when setting the clock.
STANDBY
system off or on.
SOURCE
IN, Radio or Bluetooth
modes.
MUTE
Press to mute the
volume.
VOLUME
Press to adjust the
volume.
Press to program a loaded
PROGRAM
disc to play tracks in a
specified order.
OPEN/CLOSE
Press to open or close
the CD door.
REPEAT
Press to repeat the
current track or an
entire album/playlist.
SKIP/SEARCH/TUNE+
Press to skip between tracks
on loaded CD or Bluetooth.
Press and hold to search
through an individual track.
Press to tune the FM radio.
Press to adjust the time
when setting the clock.
EQ
Press to switch the preset
EQ to Pop, Jazz, Classic,
Rock or Normal.
MEM(+/-)
Press the cycle through saved
radio stations.
STOP
Press to stop a CD
during play.
5
Setup
Power
Plug the included AC/DC power
adapter into the DC POWER INPUT on
the music system and an AC power
outlet to power the music system.
Battery Power
Requires 1, CR2025, battery (preinstalled).
Clock
CR2025
OPEN
PUSH
3V
CR 2025
LITHIUM BATTERY
CR2025
CR 2025
3V
LITHIUM BATTERY
OPEN
PUSH
Setting the Clock
1. Press the POWER button to turn
the music system o.
2. Press and hold the MEM/CLK SET
button on the music system.
The hour will begin to blink on the
display.
3. Press the SKIP/SEARCH buttons to
adjust the hour.
An “AM” indicator will appear on the
display when the time is set to the
AM. A “PM” indicator will appear on
the display when the time is set to
the PM.
6
Press the MEM/CLK SET button to
4.
set the minute.
The minute will begin to blink on the
display.
5.
Press the SKIP/SEARCH buttons to
adjust the minute.
6.
Press the MEM/CLK SET button to
nish setting the clock
CD
Loading a CD
1. Press the OPEN/CLOSE button
on the top of the music system to
open the CD door.
2. Load a CD into the music system,
label side facing up.
3. Close the CD door.
Playing a CD
1. Follow the instructions for Loading
a CD.
2. Press the POWER button to power
the music system on.
3. Press the SOURCE button to switch
to CD mode. The CD will playing
automatically.
The track number will appear on the
display, to the right of the time, when
the music system is in CD mode.
4. Press the PLAY/PAUSE button to
pause a loaded disc. press again
to resume.
5 Press the STOP button to stop a
loaded disc .
Programming a CD
1. Follow the instructions for Playing
a CD.
2. Press the STOP button.
The loaded disc must be stopped to
create a program.
3. Press the PROG. button on the
front of the music system.
“PROG” and a number, indicating
the order in which the next selected
track will play, will appear on the
display.
4. Press the SKIP/SEARCH buttons to
select a track.
5. Press the PROG. button again
to save the selected track to the
program.
6. Repeat steps 4 and 5 to program
up to 20 tracks to play in the order
they were selected.
Cancelling a Programmed CD
1. After programming the CD, press
the STOP button twice to cancel
the program.
7
FM Radio
Tuning the FM Radio
1. Press the POWER button to power
the music system on.
2. Press the SOURCE button to
switch to FM radio mode.
“FM” will appear on the display.
3. Press the TUNE +/- buttons to tune
the FM radio.
Adjust the position of the FM wire
antenna to improve FM radio
reception.
Saving an FM Radio Station
1. Follow the instructions for Tuning
the FM Radio.
2. Press the TUNE +/- buttons to tune
the FM radio to the desired station.
3. Press the MEM/CLK SET button on
on the music system or the
MEM/CLK SET button on the
remote.
A preset number (P01) will appear on
the display, indicating which preset
the current station will be saved to.
4. Press the MEM +/- buttons to
adjust the preset number (P01 P20).
5. Once the desired preset is selected,
press the MEM/CLK SET button on
the music system or the MEM/CLK SET
button on the remote to save the
current FM radio station to the
selected preset.
Playing a Saved Radio Station
1. Follow the instructions for Tuning
the FM Radio and Saving an FM
Radio Station.
2. Press the MEM± buttons to
cycle through saved radio stations.
8
Bluetooth
Pairing a Bluetooth Device for the first time
1. Press the POWER button to power
the music system on.
Press the SOURCE button to
2.
switch to Bluetooth mode.
“ ” will appear on the display and blanking.
Press and hold the PAIRING/PLAY/PAUSE
3.
button to begin pairing to a Bluetooth
device, “ ” will flash quickly.
Using the native controls on your Bluetooth
4.
device, select the SRCD2731BT in your
Bluetooth settings to pair. If your device
requests a password, enter the default
password "0000".
Refer to the user's manual for your specific
device for instructions on pairing and
connecting Bluetooth devices.
5.
When successfully paired and connected, a
beep will issue from the unit and the " "
will display a solid light.
After initial pairing, the unit will stay paired
unless unpaired manually by the user or
erased due to a reset of the device. If your
device should become unpaired or your find it
is unable to connect, repeat the above steps.
Playing Audio Wirelessly
After pairing to a Bluetooth device,
1.
use the native controls on the con-
nected Bluetooth device to select a
track.
Play, pause or skip a selected track
2.
using the native controls on the
connected Bluetooth device or the
controls on the unit machine.
3.
Audio played trough the
connected Bluetooth device will
now be heard through the
speakers.
9
Line in
Using the 3.5mm Audio Input
Requires a 3.5mm audio cable (not
included).
1. Connect a 3.5mm audio cable to
the LINE IN jack on the music
system and the headphone
jack or 3.5mm audio output on an
MP3 player or other audio source.
2. Press the POWER button to power
on the music system.
3. Press the SOURCE button to
switch to LINE IN mode.
4. Use the native controls on the
connected MP3 player or other
audio source to control the music
played through the music system.
10
Using Headphones (not included)
If you would like to listen to your music
privately through the use of
headphones, you may do so in one step.
Simply plug your eadphones into the
phones jack, located on front the unit.
Compatible headphones have a 3.5mm
diameter stereo plug and an impedance
of 8-32 Ohms. When your headphones
are connected, the stereo speakers are
automatically disconnected.
Specification
ower Adaptor:
P
Bluetooth:
Frequency Range: FM 87.5 – 108 MHz
Power output:
Dimensions:
Weight:
AC input 120V~ 60Hz
DC Output 10.5V 1.5A
Bluetooth Specification version 2.1
Support profile A2DP
5W (RMS) x2
32 cm (H) x
?? Kg.
72 cm (W) x 21 cm (D)
11
Loading...