Mobotix Mx-Q26A-6N016 User Manual
1.12
1.11
1.13
100mm
Dia. 5.5mm
100mm
141.4 mm
4x
Click!
Click!
Accessories
Mx-Q26A/B* with
Outdoor Wall Mount
Mx-Q26A/B* with
Cavity Wall Installation Set
Mx-Q26A/B* with
On-Wall Set
Mx-Q26A/B* with
Vandalism Kit
Mx-Q26A/B* with
On-Wall Set 10°
Q26 Hemispheric
Quick Install
32.833-003_EN_04/2018
*Variant Mx-Q26B supports MOBOTIX MxBus modules
Standard Delivery Q26
1.1
1.16
1.15
1.14
1.10
1.9
1.2
1.8
1.6
1.7
1.3
1.5
1.4
Item Count Part Name
1.1 1 Camera housing
1.2 1 Lens (installed)
1.3 1 Lens wrench
1.4 1
1.5 1 Ethernet patch cable CAT5 0.5 m/1.64
1.6 1 Allen wrench 3 mm
1.7 1 Allen wrench 2 mm
1.8 1 Torx wrench TX20
1.9 1 Outer shell
1.10 4 Mounting ring
1.11 4 Stainless steel washers 5.3 mm dia.
1.12 4 Dowels 8 mm
1.13 4
1.14 4
1.15 1
1.16 2 Cable lock with bayonet catch (Ethernet patch cable, MiniUSB)
MicroSD card (SDXC, SDHC pre-installed)
Stainless steel Torx screws 4.5x60 mm
Stainless steel washers 4.3 mm dia.
Stainless steel Allen screws M4x16 mm
Connections and Initial Operation of the Q26
You can nd detailed information on the installation and connections of the Q26 in the Q25 Camera Manual (PDF, available on www.mobotix.com >
Support > Download Center > Documentation > Manuals).
Please note that the boot options of this camera have changed compared to its predecessor (see «Boot Options of the Q26» on page 1) and the camera only has one key ("R"). Regarding the rest of the initial operation of the Q26, please see the Q25 Camera Manual in Chapter 3, «Initial Operation». All
other tasks require access to the camera’s user interface in the browser. Enter the camera’s IP address into the address bar of the browser (user "admin",
password "meinsm"; password must be changed upon rst login – camera soware V5.1.x and higher).
MxBus
Outer shell
Camera
Mounting
ring
"R" key
LEDs
Lens
Network connection
Slot for MicroSD card
(inside)
USB
Mounting Options of the Q26
Prepare the Camera
Remove the outer shell of the Q26 (if installed). Then, remove the bayonet
lock and the blue plug from the network connection. Insert the patch
cable (item 1.5) into the network connection and secure it again with the
bayonet lock.
Installation on Walls or Ceilings Without Accessories
Aer drilling the holes for xtures (see «Drilling Template Without Accessories»), attach the mounting ring of the Q26 at the designated position using
dowels and screws. Next, connect the cabling, point the camera into the
viewing direction and adjust the focus of the lens (see «Adjusting the Lens
Focus of the Q26» on page 2). Finally, install the camera's outer shell.
Installation With On-Wall Set/On-Wall Set 10° (Accessory)
Aer drilling the holes for xtures (see «Drilling Template Without Accessories»), attach the On-Wall Set at the designated position using dowels
and screws, then lead the cabling into the On-Wall Set. Next, remove the
mounting ring of the Q26, connect the cabling and install the camera on
the On-Wall Set. Finally, install the camera's outer shell.
Installation With Cavity Wall Installation Set (Accessory)
Aer cutting out the hole (see «Drilling Template Without Accessories»), remove the mounting ring of the Q26 and install the camera in
the Cavity Wall Installation Set. Next, connect the cabling and install the
camera together with the Cavity Wall Installation Set into the cut-out and
fasten it using the winged cams. Finally, press the decoration ring onto the
camera and lock it in place using the toothed wrenches.
Installation With Outdoor Wall Mount (Accessory)
Remove the cover plate of the Outdoor Wall Mount. Aer drilling the
holes for xtures (see «Drilling Template Without Accessories»), attach
the Outdoor Wall Mount at the designated position using dowels and screws,
then lead the cabling into the mount. Next, remove the mounting ring of
the Q26, connect the cabling and click the camera into the clamps of the
cover plate of the Outdoor Wall Mount. Then attach the cover plate with the
camera to the Outdoor Wall Mount. Finally, install the camera's outer shell.
Installation With Pole Mount and Outdoor Wall Mount (Accessory)
Lead the cabling from the rear through the Pole Mount and attach to a pole
(using steel straps). Then attach the Outdoor Wall Mount to the Pole Mount.
The remaining installation of the Q26 follows the steps under «Installation
With Outdoor Wall Mount (Accessory)» above.
Installation of the Vandalism Kit (Accessory)
Remove the lens using the lens wrench and remove the lens gasket. Screw
the lens back into the lens mount and correct the lens' focus (see «Adjusting
the Lens Focus of the Q26» on page 2). Screw in the reinforced dome
and set the four spacers onto the mounting ring of the camera. Place the
stainless steel outer shell onto the camera and tighten it using the four
security screws.
Inserting/Exchanging the SD Card
All camera models can use the integrated MicroSD card (SDHC) to record video data. In order to exchange the MicroSD card, please proceed as outlined
in the following instruction. For information on reliable SD cards, please see the MOBOTIX website www.mobotix.com > Support > Download Center >
Documentation > White Lists in the document MicroSD Card Whitelist for MOBOTIX Cameras.
When replacing the SD card, make sure that recording has been deactivated in the browser (Admin Menu > Storage > Storage on External File Server /
Flash Device; activate recording again in the same dialog).
1. Remove the SD card
Remove the back of the camera housing. If a
MicroSD card has been installed, gently press
with your nger as indicated by the arrow until
you hear a click. Then release the SD card. The
card is protruding slightly and can be easily
removed.
2. Insert the SD card
Insert the MicroSD card and gently press with
your nger as indicated by the arrow until you
hear another click. Make sure that the SD card
is fully inserted. Install the back of the camera
housing.
Boot Options of the Q26
By default, the camera starts as DHCP client and automatically tries to get
an IP address from a DHCP server. To start the camera in a mode dierent
from the default mode, you can activate the boot menu of the camera.
1. Preparing the Camera
• Disconnect the camera's power supply.
• Make sure that you have suitable item such as a paper clip at hand,
but never use sharp or pointed objects!
• Reconnect the power supply of the camera.
2. Activating the Boot Menu
The red LED lights up 5 to 10 seconds aer establishing the power supply and will stay on for 10 seconds.
Briey press the key by inserting the paper clip into
the hole indicated by the red circle in the gure. The
camera enters the boot menu, ready for selecting one
of the boot options.
The LED now ashes once and repeats the ash signal aer pausing
for one second (the number of ashes indicates the current boot option).
To go to the next boot option, briey press the key again (< 1 sec). Aer the
last boot option, the camera returns to the rst option (LED ashes once).
LED
ashes
*Only on cameras with audio option and installed speaker.
1 x —
2 x
3 x
4 x
Boot
Option
Factory
Defaults
Automatic
IP Address
Recovery
System
Meaning
This option is not used on this camera
model.
Starts the camera with factory defaults
(factory default IP address, users and
passwords will not be reset).
Starts the camera as DHCP client and
tries to obtain an IP address from a DHCP
server. If a DHCP server cannot be found
or no IP address can be obtained, the
camera starts with its factory default
address.
Starts the camera with the recovery system, e.g., in order to recover from a failed
update of the camera soware.
Audio
Conrmation*
—
Boing
Boing Boing
Alarm Sound
3. Selecting a Boot Option
Press the paper clip longer (> 2 sec) into the hole. The camera conrms the
selection by ashing rapidly three times. You can now remove the paper
clip. Aer 20 sec, the camera will conrm the selection by playing a sound
according to the table above.
If nothing is selected, the camera will resume its normal boot process
aer a certain time.
100 mm/3.94 in
100 mm/3.94 in
www.mobotix.com > Support > Download Center > Documentation > Manuals > Q26 Hemispheric
§
§
Adjusting the Lens Focus of the Q26
If installed, remove the dome (using the wide side of the lens wrench,
item 1.3) before proceeding.
Check the live image from the camera in the browser (enter the camera's
IP address in the browser address bar). Activate the focusing aid in the
browser (Focusing Aid quick control, Activated value).
Important Notes
Safety Warnings
Notes on Installing:
• This product must not be used in locations exposed to
the dangers of explosion.
• Make sure that you install this product as outlined in Chapter 2,
«Installation» of the corresponding manual. A faulty installation can
damage the camera!
• When installing this product, make sure that you are only using genuine MOBOTIX parts and MOBOTIX connection cables.
• Only install this product on suitable, solid materials that provide for
a sturdy installation of the xing elements used.
Electrical installation: Electrical systems and equipment may
only be installed, modied and maintained by a qualied
electrician or under the direction and supervision of a quali-
ed electrician in accordance with the applicable electrical guidelines.
Make sure to properly set up all electrical connections.
Electrical surges: MOBOTIX cameras are protected against
the eects of small electrical surges by numerous measures.
These measures, however, cannot prevent the camera from
being damaged when stronger electrical surges occur. Special care should
be taken when installing the camera outside of buildings to ensure proper
protection against lightning, since this also protects the building and the
whole network infrastructure.
Max. power consumption of attached extension modules:
The power consumption of all attached MxBus modules must
not exceed 2,5 W. When attaching modules to the MxBus
connector and the USB socket, the power consumption of all attached
modules must not exceed 3 W, if the camera is powered by PoE class 3.
If PoE class 2 is used, the power consumption of all attached modules
must not exceed 1 W!
Never touch the lens: Due to the high performance of the Q26,
the area of the image sensor can get quite hot, especially when
the ambient temperature is also high. This does not aect the
proper functioning of the camera in any way. For this reason, the product
must not be installed within the reach of persons without dome.
Using the lens wrench (item 1.3), carefully turn
the lens in clockwise or counter-clockwise
direction until the red area of the focusing
aid is as small as possible.
Once the focus is adjusted properly, deactivate
the focusing aid again (Focusing Aid quick
control, Disabled value).
Reinstall the dome, if required.
Power o before opening the camera: Make sure the power
supply to the camera is disconnected before opening the
camera housing (e.g., when exchanging the SD card or when
opening the body to attach wires).
Network security: MOBOTIX products include all of the necessary conguration options for operation in Ethernet networks in compliance with data protection laws. The operator
is responsible for the data protection concept across the entire system.
The basic settings required to prevent misuse can be congured in the
soware and are password-protected. This prevents unauthorized parties
from accessing these settings.
Legal Notes
Legal aspects of video and sound recording: You must com-
ply with all data protection regulations for video and sound
monitoring when using MOBOTIX products. Depending on
national laws and the installation location of the Q26, the recording of
video and sound data may be subject to special documentation or it may
be prohibited. All users of MOBOTIX products are therefore required to
familiarize themselves with all applicable regulations and to comply with
these laws. MOBOTIX AG is not liable for any illegal use of its products.
Disposal
Electrical and electronic products contain many valuable
materials. For this reason, we recommend that you dispose of
MOBOTIX products at the end of their service life in accordance
with all legal requirements and regulations (or deposit these
products at a municipal collection center). MOBOTIX products must not be
disposed of in household waste! If the product contains a battery, please
dispose of the battery separately (the corresponding product manuals
contain specic directions if the product contains a battery).
Disclaimer
MOBOTIX AG does not assume any responsibility for damages,
which are the result of improper use or failure to comply to the
manuals or the applicable rules and regulations. Our General
Terms and Conditions apply. You can download the current version of the
General Terms and Conditions from our website at www.mobotix.com
by clicking on the COS link at the bottom of every page.
Technical Specications Q26
Mx-Q26A/B*-6D016 (daylight image sensor, color)
Model Variants
Lens Option B016 (focal length 1.6 mm, f/2.0, image angle 180°x180°)
Sensitivity
Image Sensor 1/1.8“ CMOS, 6MP (3072x2048), Progressive Scan
Max. Image Size 6MP (3072x2048)
Image Formats
Max. Frame Rate
Video Codec
ONVIF ONVIF-S (camera soware V5.2.x and higher, 2
DVR
Soware MxManagementCenter
Image Processing
Mx-Q26A/B*-6N016 (night image sensor, Black&White)
*Variant Mx-Q26B supports MOBOTIX MxBus modules
Color sensor (daylight): 0,1 lx @ 1/60s; 0,005 lx @ 1s
Black&White sensor (night): 0,02 lx @ 1/60s; 0,001 lx @ 1s
Freely congurable 4:3, 8:3, 16:9 or custom formats (image cropping),
e.g., 2592x1944 (5MP), 2048x1536 (QXGA), 1920x1080 (Full-HD),
1280x960 (MEGA)
MxPEG: 42@HD(1280x720), 34@Full-HD, 24@QXGA, 15@5Mp,
12@6MP
M-JPEG: 26@HD(1280x720), 13@Full-HD, 9@QXGA, 5@5Mp, 4@6MP
H.264: 25@Full-HD, 20@QXGA
MxPEG, M-JPEG, JPEG (max. output size 6MP)
H.264 (max. output size QXGA, bandwidth limitation applicable)
In the camera on MicroSD card (SDXC, SDHC pre-installed)
External, on USB device
External, on NAS
Separate live image and full image recording – MxFFS with archiving
function
Pre- and post-alarm images
Automatic DVR monitoring with error notication
MxLEO, backlight compensation, automatic white balance,
distortion correction
nd
half of 2018)
PTZ Digital pan/tilt/zoom, continuous up to 8X
Temperature sensor, shock detector (with rmware version 5.0.1 and
Alarm/Events
Intelligent Video Analysis MxActivitySensor, video motion analysis, MxAnalytics
Audio
Interfaces
Security
Certications
Power Supply Power over Ethernet IEEE 802.3af
Power Consumption Typ. 4 W
Power Consumption of
External Devices
Protection Classes
Ambient Temperature –30 to 50 °C/–22 to 122 °F
Dimensions/Weight
Standard Delivery
higher), microphone, additional sensors/IOs via MxMessageSystem,
notication via e-mail, FTP, IP telephony (VoIP, SIP), visual/sound
alarms, pre- and post-alarm images
Microphone/speaker, both 16bit/16kHz (HD wideband audio)
Lip-synchronous audio, audio recording
VoIP/SIP telephony, intercom, remote controlling using key codes
Ethernet 100Base-T, MiniUSB, MxBus*;
inputs/outputs and RS232 via accessories
*Only variant Mx-Q26B
User/group management, HTTPS/SSL, IP address lter, IEEE 802.1x,
intrusion detection, digital image signature, MxFFS
EN55022:2010; EN55024:2010; EN50121-4:2006, EN61000-6-1:2007;
EN 61000-6-2:2005, EN61000-6-3:2007+A1:2011, EN61000-64:2007+A1:2011, AS/ NZS CISPR22:2009+A1:2010, CFR47 FCC part15B
At MxBus: max. 2,5 W, at USB: max. 2.5 W, total max. 3 W
The power consumption of the camera will increase accordingly!
IP66
IK06, IK10 with Vandalism Kit
Diameter x height: 160 x 48 mm/6.30 x 1.89 in; weight: approx.
350 g
Housing (high-resistance composite, PBT) white, mounting supplies,
mounting wrenches, 50 cm/20 in patch cable, soware, MicroSD card
(SDXC, SDHC installed)
Dimensions
Q26 without accessories
ø 160 mm/6.30 in
On-Wall Set
ø 160 mm/6.30 in
Cavity Wall Installation Set
Clamping range
6 to 22 mm/
0.24 to 0.87 in
0.95 in
48 mm/1.89 in
85 mm/3.35 in
ø 180 mm/7.09 in
On-Wall Set 10°
ø 166 mm/6.54 in
24.1 mm/
2.91 in
74 mm/
Vandalism Kit Outdoor Wall Mount
ø 160 mm/6.30 in
Drilling Template Without Accessories
53 mm/2.09 in
125 mm/4.92 in
201 mm/7.91 in
216 mm/8.50 in
ø 5.5 mm/0.22 in
141.4 mm/5.57 in
Installation with mounting ring (without accessories)
Camera without
accessories
Further information on www.mobotix.com:
• Products > Indoor Cameras > Q26 Hemispheric
• Support > Download Center > Documentation > Certicates & Declarations of Conformity
MOBOTIX, the MX logo, MxPEG and MxActivitySensor are trademarks of MOBOTIX AG registered in the European Union, the U.S.A., and other countries • Information subject to change without notice • MOBOTIX does
not assume any liability for technical or editorial errors or omissions contained herein • All rights reserved •
© MOBOTIX AG 2017
On-Wall Set/
On-Wall Set 10°
Cavity Wall Installation Set Outdoor Wall Mount Pole Mount
Manuals and Drilling Templates:
Loading...