Modern TR1003 User Manual
INSTALLATION & OPERATING INSTRUCTIONS
(Model:TR1003)
IF YOU CANNOT READ OR UNDERSTAND THESE INSTALLATION INSTRUCTIONS, DO NOT ATTEMPT TO INSTALL OR OPERATE.
INTRODUCTION
This Durablow remote control systemis toprovide a safeand reliableremote control systemforgas heating appliances, such
as fire fire place.Th e systemcan be operated thermostatically or manually from the transmitter (remote handset).The
systemoperates on radio frequencies (RF) within a 20-foot range using non-directional signals.The remote receiver box
code mustbe matched tothe transmitter prior toinitial use(see LEARNING TRANSMITTER TO RECEIVER
ReadALL sections and original manufacturer manual for safety installation before any action. These safety features shut
down the system and appliance, such as fireplace when a potentially unsafe condition exists, such as high-heat.
Contents:
1 PACKING LIST
2 LCD DISPLAY ICONS
3 BASIC TRANSMITTER FUNCTIONS& MODES
4 SETTING UP THE TRANSMITTER
........................................................ 2
........................................................ 2
........................................................ 2
........................................................ 3
).
Page
5 SETTING THE CLOCK
6 CONVERTING ºF / ºC SCALE
7 REMOTE RECEIVER BOX
8 WARNING &REMINDER
9 PREINSTALLATION
10 WALL MOUNTING
11 HEARTH MOUNT
12 WIRING INSTRUCTIONS
13 LEARNING TRANSMITTER TO RECEIVER
14 SYSTEM TESTS & CHECK LIST
15 ADDITIONAL INFORMATION
16 TROUBLE SHOOTING
17 WARRANTY & LEGAL DISCLAIMER
........................................................ 3
........................................................ 3
........................................................ 4
........................................................ 4
........................................................ 5
........................................................ 5
........................................................ 5
........................................................ 6
........................................................ 7
........................................................ 7
........................................................ 8
........................................................ 10
........................................................ 11
Version1.0(2016)Page
1
18 FCC / ID
........................................................ 11
PACKING LIST:
Please check and make sure all parts are in good condition before installation. Any questions, please do NOT return to
dealer, but email us (info@payandpack.com)
1. Remote transmitter (1), Remote receiver box w/ 18” wire (1)
2. Wall mount cover plate (1), Switch box screw (2), Slide switch button (1)
3. 1.5V Batteries: AA-size (4), AAA-size (2)
4. Installation Instructions (1)
immediately, we will do our best to assist you. Thank you.
Fig. 1 Transmitter Fig. 2 LCD display on transmitter
LCD DISPLAY I CONS (Fig. 2)
1.LOW BATTERY - Once it appears which means battery power is low.Replace batteries in 2 weeks.
2.TIMER
3.MODE – Indicates system operation modes.ON means the systemis manually ON.OFFmeans the entiresystemis
4.SET– Indicates desiredsetroom temperature ofTHERMO
5.FLAME– Indicates burner/valve is at ON position.
6.CLOCK – Indicates the current time.
7.ROOM– Indicates CURRENTroom temperature.
8.°F / °C– Indicates degrees in Fahrenheit or Celsius (convertible).
*1
– Indicates time remaining before systemshuts OFF.Maximum 9-hour setting for timer programming.
OFF.THERMO
*2
means the systemwill automatically cycle ON/OFF,with the desired set temperature.
*2
mode. (works with ROOM)
BASICTRANSMITTERFUNCTIONS& MODES
NOTE: For model TR1002-T, the THERMO mode is NOT included; For TR1002-TH, the TIMER mode isNOT included.
IMPORTANT:The transmitter requires twoAAA-size 1.5V batteries (included).New (fully charged) batteries arerequired for
proper functionality ofthe system.Insertbatteries into the transmitterbattery compartment on the back,positioning the (+) and
(-) ends ofthe batteries as indicated on the casing. (Fig. 1)When the batteries are inserted properly, LCD will display initial
numbers.
Version1.0(2016)Page
2
g
e
CAUTION: Due tothe temperature-monitoring components in the transmitter,it isimportant to allow the transmitter todetect
theroom temperature before accurately displaying room temperaturesonthe screen. Normally it takes 5 to 15 minutes
forevery first time placing this transmitter in a new location / environment.
Tobegin the mode cycle (Fig. 3),press and release the MODE button (Fig. 1) until the LCD screen reads OFF (Fig. 4).
Step1:Press the MODE button one time tomanually turn ON the appliance (Fig. 5).Timer
The receiver will make sounds of quick BEEP X 2 (♫, ♫).
Step2: Press the MODE button a second time toput the toput the systemin THERMO
*1
Timer
★NOTE: The Thermostat
turn ON again when the room temperature go below desired set temperature, at the meantime, Timer
However, once the set time ends, the Timer
and Thermostat*2 are both available in this mode.
*2
has first priority to turn OFF when the room temperature reach desired set temperature& it will
*1
will turn OFF the entire system and go back to OFF mode (Fig. 4).
*1
is available in this mode.
*2
mode (Fig. 6).
*1
keeps countdown.
Step3: Press the MODE button a third time toturn the appliance back OFFagain as show in (Fig. 4).
sounds of continuous BEEP for one second (♫~~).
The receiver will make
Fig. 6 Thermo*2mode
Fi
*3
. 3
Mode sticker Fig. 4 OFF mode Fig. 5 ON mod
Fig. 7
SETTINGUPTHETRANSMITTER
Any blinking numbers on the LCD screen indicate the systemis awaiting user’s input. Using the “＋”and “－” buttons (Fig. 7)
to increase or decrease the numbers, and press “OK” button to set / confirm. If no change / action is made within 15-seconds,
the system will accept the numbers and finish the
procedure.
SETTINGTHE CLOCK (Fig.7)
1.Press and hold theTIMERbutton on the transmitter for three seconds.The hour digit(s) will become blinking.
2.Press the “＋”and “－” button to set.
3.Aftersetting the desired hour,press and release theTIMER
5.Press and hold theTIMER
button again for three seconds to finish setting. You can also press the OKbutton to finish setting.
button again tosetthe minutes.
CONVERTING ºF/ºC SCALE
Version1.0(2016)Page
3
The default setting for temperature is ºF.To change the setting from ºFto ºC (or ºC to ºF), first press and hold the “＋”and
“－” buttons on the transmitter simultaneously(Fig. 7).The highest settemperature is 99º Fahrenheit = 32º Celsius.
Explanatory notes for TIMER, THERMO, Thermostat, & Modes:
*1: TIMER mode is NOT available / included in model TR1002-TH.
*2: THERMO mode & Thermostatare NOT available / included in modelTR1002-T
*3: Mode sticker, located under the flip cover of transmitter, varies with different models.
REMOTERECEIVER BOX
The remote receiver box requiresfourAA-size 1.5V batteries (Fig. 8). When LOW battery icon appears on the screen, please
replace batteries.
The remote receiver box equips the microprocessor that receives thesignals / commands from the transmitter in order
tocontrol systemoperations / functions. Itmakes sounds of quick BEEP X 2 (♫, ♫)
andmakes sounds of continuous BEEP for one second (♫~~)
ends automatically).But no beep when cycling ON/OFF
automatically inTHERMO*2 mode.
when it receives an OFF command manually (or when Timer
The remote receiver box has a 3-position slide switch (ON/REMOTE/OFF) and a LEARN button on the front panel (Fig. 8).
when it receives an ON command,
Fig. 8 Fig. 9
ON mode: Slide the switch to the ON position (toward the LEARN button), the system will remain ON all the time. Remote
transmitter is disabled
.
REMOTE mode: Slide the switch to the REMOTE position (middle), the system will ONLY operate with receiving commands
from the remote transmitter.
OFF mode: Slide the switch to the OFF position, the system will remain OFF all the time. Remote transmitter and Receiver
box are both disabled
★NOTE: The OFF mode
.
is strongly recommended if house is unattended for a long time. For safety, placing the slide switch
in the OFF position also functions as a safety “LOCK-OUT” by both turning the system off and disable the remote receiver.
W
ARNING& REMINDER
ThissystemMUST be installed exactly as complied with these instructions.Read all instructions before installation,
Version1.0(2016)Page
4
Loading...