WARNING: Any furniture that is not anchored to a wall has the potential
to tip over in certain circumstances, i.e. if a child attempts to climb up on
the furniture or in the event of an earthquake. Accordingly, we
recommend that all furniture is anchored to a wall. We supply a free
safety wall anchor with all furniture sold and we recommend these are
used to prevent your product tipping. The fixing device provided should
fit most wall types, but please note that different wall materials may
require different fixing devices from those supplied.
x4
B
A
x20
C
D
E
F G
H
x4
x28
x28
x40
x22
x8
12 mm
30 mm
12 mm
L + R
L + R
Hardware Supplied
x1
washer
Z
Wall
Screw
r/washer
screw
x1
Y
wall
anchor
x1
X
Safety
Strap
W
Wall Strap
*We recommend using a Flathead screwdriver to tighten all locking nuts 100% before first use.
Phillips & Flathead screwdrivers required
Brooklyn Change Table & Drawer Set
1
mocka.co.nz | mocka.com.au
Assembly Instructions
Thank you for your purchase.
Please follow the instructions below for correct assembly.
1
2
Begin by identifying each wooden piece using the number labels on their
side. Lay them all out in order. Screw hardware (D) into holes in pieces
[1] and [2]. Slot together with table pieces [3] as shown. Place locking
nuts (E) into corresponding holes and tighten with a screwdriver.
Screw hardware (D) into the pre-drilled holes in piece [3]. Push or tap in
two wooden dowels (F) into piece [3] as shown.
3
1
2
D
D
D
x2
x4
E
D
x4
E
E
D
F
F
D
D
D
E
Brooklyn Change Table & Drawer Set
2
mocka.co.nz | mocka.com.au
Assembly Instructions
3
4
Flip table top over and slot into piece [6]. Screw in two bolts (D) and two
dowels (F) into shelf piece [7]. Push nut (E) into holes in piece [6] as
shown and tighten with a screwdriver.
Find pieces [4] and [5]. Line up two drawer rails (B) with corresponding
holes on each wooden piece as shown above. Fasten to wood using
three screws (A) in each.
6
7
4
5
B
B
A
A
E
F
D
E
x4
D
x2
B
B
x4
A
A
A
E
E
Brooklyn Change Table & Drawer Set
3
mocka.co.nz | mocka.com.au
Assembly Instructions
5
6
Screw bolts (D) and dowels (F) into side panels [4] and [5] as shown.
Slot (D) and (F) into each end of pieces [8] and [9]. Slide table and shelf
piece, and braces [8] & [9] together between side panels. Secure by
placing hardware (E) in corresponding holes in the underside of pieces
[3, 7, 8, & 9]. Tighten until rigid.
On the back side of the set, fit boards [10] and [11] into the grooves. Use
small screws (G) all around to fasten boards to the change table unit.
4
5
8
9
Fx2
x12
E
D
x12
E
E
F
F
D
E
E
D
F
F
D
F
D
F
D
D
Fx2
E
E
E
10
11
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
G
Brooklyn Change Table & Drawer Set
Assembly Instructions
4
mocka.co.nz | mocka.com.au
Jolt Wardrobe
ASSEMBLY INSTRUCTIONS
5
mocka.co.nz | mocka.com.au
7
8
To assemble the drawers, first screw 4x bolts (D) into front panel [15].
Fit panels [12] and [13] over the bolts as shown, ensuring the grooves
in panels face inwards. Secure using 4x locking nuts (E) and tighten
with a screwdriver.
Slot panel [16] down into grooves in the side and front panels. Insert 2x
dowels (F) into the end of both support braces [17] and peg into holes in
front panel [15].
13
12
15
16
17
17
Fx2
Fx2
E
E
E
D
D
D
D
D
x4
E
x4
Drawers (x2) Drawers (x2)
Brooklyn Change Table & Drawer Set
Assembly Instructions
5
mocka.co.nz | mocka.com.au
9
10
Insert 2x dowels (F) into the other end of each support piece [17]. Place
back panel [14] into position on dowels and fasten into place using 4x
screws (H).
Finally, attach rail hardware (C) to both left and right side of the drawer
using screws (A). Repeat Steps 7 to 10 until all four drawers are fully
assembled.
Drawers (x2) Drawers (x2)
H
14
H
H
H
Fx2
Fx2
x4
H
A
C
A
A
Brooklyn Change Table & Drawer Set
Assembly Instructions
6
mocka.co.nz | mocka.com.au
11
12
Now both drawers are made up, slide them into rails in the change
table unit.
Ensure the drawers easily slide open and closed.
x2
Brooklyn Change Table & Drawer Set
Assembly Instructions
7
mocka.co.nz | mocka.com.au
13
14
Attach the safety strap (W) to the top of the back side of the unit using
screw (Y). Tighten with a screwdriver.
Once assembled lift furniture into place, do not drag. Use a drill to create
a small hole lining up with the top of the safety strap (W). Fasten to wall
using wall anchor (X), washer (Z) and screw. Ensure the unit is balaced
and steady before use. You’re done, enjoy!
Y
Y
W
W
x1
X
Z
x1
wall
screw
wall
anchor
wall
screw
Washer
Strap
Brooklyn Change Table & Drawer Set
Assembly Instructions
8
mocka.co.nz | mocka.com.au
Loading...