Page 1
Backboard Upper
Metal rod
Highchair Leg
Footboard
Seat board
Tray
Safety strap
Support brace
IMPORTANT!
KEEP FOR FUTURE REFERENCE:
WARNING: Never leave your child unattended in the highchair. Strict
adult supervision is required at all times.
WARNING: Ensure the safety strap is in use at all times to avoid the child
slipping downwards and causing injury. We recommend the use of the
shoulder and waist harness at all times to avoid injury caused by falls.
WARNING: Do not use the highchair unless components are correctly
fitted and adjusted.
WARNING: Ensure the highchair is positioned away from objects or
structures that can cause injury. Be aware of the risk of open fire and
other sources of strong heat, such as electric bar fires, gas fires etc, in
the vicinity of the highchair.
WARNING: Ensure both the seat and footrest are locked into positon
and cannot be moved by hand, before placing the child in the highchair.
Do not tighten all screws until all components have been assembled.
The highchair should not be used until the child can sit up unaided.
Do not use the highchair if any part is broken, torn or missing.
Only use the highchair on a flat, even and horizontal floor.
Do not elevate the highchair on any structure or table.
WARNING: For babies/toddlers under 2 years old, please ensure the
seat is positioned on the 1st or 2nd level from the top ONLY.
Original Highchair
1
mocka.co.nz | mocka.com.au
Assembly Instructions
Thank you for your purchase.
Please follow the instructions below for correct assembly.
Page 2
x6
B
A
x4
C
D
E
F
G
H
x6
x1
x2
x2
x4
x1
screw
long screw
bolt nut
Allen key
tray screw
tray bolt
footpad
safety strap
I
J
leg
extender
small screw
x2
15 mm
x2
screwdriver required
Hardware Supplied
The best way to clean your highchair – especially the tray is
with a clean damp cloth, and then wipe completely dry.
We recommend you DON’T use household cleaners as these
could lift the varnish and upset the wood finish.
Using a damp cloth and wiping dry will ensure longevity of
your highchair.
.
To alter the seat and footrest heights after assembly, simply
loosen all the screws in the upper and lower backrests and
the metal rods on both sides of the highchair. Once loosened
this will allow the seat and footrest to be pulled out. Insert into
the new positions and then lock in place by re-tightening all
the screws. Ensure both the seat and footrest are locked into
position and cannot be moved by hand, before placing the
child in the highchair
Thank you!
The Mocka Team
Pre-installed Hardware
Original Highchair
2
mocka.co.nz | mocka.com.au
Assembly Instructions
Page 3
1
x2
C
A
A
A
A
B
B
C
C
x2
B
To begin assembly, line up backboards, metal rods, and
support brace between both legs of the highchair.
Ensure all components slot into the corresponding
grooves on the inside of the legs. Loosely fasten rods
to the highchair legs using screws (A) and allen key
provided. Attach wooden support brace using long
screws (B) and bolt nuts (C) as shown.
Original Highchair
3
mocka.co.nz | mocka.com.au
Assembly Instructions
Page 4
2
3
Slide seat board and foot board into slots in the highchair legs
at appropriate heights as required for chid comfort.
For babies we recommend the seat on the rst or second level down.
Loosely fasten upper and lower backboards to legs
using long screws (B) and bolt nuts (C). Hold nut using a
screwdriver to ensure it is in the right position for screws
x4
x4
B
B
C
C
B
C
Note: It is important to ensure that the
foot board is inserted at least three rungs
below the top metal rod.
Original Highchair
Assembly Instructions
4
mocka.co.nz | mocka.com.au
Page 5
Jolt Wardrobe
ASSEMBLY INSTRUCTIONS
5
mocka.co.nz | mocka.com.au
4
5
From the back of the chair, fasten the tray through the
legs using the tray screws (E) and tray bolts (F) on each
side. Tighten screws using the allen key provided.
Remove any screws already in the ends of the tray, and
then slide tray onto highchair leg supports. Make sure
one set of holes in the tray line up with holes in the legs.
E
E
F
F
x2
E
Original Highchair
Assembly Instructions
5
mocka.co.nz | mocka.com.au
Page 6
6
7
IMPORTANT - To ensure the highchair is 100% safe for your child
please read this important information. Start by working in a
methodical manner by tightening the bottom left screw, then
tightening the bottom right screw. Continue in this manner,
alternating from left to right, working your way up to the top of the
Highchair. This will ensure the pieces lock into place and have the
correct tension and the highchair is balanced. Attach the padded
cushions to seat and backboard for added comfort. Enjoy!
Thread safety strap through the groove in the seatboard and
through the underside of the tray as shown. Pull the strap
tight and fold over the velcro flaps onto the strap to secure
it in place.
x1
Original Highchair
Assembly Instructions
6
mocka.co.nz | mocka.com.au
Page 7
8
9
Attach leg extender at the desired point using a
15mm small screw (J) & screwdriver. All done!
To attach the leg extenders, remove white
plastic footpad.
LEG EXTENDERS
I
G
I
G
x2
J
Original Highchair
Assembly Instructions
7
mocka.co.nz | mocka.com.au
Page 8
10
11
Connect the rest of the harness to the anchor-straps
eht peeK .nwohs sa selkcub htob rehtegot gnippilc yb
harness and middle buckle loose and open for now.
Separate the anchor straps and loop around the high-chair
supports and under the backrest. Tie to high-chair frame
by passing each clip through the loop in the straps.
x2
x2
Highchair Harness
Assembly Instructions
8
mocka.co.nz | mocka.com.au
Page 9
12
13
shoulders and chest. To take the child out of the chair,
simply unclip the buckle and slip o harness.
All done! Enjoy!
A. Carefully sit child in the highchair and slip arm through harness.
B. Slip child’s second arm through the harness loop.
C. With the harness sitting over the shoulders, clip the front buckles
together as shown.
B
C
A
Highchair Harness
Assembly Instructions
9
mocka.co.nz | mocka.com.au
Loading...