Blake Console Table
Assembly Instructions
Thank you for your purchase.
Please follow the instructions below for correct assembly.
A B
dowel
x12
H
wheel
x4
WARNING: Any furniture that is not anchored to a wall has the potential to tip over in certain
circumstances, i.e. if a child attempts to climb up on the furniture or in the event of an earthquake.
Accordingly, we recommend that all furniture is anchored to a wall. We supply a free safety wall anchor
with all furniture sold and we recommend these are used to prevent your product tipping. The fixing device
provided should fit most wall types, but please note that different wall materials may require different fixing
devices from those supplied.
washer
x8
I
wedge
x4
C D E F G
bolt
x6
J
screw
x4
Hardware Supplied
locking
nut x6
felt pad
x4
K
small
screw
x32
L
spring
washer
x8
allen
key
x1
M
bolt
x8
wheel
x4
N
screw
x6
safety
strap x1
WV
screw
x1
X
wall
anchor
x1
Wall Strap
Y
wall
screw
x1
Z
washer
x2
Phillips & Flathead screwdrivers required.
For quicker assembly, we recommend the
use of a power drill on a low-speed setting.
mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore BC, QLD, 4558
1
Blake Console Table
Assembly Instructions
1
2
E
C
A
1
7
E
H
E
H
G
8
E
G
Insert 6x dowels (A) and 6x bolts (C) into panel [1].
Tighten with a screwdriver.
mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore BC, QLD, 4558
Attach 2x wheels (G) and (H) to each panel [7] and [8] as shown,
and secure with 32x small screws (E). Tighten with a screwdriver.
2
Blake Console Table
Assembly Instructions
3 4
2
D
6
2
5
3
Attach panels [2] , [3] and [5] to panel [1] and secure with
6x locking nuts (D). Tighten with a screwdriver.
mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore BC, QLD, 4558
D
D
D
1
5
3
Slide panel [6] between the grooves of panels [2] ,[3] ,[5] and [1] to
form the back of the unit, as shown.
1
3
Blake Console Table
Assembly Instructions
5 6
B
L
M
K
9
F
4
2
N
5
A
3
Insert 6x dowels (A) into the ends of panels [2], [3] and [5].
Attach panel [4] to the unit and secure with 6x screws (N).
Tighten with a screwdriver.
mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore BC, QLD, 4558
B
L
M
4
Attach 4x legs [9] to panel [4] with 8x washers (B), 8x spring washers (L)
and 8x bolts (M). Tighten with an Allen key (F). Apply 4x felt pads (K) to
legs [9] as shown.
4
Blake Console Table
Assembly Instructions
7 8
I
1
8
7
Note: If the door is not sliding smoothly or
sitting straight, there is a screw in the
middle of the wheel on the bottom of each
door that can be tightened/loosened until
the door is sitting properly.
back
OK
J
1
V
Z
W
V
Z
W
I
J
6
Attach door panels [7] and [8] as shown, starting with the back door
first and then the front door. Press the clip down on the back of the
door to assemble the door. Push the clip back up to lock into place.
mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore BC, QLD, 4558
Attach 4x wedges (I) into the corners of the back of the unit and secure
with 4x screws (J). Attach 1x safety strap (V) to the top of the back side
of the unit as shown using 1x washer (Z) and 1x screw (W). Tighten
with a screwdriver.
5
Blake Console Table
Assembly Instructions
9
X
Z
Y
X
Z
Y
Once assembled lift furniture into place, do not drag. Use a drill to create
a small hole lining up with the top of the safety strap (V). Fasten to the
wall using 1x washer (Z), 1x wall anchor (X) and 1x wall screw (Y).
Ensure unit is balanced and steady before use. You’re done, enjoy!
mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore BC, QLD, 4558
6
Loading...