ASSEMBLY INSTRUCTIONS
Thank you for your purchase.
Please follow the instructions below for correct assembly.
Jolt Bedside
mocka.co.nz | mocka.com.au
1
Hardware Supplied
x4
B
A
x10
C
D
G
H I
x4
x8
x10
x18
x20
12 mm
L + R
L + R
bolt
locking nut
dowel
long screw
small screw
30 mm
FE
x8
x8
small bolt
small
locking nut
x14
small nail
x4
plastic glides
J K
Please clear any loose wood from the locking nut holes before inserting the nut to ensure it locks 100%
x2
washer
Z
Wall
Screw
r/washer
screw
x1
Y
wall
anchor
x1
X
Safety
Strap
W
Wall Strap
V
WARNING: Any furniture that is not anchored to a wall has
the potential to tip over in certain circumstances, i.e. if a
child attempts to climb up on the furniture or in the event of
an earthquake. Accordingly, we recommend that all
furniture is anchored to a wall. We supply a free safety wall
anchor with all furniture sold and we recommend these are
used to prevent your product tipping. The fixing device
provided should fit most wall types, but please note that
different wall materials may require different fixing devices
from those supplied.
Phillips & Flathead screwdriver and hammer required
ASSEMBLY INSTRUCTIONS
Jolt Bedside
mocka.co.nz | mocka.com.au
2
1 2
Screw in bolts (A) and insert dowels (C) into holes in panels [2]
and [3]. Slot together with parts [4], [5] and [6]. Place 8x locking
nuts (B) into holes in [5] and [6]. Tighten with a screwdriver.
To begin assembly attach 2x slide rails (H) in place on each
of the panels [2] and [3] as shown using 2x small screws (G)
in each rail bracket. Fasten all screws with a screwdriver.
2
H
G
G
H
G
G
G
H
3
G
G
H
G
A
C
B
C
C
C
B
A
C
B
C
C
A
C
B
C
B
A
C
B
B
B
2
3
6
6
5
4
4
C
C
B
x6
C
x6
A
x8
G
ASSEMBLY INSTRUCTIONS
Jolt Bedside
mocka.co.nz | mocka.com.au
3
3
4
Insert 4x bolts (A) and 4x dowels (C) into top panel [1].
Slot together with the rest of the cabinet. Place 4x locking
nuts (B) into holes in the side panels and tighten with
screwdriver. Hammer 4x plastic glides (J) into the base.
Connect back panels [7] together with connector stick
[13]. Attach both panels to the cabinet using 14x nails (K)
and a hammer.
A
C
A
C
B
C
A
C
B
1
x4
C
A
x4
B
J
J
J
13
K
K
K
K
K
K
K
K
K
7
7
ASSEMBLY INSTRUCTIONS
Jolt Bedside
mocka.co.nz | mocka.com.au
4
5
6
Drawers (x2) Drawers (x2)
Assemble the drawers by screwing 4x bolts (E) into the front panel
[8]. Attach to side panels [9] and [10] using 4x locking nuts (F).
Slide the base panel [11] into place in the grooves in
side and front panels.
F
E
F
E
E
E
F
11
8
10
F
x4
9
ASSEMBLY INSTRUCTIONS
Jolt Bedside
mocka.co.nz | mocka.com.au
5
7 8
Flip drawer over and attach 2x rail components (I) to both
left and right underside of the drawer using 4x screws (G).
Repeat Steps 5 to 8 to assemble the second drawer.
Drawers (x2) Drawers (x2)
Fasten back panel [12] into place using 4x long screws (D)
in the holes in the side panels.
12
D
D
D
D
G
G
G
G
Jolt Bedside
ASSEMBLY INSTRUCTIONS
mocka.co.nz | mocka.com.au
6
9 10
Ensure all drawers easily slide open and
closed.
Slide all three completed drawers into
place on the rails in the cabinet unit as shown.
11
12
Attach safety strap (V) to the top of the back side of the unit
using screw (Y) and washer (Z). Tighten with a screwdriver. Once
assembled lift furniture into place, do not drag.
Move the unit into the desired location up against a wall. Use a drill to
create a small hole lining up with the top of the safety strap (V). Fasten
to wall using wall anchor (X), washer (Z) and screw (W). Ensure unit is
balanced and steady before use. You’re done, enjoy!
7
mocka.co.nz | mocka.com.au
Jolt Bedside
ASSEMBLY INSTRUCTIONS
Wall Strap
Y
V
x1
r/washer
screw
V
x1
wall
anchor
wall
screw
Washer
Strap
V
X
Z
W
Z
Loading...