Mobotix Mx-S16A-S3, Mx-S16A-S2, Mx-S16A-S1 User Manual
Sensor Modules
1.1
Sensor module
Sensor module
Rear
Sensor module
SMA-B-6D/N/LCS
SMA-TS-T079–237
SMA-B-6D/N/L016–500
SMA-TP-T079–237
1
2
3
4
5
Sensor module
Thermal(-TR)
PTMount
Thermal(-TR)
S16
• Mx6 system platform, H.264 support
• Recording on internal microSD card (SDXC, SDHC installed)
• Various installation options for ceilings or walls
• Max. length of the sensor module cable is 3 m/3.3 yd each
• Microphones integrated in SMA-S and SMA-B sensor modules
• Audio connectors for microphone and speaker integrated
• Sensor for temperature and shock detector(*) integrated
• Weatherproof and sturdy camera housing (IP66, IK06)
Quick Install
S16 DualFlex
Modular 6MP Dual Camera with Day/
Night and Thermal Sensor Modules
for Concealed Installation
MOBOTIX 6MP camera for concealed installation in indoor
and outdoor applications, available as S15D DualFlex
with external sensor modules SMA-S-6D/N/L016 to 500
and cables up to 3 m/3.3 yd long with Day/Night or NightLPF image sensors. Can be combined with one or two
Thermal(-TR) image sensors SMA-TP-T079/119/237 for
thermal imaging and temperature measurement even in
complete darkness.
*: with rmware version 5.0.1 and higher
S16 Standard Delivery
M.10
M.9
M.8
M.7
M.6
M.5
M.4
M.3
M.2
M.1
Item Count Part Name
1.1 1 S15D Core (base module with base plate)
1.2 1 Housing cover for S15D (installed)
1.11
Standard Delivery
1.10
1.6
1.4
1.9
1.2
1.8
1.3
1.5
More information:
www.mobotix.com > Products > Outdoor Cameras > S16
Mx-S16
32.836-004_EN_10/2017
Standard Delivery
Item Count Part Name
1.3 1 Stainless steel Allen screw with at head M4x8 mm (installed)
1.4 1 Sealing ring (installed)
1.5 3 Sealing plug blue, small (sensor modules, USB, mounted)
1.6 1 Sealing plug blue, large (Ethernet patch cable, mounted)
1.7 1 Cable lock with bayonet catch (Ethernet patch cable, mounted)
1.8 1 Single-wire plug, white (Ethernet installation cable, microphone,
1.9 1 MicroSD card pre-installed (SDHC)
1.10 1 Threaded plug for SD card, blue (mounted)
1.11 1 Ethernet patch cable, 50 cm/19.7 in with sealing
1.7
Item Count Part Name
M.1 4 Stainless steel washers dia. 4.3 mm
M.2 4 Dowels 6 mm
M.3 4 Stainless steel wood screws with hex head 4x40 mm
M.4 2 Cable plug 5 to 7 mm, white (Ethernet installation cable)
M.5 1 Cable plug 3 to 5 mm, white (Ethernet installation cable)
M.6 1 Allen wrench 2.5 mm
M.7 1 Lens wrench (lens, dome)
M.8 1 Module wrench (sensor module, glass cover/lter insert)
M.9 1 Cable tie (Ethernet installation cable, microphone, speaker)
M.10 1 Screwdriver (terminals)
speaker, installed)
Mounting Supplies
Sensor Modules of the S16 (to Be Ordered Separately)
SMA-S-6D/N/L016
Dome
Plastic nut
BlockFlexMount
SMA-S-6D/N/L036–237
Protective
glass insert
Plastic nut
BlockFlexMount CS-Mount (without lens)
Installing the Sensor Modules
Lens cover
SMA-S-6D/N/L500
PTMount Thermal(-TR)
(all except Thermal)
Sensor module cable
Top (markings)
Sensor module Thermal(-TR)
1. Mounting to a Wall or Ceiling (SMA-S-6D/N/L016 to 500)
Remove the plastic nut from the sensor module 1. Remove the bayonet
catch and the rubber plug 2.
Insert the module into the hole you just drilled (43 mm) 3.
Tighten the plastic nut to keep the sensor module safely in place 4.
Push the sensor module cable plug into the connector at the back of the
module housing 5.
2. Installing a Sensor Module Thermal(-TR)
For information on installing and the technical specications, please refer
to the separate documentation
«Quick Install Sensor Module Thermal(-TR)»
which is part of that product delivery.
,
3. Installing a PTMount-Thermal(-TR)
For information on installing and the technical specications, please refer to
the separate documentation
«Quick Install PTMount-Thermal(-TR)»
, which
is part of that product delivery.
Mounting the Camera
Installation Using the Base Plate
Attach the camera using the supplied or other screws by aixing the base
plate to a suitable material 1 (see
page 2
).
«Dimensions/Drilling Template» on
Connections and Initial Operation of the S16
You can nd detailed information on the installation and connections of the S16 in the
Support > Manuals).
Please note that the boot options of this camera have changed compared to its predecessor (see
only has one key ("L"). Regarding the rest of the initial operation of the S16, please see the
LEDs
S15 Camera Manual
«Boot Options of the» on page 2
S15 Camera Manual
(PDF, available on www.mobotix.com >
) and the camera
in
Chapter 3, «Initial Operation»
.
L
Key L
Housing cover
Microphone
Speaker
MOBOTIX patch cable or
additional cable
Ethernet patch
cable
USB
Cam1 Cam2
Base plate
Ethernet installation cable,
LSA terminal block
Additional cable or net-
work installation cable
Conguring the Installed Image Sensors
Open Admin Menu > Hardware Conguration > Image Sensor Conguration and set the image sensors that are installed as le and right image
sensors. If you are using
hemispherical sensor modules with Vandalism domes
, you should open Admin Menu > Hardware Conguration > Lens
Conguration and activate the corresponding option.
Cam1 Cam2MiniUSB
Inserting/Exchanging the SD Card
All camera models can use the integrated microSD card (SDHC) to record video data. In order to exchange the microSD
card, please proceed as outlined in the following instruction. For information on reliable SD cards, please see the
MOBOTIX website www.mobotix.com > Support > MxMedia Library > Planning in the document
Whitelist for MOBOTIX Cameras
When replacing the SD card, make sure that recording has been deactivated in the browser (
Storage on External File Server / Flash Device
1. Remove the SD card
Loosen the threaded plug at the top of the
housing (using a suitable coin, for example)
and remove the plug. Using tweezers, gently
press the SD card into the slot (as indicated by
the arrow) until you hear a
click
protruding slightly and can be easily removed
with the tweezers.
.
. The card is
; activate recording again in the same dialog).
2. Insert the SD card
Again using tweezers, insert the SD card as
shown (contacts facing forward) into the card
Click!
slot. Make sure that you hear a
pushing the card into the slot. The card is now
locked and can be used. Insert the threaded
plug again and tighten it using the coin.
MicroSD Card
Admin Menu > Storage >
click
again when
Click!
Boot Options of the S16
www.mobotix.com > Support > Manuals > IP Camera Systems > DualFlex S16
By default, the camera starts as DHCP client and automatically tries to get
an IP address from a DHCP server. To start the camera in a mode dierent
from the default mode, you can activate the boot menu of the camera.
1. Preparing the Camera
• Disconnect the camera's power supply.
• Reconnect the power supply of the camera.
2. Activating the Boot Menu
The red LED lights up 5 to 10 seconds aer establishing
the power supply and will stay on for 10 seconds. Briey
L
press the key L indicated by the red circle in the gure.
The camera enters the boot menu, ready for selecting
one of the boot options.
The LED now ashes once and repeats the ash signal
aer pausing for one second (the number of ashes indicates the current
boot option). To go to the next boot option, briey press the key again
(< 1 sec). Aer the last boot option, the camera returns to the rst option
(LED ashes once).
LED
ashes
1 x Not used Not available on this camera model. —
2 x
3 x
4 x
*Only on cameras with audio option and installed speaker.
Boot
Option
Factory
Defaults
Automatic IP
Address
Recovery
System
Meaning
Starts the camera with factory defaults
(factory default IP address, users and
passwords will not be reset).
Starts the camera as DHCP client and
tries to obtain an IP address from a DHCP
server. If a DHCP server cannot be found or
no IP address can be obtained, the camera
starts with its factory default address.
Starts the camera with the recovery system, e.g., in order to recover from a failed
update of the camera soware.
Audio
Conrmation*
Boing
Boing Boing
Alarm Sound
3. Selecting a Boot Option
Press the key longer (> 2 sec) into the hole. The camera conrms the selection by ashing rapidly three times. Aer 20 sec, the camera will conrm
the selection by playing a sound according to the table above.
If nothing is selected, the camera will resume its normal boot process
aer a certain time.
Important Notes
Safety Warnings
Notes on Installing:
• This product must not be used in locations exposed to
the dangers of explosion.
• Make sure that you install this product as outlined in
Chapter 2, «Installation»
A faulty installation can damage the camera!
•
When installing this product, make sure that you are only
using genuine MOBOTIX parts and MOBOTIX connection
cables.
•
Only install this product on suitable, solid materials that
provide for a sturdy installation of the xing elements
used.
Electrical installation: Electrical systems and equipment may
only be installed, modied and maintained by a qualied
electrician or under the direction and supervision of a qualied
electrician in accordance with the applicable electrical guidelines. Make sure to properly set up all electrical connections.
Electrical surges: MOBOTIX cameras are protected against
the eects of small electrical surges by numerous measures.
These measures, however, cannot prevent the camera from
being damaged when stronger electrical surges occur. Special
care should be taken when installing the camera outside of
buildings to ensure proper protection against lightning, since
this also protects the building and the whole network infrastructure.
Never touch the lenses: Due to the high performance of the
S16, the area of the image sensor can get quite hot, especially
when the ambient temperature is also high. This does not
aect the proper functioning of the camera in any way. For
this reason, the product must not be installed within the reach
of persons without domes or protective lens covers mounted
on the sensor modules.
Power o before opening the camera or exchanging sensor
modules: Make sure the power supply to the camera is disconnected before opening the camera housing (e.g., when
exchanging the SD card) or when installing or exchanging
sensor modules.
Network security: MOBOTIX products include all of the necessary conguration options for operation in Ethernet networks in compliance with data protection laws. The operator
is responsible for the data protection concept across the entire
system. The basic settings required to prevent misuse can be
congured in the soware and are password-protected. This
prevents unauthorized parties from accessing these settings.
of the corresponding manual.
Attention – Special Export Laws Apply!
Cameras with thermal image sensors ("thermal cameras") are
subject to the special export regulations of the U.S.A. and the
ITAR (International Traic in Arms Regulation):
•
According to the currently applicable export regulations
of the U.S.A. and the ITAR, cameras with thermal image
sensors or parts thereof must not be exported to countries embargoed by the U.S.A. or the ITAR. At present,
this applies to the following countries: Syria, Iran, Cuba,
North Korea and Sudan. The same export ban applies to
all persons and institutions listed in "The Denied Persons
List" (see www.bis.doc.gov > Policy Guidance > Lists
of Parties of Concern).
•
Under no circumstances must the camera itself or its thermal
image sensors be used in the design, the development
or in the production of nuclear, biological or chemical
weapons or in the weapons themselves.
Legal Notes
Legal aspects of video and sound recording: You must comply
with all data protection regulations for video and sound monitoring when using MOBOTIX products. Depending on national
laws and the installation location of the S16, the recording of
video and sound data may be subject to special documentation
or it may be prohibited. All users of MOBOTIX products are
therefore required to familiarize themselves with all applicable
regulations and to comply with these laws. MOBOTIX AG is not
liable for any illegal use of its products.
Disposal
Electrical and electronic products contain many valuable
materials. For this reason, we recommend that you dispose
of MOBOTIX products at the end of their service life in accordance with all legal requirements and regulations (or deposit
these products at a municipal collection center). MOBOTIX
products must not be disposed of in household waste! If the
product contains a battery, please dispose of the battery sep-
arately (the corresponding product manuals contain specic
directions if the product contains a battery).
Disclaimer
MOBOTIX AG does not assume any responsibility for damages,
which are the result of improper use or failure to comply to the
manuals or the applicable rules and regulations. Our General
Terms and Conditions apply. You can download the current
version of the General Terms and Conditions from our website at www.mobotix.com by clicking on the COS link at the
bottom of every page.
§
§
§
Technical Specications S16
Model Versions
Lens Options Mx Sensor
Module
Lens Options
Thermal Image Sensor
Sensitivity
Mx Sensor Module
Sensitivity
Thermal Image Sensor
Image Sensor
Mx Sensor Module
Image Sensor
Thermal Image Sensor
Max. Image Size
Mx Sensor Module
Max. Image Size
Thermal Image Sensor
Image Formats
(Independent of Type,
Per-Sensor Setting)
Max. Frame Rate
Mx sensor module
Max. Frame Rate
Thermal Image Sensor
Image Compression MxPEG, M-JPEG, JPEG, H.264
Internal DVR MicroSD card pre-installed (SDHC)
External
Video Ring Buer
Soware (Included) MxManagementCenter video management soware
Image Processing
Virtual PTZ Digital pan/tilt/zoom, continuous up to 8X
Mx-S16 (all combinations of Day/Night/Thermal/Thermal-TR sensor
modules)
10 to 270 mm (35 mm format), hor. angles of view 180° to 8° (6MP)
43, 65, 135 mm (in 35 mm format),
45°, 25°, 17° horizontal angle of view
Color sensor (6MP): 0.1 Lux at 1/60 s, 0.005 Lux at 1 s
Black&White sensor (6MP): 0.02 Lux at 1/60 s,
0.001 Lux at 1/1 s
NETD typ. 50 mK, IR range 7.5 to 13.5 μm
Range of temperature measuring: –40 to 550 °C/–40 to 1,022 °F
Precision Sensor Module Thermal(-TR): ±10 K of the thermal radiation received at the sensor
1/1.8“ CMOS, 6MP, progressive scan
Uncooled microbolometer, 336x252 pixels
Color: 3072x2048 (6MP), 6144x2048 (12MP)
Black&White: 3072x2048 (6MP), 6144x2048 (12MP)
Can be scaled up to 3072x2048 (6MP), automatically scaled to size
of Mx sensor module
3072x2048 (6MP), 2592x1944 (5MP),
(Full-HD),
1280x960 (MEGA), 1280x720 (HD), 1024x768, 800x600, 768x576
(D1-PAL),
704x576 (TV-PAL), 640x480, 384x288, 320x240, 160x120,
custom formats
• MxPEG* (max): 42@HD (1280x720), 34@Full-HD, 24@QXGA,
15@5MP, 12@6MP, 6@2x6MP
• M-JPEG* (max): 26@HD (1280x720), 13@Full-HD, 9@QXGA,
5@5MP, 4@6MP, 2@2x6MP
• H.264 (max): 25@Full-HD, 20@QXGA
*Single core use only
9 fps (when displaying an Mx sensor module and a thermal sensor
module, the overall frame rate of the camera is reduced to 9 fps)
Directly on NAS or PC/Server, no additional recording soware
required
Backlight compensation, automatic white balance, image distortion correction, panorama correction,
MxActivitySensor
2048x1536 (QXGA),
video motion detection,
1920x1080
Video Motion detection, MxActivitySensor, external signals, tem-
Alarm/Events
Microphone and
Speaker
Audio Functions Lip-synchronous audio, two-way communication, audio recording
Interfaces
Video Telephony
Security
Certications
Power Supply
Operating Conditions
Protection Against
Mechanical Impact
Power Consumption Typ. 5 W, max. 7 W
Dimensions/Weight S16
Dimensions/Weights
Sensor Modules
Dimensions/Weights
Thermal Sensor
Modules
Weight Connection
Cable 2 m
(per sensor module)
Standard Delivery
perature sensor, PIR, microphone, shock detector (with rmware
version 5.0.1 and higher), notication via e-mail, FTP, IP telephony
(VoIP, SIP), visual/sound alarms, pre- and post-alarm images
Microphone integrated in optical sensor modules and
BlockFlexMount modules (except CS-Mount variants and SMA-S6D/N/L500); ext. microphone and ext. speaker can be connected
Ethernet 100Base-T (patch or installation cable), MiniUSB; inputs/
outputs and RS232 via accessories,
ext microphone and ext. speaker
VoIP/SIP, two-way communication, remote controlling using key
codes, event notication
User/group management, HTTPS/SSL, IP address lter, IEEE 802.1x,
intrusion detection, digital image signature
EN55022:2010; EN55024:2010; EN50121-4:2006, EN61000-6-1:2007;
EN 61000-6-2:2005, EN61000-6-3:2007+A1:2011, EN61000-64:2007+A1:2011, AS/ NZS CISPR22:2009+A1:2010, CFR47 FCC
part15B
Year-round Power-over-Ethernet (IEEE 802.3af);
PoE class variable
IP66, –30 to 60 °C/–22 to 140 °F,
air humidity up to 90–100% (according to EN 50155 Chap. 12.2.5)
Mx-S16 Body: IK06
Width x height x depth: 115 x 130 x 33,5 mm; weight: approx. 430 g
(without sensor modules, see below)
SMA-S-6D/N/L016: Ø x D: 43 x 45 mm (installation dim.), weight 85 g
SMA-S-6D/N/L041/079: Ø x D: 43 x 57 mm (installation dim.), weight
111 g
SMA-S-6D/N/L061/119/237: Ø x D: 43 x 60 mm (installation dim.),
weight 122 g
SMA-S-6D/N/L500: Ø x D: 43 x 60 mm (installation dim.), weight 160 g
See separate product documentation
Sensor Module Thermal(-TR)»
approx. 68 g/0.14 lb
Housing (high-resistance composite, PBT), white and base plate
aluminum blue anodized, shock-resistant dome for
L016
sensor module, coated glass pane for all other sensor modules, protective Germanium cover for thermal image sensor,
mounting supplies, mounting wrenches, 50 cm/20 in patch cable,
soware, MicroSD card (SDXC, SDHC installed)
(according to IEC 62262/EN 50102)
«Quick Install
SMA-S-6D/N/
Dimensions/Drilling Template
100 mm/3.94 in
110 mm/4.33 in
8.50 mm/0.33 in
115 mm/4.53 in
100 mm/3.94 in
Dia. 5.50 mm/0.22 in
13.50 mm/0.53 in
M6
130 mm/5.12 in
47.50 mm/1.87 in
33.50 mm/1.32 in
5 mm/
0.20 in
130 mm/5.12 in
110 mm/4.33 in
115 mm/4.53 in
100 mm/3.94 in
100 mm/3.94 in
0.33 in
100 mm/3.94 in
8.5 mm/
DualMount
(accessory)
MOBOTIX, the MX logo, MxControlCenter, MxEasy, MxPEG and MxActivitySensor are trademarks of
MOBOTIX AG registered in the European Union, the U.S.A., and other countries • Information subject to
change without notice • MOBOTIX does not assume any liability for technical or editorial errors or omissions
contained herein • All rights reserved • © MOBOTIX AG 2017
Declaration of Conformity: www.mobotix.com > Support > MxMedia Library > Certicates
SurroundMount
(accessory)
Manuals and drilling templates:
HaloMount
(accessory)
SpeakerMount
(accessory)
PTMount
(accessory)
MOBOTIX AG
Kaiserstrasse
D-67722 Langmeil
Tel.: +49 6302 9816-103
Fax: +49 6302 9816-190
sales@mobotix.com
www.mobotix.com
Loading...