Mobotix MX-CAMIO-OPT-M12 User Manual

Megapixel

1280 x 960

software zoom

Security-Vision-SystemsSecurity-Vision-Systems

30 Frames/s

VGA (640 x 480)

10 fps Mega

-22°F to +140°F

Weatherproof

-30°C to +60°C, IP65

no heating necessary

IEEE 802.3af

PoE

network power

even in winter

microphone & speaker

Audio

bi-directional via IP

variable framerates

Video SIP Client

IP Telephony

alarm notify,

cam remote control

CamIO

User Manual

X

MOBOTIX

com

.

Video motion

multiple windows

precision pixel-based

lip-syncronized audio

Recording

event-ringbuffer

30 cams each 30 fps

Live viewing

30 cams at 30 fps

all on one screen

Backlight

safe using CMOS

without mechanical iris

Vandalism-protected

Lamp

Door

MOBOTIX

CamIO

Out1

8 to 48 V~

Out2

123

4

230 V~/115V~

56

7 8 10 11 1314 15 16

In1

In2

Line-In

Speaker

8

Microphone with
pre-amplifier

Speaker

8 to 230 V~ (8 to 48 V~)

8 to 230 V~ (8 to 48 V~)

Complete integration for web and security

Current PDF File:

www.mobotix.com > Support > Manuals

RJ45

Wall bracket

with cable cover

for RJ45 wall outlet

Robust

no moving parts

fiber glass housing

MOBOTIX AG • Security-Vision-Systems • Made in Germany

MOBOTIX ... the new face of IP video

www.mobotix.com • [e-mail] • 9.11.2007

MOBOTIX CamIO User Manual

Caution

Only qualified personnel may install and open the CamIO and con­nect it to the mains power; make sure that the relevant regula­tions of your country are respected!

It is imperative that all electrical wires have been disconnected
from the mains power when working on or servicing the CamIO!
Please also make sure to adhere to the applicable regulations for
this kind of work!

MOBOTIX will not assume any responsibility for damages from
faulty installations or inappropriate use!

Notes

Note: MOBOTIX offers inexpensive seminars that include a workshop and

practical exercises: Basic Seminar three days, Advanced Seminar two
days.

For more information, see www.mobotix.com

© MOBOTIX AG • Security-Vision-Systems • Made in Germany

www.mobotix.com • [e-mail]

MOBOTIX CamIO User Manual

CamIO User Manual

1 INTRODUCTION 4

1.1 MOBOTIX CamIO Concept 6

1.2 The MOBOTIX CamIO and MOBOTIX Cameras 8

1.2.1 Functional Overview of the CamIO Models 8

1.2.2 Connection Cables between CamIO and MOBOTIX Cameras 9

1.3 Important Notes 10

1.3.1 Safety Regulations 10

1.3.2 Cables for the MOBOTIX CamIO 10

1.3.3 Minimum Load at the Signal Outputs 11

1.3.4 Safety Notes for Operating the MOBOTIX CamIO 11

1.3.5 Maximum Cable Lengths 12

1.3.6 Charging the Rechargeable Battery (CamIO-ACplus) 12

1.3.7 Weatherproofness, Temperature Range 12

1.3.8 Cleaning Instructions 12

1.3.9 Additional Information 12

1/56

2 MOUNTING 14

2.1 Delivered Parts, Components, Dimensions and Connectors 14

2.1.1 Delivered Parts and Components 14

2.1.2 Wall Mount Foot and Housing 15

2.1.3 Dimensions and Drilling Template 16

2.1.4 Connectors and Wiring 20

2.2 Information on Connecting the MOBOTIX CamIO 22

2.3 Mounting the CamIO Wall Mount and the Control Cable 24

2.3.1 Mounting with an M12 Camera 24

2.3.2 Mounting with an M22 Camera 26

2.4 Mounting the CamIO Housing and Installing the Cables 28

2.4.1 Mounting the CamIO Housing on the Wall 28

2.4.2 Power Supply of the CamIO 29

2.4.3 Ethernet Connection of the CamIO 32

2.5 Connecting External Components to the CamIO 33

2.5.1 Connecting External Devices, Sensors and Audio Devices 33

2.6 Mounting the Camera on the CamIO 36

2.6.1 Connecting the Additional Speaker in the Wall Mount Foot 36

2.6.2 Connecting the Ethernet and the CamIO Control Cables 37

2.7 Wiring, Fire Prevention, Lightning and Surge Protection 38

2.7.1 Wiring 38

2.7.2 Fire Prevention 38

2.7.3 Lightning and Surge Protection 38

2.8 Accessories, Replacement Parts 40

© MOBOTIX AG • Security-Vision-Systems • Made in Germany

www.mobotix.com • [e-mail]

2/56

MOBOTIX CamIO User Manual

3 OPERATION OF THE CAMIO 42

3.1 Activating the CamIO 42

3.2 Configuration Sample 43

3.2.1 Functional Overview 43

3.2.2 Terminal Connections of the CamIO 44

3.2.3 Overview of the Configuration Steps 44

3.2.4 Configuring the MOBOTIX Camera 45

3.2.5 Configuring a Softphone 51

4 TECHNICAL SPECIFICATIONS 52

APPENDIX: DECLARATION OF CONFORMITY

DRILLING TEMPLATE (SCALE 1:1)

Download the latest versi­on of this document as a
PDF file from
www.mobotix.com:
Support> Manuals

Note

Download the latest version of this document as a PDF file from
www.mobotix.com, Support> Manuals.

Information subject to change without notice!

Copyright © 1999-2007 MOBOTIX AG, Kaiserslautern, Germany.

All rights reserved. MOBOTIX, MxPEG and MxControlCenter are worldwide
trademarks of MOBOTIX AG. Microsoft, Windows and Windows Server are reg­istered trademarks of Microsoft Corporation. Apple, the Apple logo, Mac and
Mac OSX are trademarks of Apple Inc. Linux is a trademark of Linus Torvalds.
All other marks and names mentioned herein may be trademarks or registered
trademarks of the respective owners.

© MOBOTIX AG • Security-Vision-Systems • Made in Germany

www.mobotix.com • [e-mail]

MOBOTIX CamIO User Manual

Notes

3/56

© MOBOTIX AG • Security-Vision-Systems • Made in Germany

www.mobotix.com • [e-mail]

4/56

MOBOTIX CamIO User Manual

1 INTRODUCTION

All CamIO models can be
used with the MOBOTIX
M12 and M22 cameras
(IT and Secure models).

The CamIO can switch
Ohm resistive loads with
max. 5A, (max. 500W
lamps at 230V or
300W lamps at 115V).

The MOBOTIX CamIO is the expansion box for connecting the MOBOTIX cameras

M12 and M22M (IT and Secure models). In the security and home automation

fields, the CamIO is the ideal supplement to the MOBOTIX cameras, if you want to
switch lamps, doors, control wires, pushbuttons or other external devices, evaluate
other sensors than those in the camera or use external audio devices (M12 models
only).

An external device (e.g. a lamp) connected to the CamIO-AC/ACplus can be
powered directly by the CamIO and is switched on or off using the first signal out
put of the MOBOTIX camera. The second signal output can be used for potential
free switching of another external device (e.g. door opener; max. 230V~ or 48V~/
68V=, depending on the CamIO model). This signal output can also be used to
connect the MOBOTIX camera to the input of an alarm system, for example.

You can also attach external sensors to the MOBOTIX camera via the CamIO, e.g.
to evaluate remote sensors, such as light barriers, reed switches, external PIR sen­sors or the output of an alarm system.

© MOBOTIX AG • Security-Vision-Systems • Made in Germany

www.mobotix.com • [e-mail]

MOBOTIX CamIO User Manual

Battery

5/56

When mounting the MOBOTIX CamIO, the foot of the CamIO wall mount replaces
the original foot of an M12 or M22 camera mount. The foot of the CamIO wall
mount covers the CamIO and reliably protects it against atmospheric exposure

(IP65). In addition, the foot of the CamIO wall mount also contains an additional
speaker, which is more powerful than the camera's internal speaker.

CamIO models

• CamIO-PoE: This model is supplied using

PoE (IEEE 802.3af), which powers the camera

and the CamIO itself. The signal output Out1
can switch one external device (max. 5A), if
max. 48V~ or 68V= have been connected
to terminals 1 and 2; the signal output Out2
can be used for potential-free switching of
another external device (max. 5A) with max.
48V~ or 68V=.
The CamIO-PoE also features two signal in-

puts, one audio input (Line-In) and one
audio output for directly connecting the supplied additional speaker

(max. 2.5W/8Ω).

MX-CAMIO-POE

PoE

Currently, the audio
features of the CamIO
can only be used with
M12 cameras. A future
version of the CamIO
will support external
speakers and micro­phones also on M22 cam­eras.

• CamIO-AC: This model has the same fea­tures as the CamIO-PoE, but it can be con­nected directly to utility power (230V~/
115V~) and can power one external device

with up to 230V~ current (Ohm resistive

load, max. 5A, max. 500W lamp on 230V~,
max. 300W on 115V~). It can also be used
for potential-free switching of a second exter­nal device (max. 5A) with up to 230V~/

115V~ at signal output Out2.

• CamIO-ACplus: In addition to the features of
the CamIO-AC, the CamIO-ACPlus has a re-

chargeable battery, which provides a
backup power supply for the M12 models

even during power failures (approx. 45 min­utes at 20°C/68°F, 20 minutes at -20°C/-4°F).

The CamIO AC and ACplus
versions are VDE-certi-

fied

230 V

115V

MX-CAMIO-AC-230

MX-CAMIO-AC-115

Using the backup power
feature of the CamIO­ACplus requires a
MOBOTIX M12. M22
cameras do not support
this feature yet.

© MOBOTIX AG • Security-Vision-Systems • Made in Germany

www.mobotix.com • [e-mail]

MX-CAMIO-ACPLUS-230

MX-CAMIO-ACPLUS-115

6/56

MOBOTIX CamIO User Manual

1.1 MOBOTIX CamIO Concept

Simple Installation

When designing the MOBOTIX CamIO, special focus was placed on easy installa­tion of the expansion box. The supplied drilling template facilitates mounting the
CamIO and connecting the cabling for devices and data connections is easy,
secure and weatherproof.

Directly supplying power to and switching of external devices

To supply power to an ex­ternal device (terminals 3
and 4), make sure that
the CamIO itself is con­nected to the power sup­ply (terminals 1 and 2).

The CamIO-AC and CamIO-ACplus models can directly power one device at sig-

nal output Out1 (230V~/115V~ at terminals 1 and 2 required), allowing you to

switch this device from the MOBOTIX camera (max. 5A, max. 500W lamp on
230V, max. 300W on 115V). You can use the second signal output Out2 for po­tential-free switching of another external device.

The CamIO-PoE model has similar possibilities for switching devices, but can only
switch loads of up to 48V~/68V=.

ETHERNET
CAMERA

ETHERNET

P

N

© MOBOTIX AG • Security-Vision-Systems • Made in Germany

www.mobotix.com • [e-mail]

MOBOTIX CamIO User Manual

7/56

Backup power using the CamIO-ACplus

The integrated rechargeable battery of the CamIO-ACplus model can bridge
smaller power failures and thus protects the integrity of the video and audio data.
At room temperature (20°C/68°F), the CamIO can power a MOBOTIX M12D for
about 45 minutes; at -20°C (-4°F), the CamIO still provides 20 minutes of backup
power. Providing backup power for an M22M using a CamIO-ACplus is currently
not possible.

Using external sensors

Using the two signal inputs of the CamIO, the MOBOTIX camera can monitor exter­nal sensors and apply the different mechanisms available to the camera for storing
audio/video and for sending notification messages.

Connecting audio devices to M12 Cameras

Using the audio terminal of the MOBOTIX CamIO (Audio-Out), you can attach the

supplied external speaker in the wall mount foot to the MOBOTIX camera

(2.5W/8Ω; M12 models only). If you connect an external microphone via an ex­ternal pre-amplifier to the Line-In terminals of the CamIO, the MOBOTIX camera will
also use this input device. It is likewise possible to connect the Line-In terminals of
the CamIO to the Line-Out connector of a computer.

Weatherproof

The CamIO-ACplus can
provide backup power for
a MOBOTIX M12D for
about 45 minutes.

Using the backup power
feature of the CamIO­ACplus requires a
MOBOTIX M12. M22
cameras do not support
this feature yet.

Currently, the audio
features of the CamIO
can only be used with
M12 cameras. A future
version of the CamIO
will support external
speakers and micro­phones also on M22 cam­eras.

The weatherproofness of the MOBOTIX CamIO has been tested extensively and
has reached IP65 (absolutely dustproof and resistant against water jets). Special
attention has been paid to the waterproofness of the power cables, for which spe­cial cable seals have been developed.

Robust and durable

Like all other MOBOTIX products, the CamIO has been designed for a long product
life. The housing from PBT-30GF is robust and reliably protects the interior of the
CamIO.

© MOBOTIX AG • Security-Vision-Systems • Made in Germany

www.mobotix.com • [e-mail]

8/56

All CamIO models can be
used with MOBOTIX
M12 and M22 cameras
(IT/Secure models).

Using the backup power
feature of the CamIO­ACplus requires a
MOBOTIX M12. M22
cameras do not support
this feature yet.

MOBOTIX CamIO User Manual

1.2 The MOBOTIX CamIO and MOBOTIX Cameras

1.2.1 Functional Overview of the CamIO Models

CamIO-PoE

Mx-CAMIO-POE

Hardware Features

Outdoor - weatherproof IP65 IP65 IP65

Power Supply

Integrated rechargeable battery

PoE

-

CamIO-AC

Mx-CAMIO-AC-230

Mx-CAMIO-AC-115

230 V~ / PoE

115V~ / PoE

-

CamIO-ACplus

230 V~ / PoE

115V~ / PoE

Mx-CAMIO-ACPLUS-230

Mx-CAMIO-ACPLUS-115

X

Currently, the audio
features of the CamIO
can only be used with
M12 cameras. A future
version of the CamIO
will support external
speakers and micro­phones also on M22 cam­eras.

Concealed cabling

Features

Audio Out (speaker/microphone)

Line In (microphone with pre-amp.)

Signal outputs

Signal inputs

Input voltage (terminals 1 and 2)

M12

X

X

2

2

8 to 48 V~

11 to 68 V=

X

M22M

-

-

2

2

M12

X

X

2

2

X

M22M

-

-

2

22

230 V~

115V~

Note

In order to use all features of the CamIO, make sure that you are
activating it in the camera software (Admin Menu> Manage
Hardware Expansions). Please note that you will need a software
version 3.3.1.x or higher on the MOBOTIX M22M and a software
version 3.1.0.x or higher on the MOBOTIX M12.

X

M12

X

X

2

230 V~

115V~

© MOBOTIX AG • Security-Vision-Systems • Made in Germany

www.mobotix.com • [e-mail]

MOBOTIX CamIO User Manual

1.2.2 Connection Cables between CamIO and MOBOTIX Cameras

Two cables are required to connect the MOBOTIX camera to the CamIO:

• Ethernet cable: Establishes the data connection and the power supply to the
camera.

9/56

• Control cable: Connects the serial interface (M12) or the USB interface (M22)
of the camera in order to provide the signal outputs and inputs of the cam­era at the CamIO. The different cameras require different control cables,
which need to be ordered separately.

Control cable for the MOBOTIX M12

The control cable re­quired for connecting the
CamIO is not part of
the standard delivery.
Always order a corre­sponding control cable
for your M12 or M22.

Control cable for the MOBOTIX M22M

MX-CAMIO-OPT-M12

MX-CAMIO-OPT-M22

© MOBOTIX AG • Security-Vision-Systems • Made in Germany

www.mobotix.com • [e-mail]

10/56

MOBOTIX CamIO User Manual

1.3 Important Notes

1.3.1 Safety Regulations

Caution

Only qualified personnel may install and open the CamIO and con­nect it to the mains power; make sure that the relevant regula­tions of your country are respected!

It is imperative that all electrical wires have been disconnected
from the mains power when working on or servicing the CamIO!
Please also make sure to adhere to the applicable regulations for
this kind of work!

MOBOTIX will not assume any responsibility for damages from
faulty installations or inappropriate use!

For information on al­lowed cable diameters
and lengths, see chap­ter4,

Technical Specifi-

cations

.

1.3.2 Cables for the MOBOTIX CamIO

Only use cables, which have been approved for the pertinent type of installation.
Always observe the allowed wire cross-sectional sizes (see table below) and the
maximum cable lengths.

• Connecting the power supply: To provide the power
supply to the CamIO, a two-wire cable is required. A
ground conductor is not needed. If a power cable with

CamIO

ground conductor is used, this wire must not be con­nected in the junction box. Instead, connect the ground
conductor of any attached device in the junction box.

Ground

Lamp

Make sure that the fuse for this cable is not stronger
than 16A.

Junction box

• Connecting an electrical device: In order to provide power to an external
device (Ohm resistive load, max. 5A, 500W lamp on 230V, max. 300W
lamp on 115V), the CamIO switches two wires (phase conductor and neutral).

A ground conductor for grounding the external device needs to come
from the junction box.

• Connecting signal wires and external sensors: Use suitable installation ca­ble for connecting another relay or a signal line (e.g. to an alarm system) or
an external sensor.

• Connecting the Ethernet cable: Make sure that you
are using a suitable eight-wire Ethernet installation ca­ble CAT5 (or higher) for connecting the CamIO to the
patch panel of a structured wiring system in a building.

Make sure that you are completely removing the
shielding of the Ethernet cable and that no part of
the shielding touches the circuit board.

© MOBOTIX AG • Security-Vision-Systems • Made in Germany

www.mobotix.com • [e-mail]

MOBOTIX CamIO User Manual

11/56

Allowed Cable Dimensions Solid AWG

Bottom terminal (terminals 1 to 16)

Ethernet terminal (cutting clamps)

Cable diameters should be tailored to the electrical load and must follow the applicable regulations.

0.14 to 2.5 mm

0.13 to 0.31 mm

2

2

26 to 14

26 to 22

Note

The length of the cables for signal wires and external sensors is

not restricted. You need to make sure, however, that the minimum

voltage at the corresponding terminal is reached (see chapter4,

nical Specifications

). A possible loss of voltage due to the resistance of

Tech-

the wires needs to be considered.

1.3.3 Minimum Load at the Signal Outputs

In order to avoid oxidation of the relay points, you should use minimum loads of
5V=/100mA.

1.3.4 Safety Notes for Operating the MOBOTIX CamIO

When installing the wiring inside or outside of buildings, make sure you always ad­here to the relevant regulations on wiring, fire prevention and protection against
lightning.

AWG:
American Wire Gauge (for
measuring cable diame­ters)

MOBOTIX recommends having MOBOTIX devices installed only by certified special­ists accustomed to installing network devices and having proper respect for the ap­plicable regulations regarding lightning protection and fire prevention as well as
the current technology for preventing damages from electrical surges.

More information is available at an institution such as the International Electro-
technical Commission (IEC, www.iec.ch) or at a manufacturer of protection de-
vices against lightning and electrical surges, such as Dehn (www.dehn.de).

Wiring

When installing the wiring, make sure to follow these guidelines:

• Outdoors: Installing the camera outdoors requires special precautions and
measures regarding the cables as well as lightning and surge protection
(see further below in this section).

• Wire lengths: The cable segments must not exceed the maximum allowed
cable lengths in order to ensure proper data transfer (see also section3.3,

Connecting the Camera to the Network and to the Power Supply

, in the cor-

responding camera manual).

• Avoid induction: When running data cables parallel to existing regular
power lines or high-voltage wires, make sure you observe the minimum dis­tances to the power cables.

© MOBOTIX AG • Security-Vision-Systems • Made in Germany

www.mobotix.com • [e-mail]

12/56

MOBOTIX CamIO User Manual

Fire Prevention

When installing the power lines to the camera, make sure you always adhere to
the relevant regulations on wiring and fire prevention at the site of the installation.

Lightning and Surge Protection

To prevent damage from lightning and power surges, make sure you follow these
guidelines:

• Lightning conductors: In areas exposed to lightning (e.g. on roofs), a dis­tance holder (1m (3ft) above and away from the camera) and proper light­ning conductors need to be installed in order to prevent lightning strikes into
the camera and to ensure that the energy of a lightning strike is properly led
to the ground.

• Surge protection: Make sure you have installed proper protection against
electrical surges in order to prevent damage to the camera, the building and
the network infrastructure. This includes surge protectors for 19" racks, add­ing an uninterruptible power supply (UPS) to the MOBOTIX camera, and in­stalling surge arresters or similar for routers, switches, servers, etc.

1.3.5 Maximum Cable Lengths

According to UL regulations, the length of the cable to a MOBOTIX camera must
be limited to 140feet or less running outside of buildings. The installation must
comply with articles 725 and 800 of the National Electric Code.

1.3.6 Charging the Rechargeable Battery (CamIO-ACplus)

The CamIO-ACPlus model features a rechargeable battery, which provides
backup power supply even during power failures (approx. 45 minutes at 20°C/

68°F, 20 minutes at -20°C/-4°F). Please note that the full capacity of the recharge­able battery is only available after the CamIO has been attached to mains power
for at least 48 hours.

1.3.7 Weatherproofness, Temperature Range

The housing of the MOBOTIX CamIO is weatherproof (IP65, absolutely dustproof,
resistant against water jets) and can be used at temperatures from -30 to +60°C

(-22 to +140°F).

1.3.8 Cleaning Instructions

The housing of the MOBOTIX CamIO and the wall mount foot are made of fiber-re­inforced PBT-30GF. This material is robust, maintenance-free and can be cleaned
using a mild household detergent without solvents or abrasive particles.

1.3.9 Additional Information

For additional information on the MOBOTIX CamIO, see www.mobotix.com.

© MOBOTIX AG • Security-Vision-Systems • Made in Germany

www.mobotix.com • [e-mail]

MOBOTIX CamIO User Manual

Notes

13/56

© MOBOTIX AG • Security-Vision-Systems • Made in Germany

www.mobotix.com • [e-mail]

14/56

MOBOTIX CamIO User Manual

2 MOUNTING

2.1 Delivered Parts, Components, Dimensions and Connectors

2.1.1 Delivered Parts and Components

Allen screws M6x40 (item6)

Washers ø6.4mm (item7)

Speaker with audio

Allen wrench 5mm (item12)

cables (item11)

The control cable requi­red for connecting the
camera to the CamIO is
not part of the standard
delivery. Always order
the corresponding control
cable for your M12 or
M22.

NET plug (item5)
Screw caps for wall
mount (item10)

Control cable for the CamIO (not
included in delivery; needs to be
ordered separately!)

Item Count Part Name

1
2
3
4
5
6
7
8
9

10

11
12
13
14

1
1
1

8

1
4
8
4
4
4
2

1

1

1

CamIO Wall Mount Foot
CamIO Housing
Cover for wall mount
Cable seals (4x with 3, 4x with 5 fingers)
NET plug
Allen screws M6x40
Washers ø6.4mm
Wood screws 5x80mm
Dowels 8mm
Screw caps for wall mount
Speaker with audio cables (mounted in wall mount foot)
Allen wrench 5mm
Wood screw 3x10mm
Washer ø3.4mm

Cable seals with 3/5
fingers (item4)

Cover for wall mount foot (item3)

Wood screws 5x80mm (item8)

Dowels 8mm (item9)

© MOBOTIX AG • Security-Vision-Systems • Made in Germany

www.mobotix.com • [e-mail]

MOBOTIX CamIO User Manual

2.1.2 Wall Mount Foot and Housing

The MOBOTIX CamIO housing (item1) and the housing of the CamIO itself (item2)
are made of white, fiber-reinforced plastic (PBT-30GF, Polybutyleneterephtalate
with 30% fiberglass). This material is used heavily in the automotive industry and
is sturdy, resistant against high temperatures, environmental influences, chemicals,
etc.

CamIO Wall Mount Foot

Additional speaker
(pre-installed)

15/56

The additional speaker
can currently only be
used with M12 cameras.
A future version of the
CamIO will support ex­ternal speakers and mi­crophones also on M22
cameras.

CamIO Housing

NET connection for Ethernet cable to the camera

Connector for control
cable to the camera

Terminal connectors for
Ethernet link to the network

Terminal connectors for power supply, external devices, sensors and audio devices

© MOBOTIX AG • Security-Vision-Systems • Made in Germany

www.mobotix.com • [e-mail]

16/56

The appendix of this man­ual contains a 1:1 drilling
template for drilling the

dowel holes for the

CamIO.

MOBOTIX CamIO User Manual

2.1.3 Dimensions and Drilling Template

Dimensions of the MOBOTIX CamIO Housing

100mm/3.94in

100mm/3.94in

25mm/1in

© MOBOTIX AG • Security-Vision-Systems • Made in Germany

www.mobotix.com • [e-mail]

MOBOTIX CamIO User Manual

Dimensions of the MOBOTIX CamIO Housing with Wall Mount Foot

162.5mm/6.5in

17/56

136mm/5.4in 158mm/6.22in

© MOBOTIX AG • Security-Vision-Systems • Made in Germany

www.mobotix.com • [e-mail]

18/56

MOBOTIX CamIO User Manual

© MOBOTIX AG • Security-Vision-Systems • Made in Germany

www.mobotix.com • [e-mail]

MOBOTIX CamIO User Manual

19/56

© MOBOTIX AG • Security-Vision-Systems • Made in Germany

www.mobotix.com • [e-mail]

20/56

MOBOTIX CamIO User Manual

2.1.4 Connectors and Wiring

Terminal Connector for Power Supply, External Devices, Sensors and Audio De­vices

Make sure that you are adhering to the appli­cable regulations in your country regarding the
allowed cables when connecting the wires to the
terminal connector. Always observe the allowed
wire cross-sectional sizes (see table below).

5 6

7 8 10 11 13 14 15 16

1 2 3 4

AWG:
American Wire Gauge (for
measuring cable diame­ters)

If a power cable with
ground conductor is used
(three-wire cable), this
wire must not be con­nected at the junction
box! Instead, connect
the ground conductor in
the junction box and not
within the CamIO.

Allowed Cable Dimensions Solid AWG

Bottom terminal (terminals 1 to 16)

Cable diameters should be tailored to the electrical load and must follow the applicable regulations.

0.14 to 2.5 mm

2

26 to 14

Terminal Part Name Remark

1

2

3

Phase conductor L
Neutral conductor N

Out1 L (signal output 1)

Direct power supply for CamIO
and Out1
Ext. devices without individual
power supply, max. 5A, max.

4

5

Out1 N (signal output 1)

Out2a (signal output 2)

500W lamps
Ext. devices with individual power
supply 5 to 230V~, max. 5A

6

7
8

10

11
13
14
15
16

Out2b (signal output 2)

In2 + (signal input 2)
In2 - (signal input 2)
In1 + (signal input 1)
In1 - (signal input 1)
Speaker +
Speaker ­Line-In +
Line-In -

(min. 5V=, 100mA)
Ext. sensor 2, 8 to 230V~ (48V~)
(min. 2mA)
Ext. sensor 1, 8 to 230V~ (48V~)
(min. 2mA)
Ext. speaker can be connected
directly, max. 2.5W/8Ω
Ext. microphone with ext. pre­amplifier

© MOBOTIX AG • Security-Vision-Systems • Made in Germany

www.mobotix.com • [e-mail]

MOBOTIX CamIO User Manual

W

W

W

W

Terminal Connector and Wiring of the Ethernet Connector

Make sure that you are using a standard
CAT5 Ethernet cable for connecting the Ether­net cable to the Ethernet terminal connector
(see section 2.4.3,

the CamIO

). Always observe the allowed
wire cross-sectional sizes and the applied
connection standard. The color codes of the
individual wires are usually easy to spot at a CAT5 plug.

Ethernet Connection of

21/56

Allowed Cable Dimensions Solid AWG

Ethernet terminal (cutting clamps)

Cable diameters should be tailored to the electrical load and must follow the applicable regulations.

0.13 to 0.31 mm

Ethernet cabling today follows an EIA/TIA standard (

ance, TIA: Telecommunications Industry Association

2

EIA: Electronic Industries Alli-

), commonly T568B (AT&T

26 to 22

258A) is being used; older Ethernet cabling may have been connected according to
T568A:

Connection Standard T568B

Terminal TIA-568B Pair No.TIA-568 Color

8

7

6 (Rx-)

5

4

3 (Rx+)

2 (Tx-)

1 (Tx+)

4

4

3

1

1

3

2

2

Brown cable/white line

White cable/brown line

Green cable/white line

White cable/blue line

Blue cable/white line

hite cable/green line

Orange cable/white line

hite cable/orange line

AWG:
American Wire Gauge (for
measuring cable diame­ters)

Variant B - T568B

Connection Standard T568A

Terminal TIA-568A Pair No.TIA-568 Color

8

7

6 (Rx-)

5

4

3 (Rx+)

2 (Tx-)

1 (Tx+)

4

4

2

1

1

2

3

3

Brown cable/white line

White cable/brown line

Orange cable/white line

White cable/blue line

Blue cable/white line

hite cable/orange line

Green cable/white line

hite cable/green line

© MOBOTIX AG • Security-Vision-Systems • Made in Germany

www.mobotix.com • [e-mail]

Variant A - T568A

22/56

MOBOTIX CamIO User Manual

2.2 Information on Connecting the MOBOTIX CamIO

The CamIO can be used with a MOBOTIX M12 or an M22. Simply replace the origi­nal foot of the corresponding SecureFlex mount of the camera by the supplied foot
of the CamIO wall mount.

MOBOTIX M12 with CamIO

MOBOTIX M22M with CamIO

© MOBOTIX AG • Security-Vision-Systems • Made in Germany

www.mobotix.com • [e-mail]

MOBOTIX CamIO User Manual

Mounting the CamIO in four steps

Mounting the CamIO is done in four steps (or three, if no external devices are con­nected; skip step3 in this case):

1) Preparing the camera: Mounting the CamIO Wall Mount and the Control
Cable

Replace the foot of the original SecureFlex wall mount against the foot of the
CamIO wall mount. This step includes connecting the M12/M22 control cable
to the camera and guiding it and the network cable into the CamIO wall
mount (

2) Preparing the CamIO: Mounting the CamIO Housing and Installing the
Cables

First, mount the housing of the CamIO to a wall. This step involves connecting
the network cable and the power cable coming from the building infrastruc­ture to the CamIO (

3) Connecting External Components to the CamIO

This (optional) step involves connecting external devices, sensors and audio
devices to the CamIO (terminals 3 to 16 of the terminal connectors;

2.5

section 2.3

).

).

section 2.4

).

section

23/56

4) Mounting the Camera on the CamIO

Install the MOBOTIX camera (mounted to the CamIO wall mount foot) on the
CamIO housing. This step involves connecting the cables to the camera
(audio cables, Ethernet cables, CamIO control cable;

section 2.6

).

© MOBOTIX AG • Security-Vision-Systems • Made in Germany

www.mobotix.com • [e-mail]

24/56

MOBOTIX CamIO User Manual

2.3 Mounting the CamIO Wall Mount and the Control Cable

2.3.1 Mounting with an M12 Camera

• Unscrew the upper Allen screw in the original
foot of the mount, which holds the turn/tilt unit
in place (5mm Allen wrench, item12). Re­move the Allen screw, the washer and the hex
nut from the mount.

Remove cover

• Remove the cover.

• Gently pull the turn/tilt unit and all cables out
of the vertical opening of the original wall
mount foot.

• Remove the Allen screw of the bottom cover
and take off the cover.

Remove Allen screw,
washer and hex nut

Pull out

• MOBOTIX M12 cameras feature a pre-in­stalled insect protection, which effectively
prevents small animals from entering the
camera. Make sure that the condensation

escape vents remain open. Never push any

objects into the drain holes as this may
damage the plugs!

© MOBOTIX AG • Security-Vision-Systems • Made in Germany

www.mobotix.com • [e-mail]

Condensation escape vents

(do not block or damage)

MOBOTIX CamIO User Manual

• Insert the M12 control cable for the CamIO
from below into the turn/tilt unit of the cam­era. Remove the blue plug labeled RS-232
from the insect protection. Connect the HD 15
connector to the M12.

• Make sure that the camera's insect protection
remains firmly in place. Reinstall the bottom

cover of the mount.

25/56

• Insert the Ethernet cable and the M12 control
cable from below into the turn/tilt unit of the
CamIO wall mount foot.

• Insert the supplied cover into the free opening
of the CamIO wall mount foot.

• Insert the turn/tilt unit of the camera into the
vertical opening of the mount (all the way to
the stop).

• Place the hex nut into the corresponding hole, insert the Allen screw with
washer and lightly fasten the screw so that you can still easily turn the cam­era.

Insert cover

Insert the cover!

Maximum torque for all
screws is 1 to 1.2Nm
(0.74lbf ft)

© MOBOTIX AG • Security-Vision-Systems • Made in Germany

www.mobotix.com • [e-mail]

26/56

MOBOTIX CamIO User Manual

2.3.2 Mounting with an M22 Camera

• Unscrew the upper Allen screw in the original
foot of the mount, which holds the turn/tilt unit
in place (5mm Allen wrench, item12). Re­move the Allen screw, the washer and the hex
nut from the mount.

• Remove the cover.

• Gently pull the turn/tilt unit and all cables out
of the vertical opening of the original wall
mount foot.

Remove cover

Remove Allen screw,
washer and hex nut

Pull out

• Insert the M22 control cable for the CamIO
(USB connector first) from above into the turn/
tilt unit of the camera.

• Now guide the M22 control cable through the
bent opening of the USB plug.

• Attach the USB connector of the M22 control
cable to the USB socket of the camera.

• Push the USB plug over the USB connector
and the corresponding ring of the camera's
housing. It is very important that the rubber
plug reliably protects the housing and the USB
connector against moisture. This will guaran­tee the weatherproofness (IP65) of the cam­era.

© MOBOTIX AG • Security-Vision-Systems • Made in Germany

www.mobotix.com • [e-mail]

MOBOTIX CamIO User Manual

27/56

• Insert the Ethernet cable and the M22 control
cable from below into the turn/tilt unit of the
CamIO wall mount foot.

• Insert the supplied cover into the free opening
of the CamIO wall mount foot.

• Insert the turn/tilt unit of the camera into the
vertical opening of the mount (all the way to
the stop).

Insert cover

Insert the cover!

• Place the hex nut into the corresponding hole, insert the Allen screw with
washer and lightly fasten the screw so that you can still easily turn the cam­era.

Caution

Make sure that you are always using the proper plugs (NET for the
Ethernet cable, USB for the USB cable)!

Also make sure that the plugs are not bent or the cable is under
tension as this could lead to water entering the camera!

Maximum torque for all
screws is 1 to 1.2Nm
(0.74lbf ft)

© MOBOTIX AG • Security-Vision-Systems • Made in Germany

www.mobotix.com • [e-mail]

28/56

MOBOTIX CamIO User Manual

2.4 Mounting the CamIO Housing and Installing the Cables

2.4.1 Mounting the CamIO Housing on the Wall

The appendix of this manual contains a 1:1 drilling template for mounting the
CamIO. Use this template for drilling the holes for the dowels.

• Mount the CamIO using the supplied screws,
washers and dowels.

• Make sure that the installation cables are
guided though the opening at the bottom of
the CamIO and that the arrows next to the

OBEN / TOP label of the CamIO are pointing

upwards.

OBEN / TOP

• Remove the lid of the CamIO to continue with
the installation. To do so, gently lift the latch at
the top with a screwdriver (1), tilt the lid slightly
towards you (2) and remove the lid by pulling
it upward (3).

2

1

3

© MOBOTIX AG • Security-Vision-Systems • Made in Germany

www.mobotix.com • [e-mail]

MOBOTIX CamIO User Manual

2.4.2 Power Supply of the CamIO

You can supply power to the MOBOTIX CamIO using one of these two methods:

• Direct power supply: Mains power (230V~/115V~) is connected to termi­nals 1 and 2 of the CamIO's terminal connector at the bottom. The CamIO will
power a MOBOTIX camera and an external device attached to terminals 3
and 4. The external device will get the same voltage that has been con­nected to terminals 1 and 2 of the CamIO.

29/56

You can supply power to
the CamIO-AC and
CamIO-ACplus models
either directly or indi­rectly.

• Indirect power supply: The CamIO is powered by a PoE switch, which pro­vides power according to the Power-over-Ethernet standard IEEE 802.3af.
The attached MOBOTIX camera is powered by the same switch.

Note

The CamIO-PoE model supports indirect power supply via PoE. Provid­ing direct power with 230/115VAC is not possible when using the PoE
model. For additional information on the features of the individual
CamIO models, see chapter1.

Caution

When supplying power to an external device from the CamIO (termi­nals 3 and 4), the CamIO itself needs to be connected to the power
supply (terminals 1 and 2). This is possible on CamIO-AC and CamIO-

ACplus models by directly connecting 230/115V~ to terminals 1 and 2

of the CamIO. For the CamIO-PoE, the maximum allowed voltage at
terminals 1 and 2 is 48V~ or 68V=. This voltage is then available at
terminals 3 and 4 of the CamIO.

Power to the CamIO-PoE
can only be supplied in­directly via the network
cabling (PoE).

Make sure that an external load never exceeds 5A.

Caution

Only qualified personnel may install and open the CamIO and con­nect it to the mains power; make sure that the relevant regula­tions of your country are respected!

It is imperative that all electrical wires have been disconnected
from the mains power when working on or servicing the CamIO!
Please also make sure to adhere to the applicable regulations for
this kind of work!

MOBOTIX will not assume any responsibility for damages from
faulty installations or inappropriate use!

© MOBOTIX AG • Security-Vision-Systems • Made in Germany

www.mobotix.com • [e-mail]

30/56

MOBOTIX CamIO User Manual

Installing the power supply:

Use a two-wire cable (or any other suitable cable) to provide the power supply.
Make sure that you are respecting the minimum cable diameters.

Caution

The power supply cable to the CamIO needs to have a basic insula­tion level (BIL) of at least 230V/115V (depending on the mains volt­age). Never lay bell wires (BIL 50V) next to 230V or 115V cables!
Make sure that the fuse for this cable is not stronger
than 16A.

If a power cable with ground conductor is used
(three-wire cable), this wire must not be connected in
the junction box! Instead, connect the ground con­ductor of any attached device in the junction box.

Install the cable seals:

• Remove about 5cm (2in) of the outer insula­tion (sheath) of the power cable.

• Next, remove about 5mm (0.2in) of the wire
insulation.

Ground

Junction box

CamIO

Lamp

Bare wires

Wires with
insulation

According to common
regulation, no moisture
should enter between
the wires and the cable
insulation, since this may
lead to corrosion of the
cables. The silicone
compound and the cable
seals will reliably protect
the cables against mois­ture.

• Guide each wire into a separate finger of the
cable seal. Make sure that each finger only
contains a single wire (the clear plastic facili­tates this check, see figure).

• Puncture the tips of the cable seal fingers with
the wires.

Note

The supplied cable seals contain a small amount of silicone
compound, which facilitates pushing the wires through the
cable fingers. Make sure that you clean the wires and the
cable after mounting to remove any remaining silicone.

Outer cable
insulation

Cable fingers

Cable seal

© MOBOTIX AG • Security-Vision-Systems • Made in Germany

www.mobotix.com • [e-mail]

MOBOTIX CamIO User Manual

Connect the power supply to the CamIO:

• Puncture the blue seal with the end of the
black/brown wire (phase conductor L) and
guide it into terminal1. Tighten the screw to
lock the wire in place.

31/56

• Puncture the blue seal with the end of the
blue wire (neutral N) and guide it into termi­nal2. Tighten the screw to lock the wire in
place.

Cable fingers

Cable seal (3-wire)

If the blue seal has
been punctured at the
wrong place, you need to
replace the entire hou­sing to maintain the
IP65 protection class!

If a power cable with
ground conductor is used
(three-wire cable), this
wire must not be con­nected in the junction
box! Instead, connect
the ground conductor of
any attached device in
the junction box.

Note

Make sure that you are installing the supplied cable seals
when installing the cables for power supply, external devi­ces, sensors and audio devices. The seals will protect the ca­bles against water entering along the wires.

© MOBOTIX AG • Security-Vision-Systems • Made in Germany

www.mobotix.com • [e-mail]

32/56

MOBOTIX CamIO User Manual

2.4.3 Ethernet Connection of the CamIO

• Remove the outer insulation (sheath) of the
Ethernet cable and guide it through the proper
opening at the bottom of the CamIO housing
on the right–hand
side (see figure).

Make sure that you
are respecting the
cable assignment
and the minimum
cable diameters. For

additional information
on this topic, see
chapter 4,

Specifications

Technical

.

Make sure that you fol­low the proper wiring of
the Ethernet cabling!

• Lift all clamps of the Ethernet terminal.

• Push the wires of the Ethernet cable all the
way into the terminals and observe the cor­rect sequence while doing so. Do not remove
the insulation from any of the Ethernet wires.
Make sure that you are using the proper con­nection standard for the Ethernet connection
as outlined in section 2.1.4,

Wiring

).

Connectors and

• Secure the wires by firmly pushing down the
clamp until it locks in place. Gently pull on
each wire to make sure that it has been prop­erly clamped down.

© MOBOTIX AG • Security-Vision-Systems • Made in Germany

www.mobotix.com • [e-mail]

MOBOTIX CamIO User Manual

2.5 Connecting External Components to the CamIO

2.5.1 Connecting External Devices, Sensors and Audio Devices

The MOBOTIX CamIO supplies connectors for the following functions:

• Switch and supply power to external devices without individual power supply
with loads of up to 5A.

• Potential-free switching of external devices with individual power supply and
with loads between 100mA and 5A.

• Connect external sensors to the signal inputs of the camera (e.g. light barri­ers or external PIR sensors).

• Connect external audio devices to the camera (speakers and microphones
with an external pre-amplifier).

33/56

© MOBOTIX AG • Security-Vision-Systems • Made in Germany

www.mobotix.com • [e-mail]

34/56

MOBOTIX CamIO User Manual

Make sure that you follow the terminal assign­ment of the CamIO's bottom terminal connector.
Connecting and sealing the cables follows the
same instructions as for power cables (see sec­tion 2.4.2,
sure that you are adhering to the applicable
regulations in your country regarding the al­lowed cables when connecting the wires to the
terminal connector.

Power Supply of the CamIO

5 6

7 8 10 11 13 14 15 16

1 2 3 4

Terminal Part Name Remark

3

4

5

6

7
8

10

11
13
14
15
16

Out1 L (signal output 1)

Out1 N (signal output 1)

Out2a (signal output 2)

Out2b (signal output 2)

In2 + (signal input 2)
In2 - (signal input 2)
In1 + (signal input 1)
In1 - (signal input 1)
Speaker +
Speaker ­Line-In +
Line-In -

). Make

Ext. devices without individual po­wer supply, max. 5A, max.
500W lamps
Ext. devices with individual power
supply 5 to 230V~, max. 5A
(min. 5V=, 100mA)
Ext. sensor 2, 8 to 230V~ (48V~)
(min. 2mA)
Ext. sensor 1, 8 to 230V~ (48V~)
(min. 2mA)
Ext. speaker can be connected
directly, max. 2.5W/8Ω
Ext. microphone with ext. pre­amplifier

Note

Make sure that you are installing the supplied cable seals
when installing the cables for power supply, external devi­ces, sensors and audio devices. The seals will protect the ca­bles against water entering along the wires.

Make sure that you are respecting the minimum cable diameters!

Caution

The cables for power supply, external devices, sensors and audio
devices need to have a basic insulation level (BIL) of at least
230V/115V (depending on the mains voltage). Never lay bell wires
(BIL 50V) next to 230V or 115V cables!

© MOBOTIX AG • Security-Vision-Systems • Made in Germany

www.mobotix.com • [e-mail]

MOBOTIX CamIO User Manual

MOBOTIX CamIO Connection Example

35/56

© MOBOTIX AG • Security-Vision-Systems • Made in Germany

www.mobotix.com • [e-mail]

36/56

MOBOTIX CamIO User Manual

2.6 Mounting the Camera on the CamIO

Once the camera has been mounted to the foot of the CamIO wall mount, the Eth­ernet and control cables have been connected and optional external devices have
been attached, you can mount the CamIO/camera assembly to the CamIO hous­ing.

2.6.1 Connecting the Additional Speaker in the Wall Mount Foot

The foot of the wall mount has a built-in speaker, which can be used for audio out­put in connection with MOBOTIX M12 cameras. This speaker has a higher output
power than the camera speaker and is an excellent enhancement to the camera's
audio capabilities.

• Connect the two supplied audio cables to the
terminals 13 and 14 (Speaker) of the CamIO.

• If required, the addi­tional speaker (IP65) can
be pulled from its posi­tion in the wall mount

2

1

foot (1). To insert the
speaker again, push it
back into the foot (2).

© MOBOTIX AG • Security-Vision-Systems • Made in Germany

www.mobotix.com • [e-mail]

MOBOTIX CamIO User Manual

2.6.2 Connecting the Ethernet and the CamIO Control Cables

In order to connect the camera to the CamIO, you need to attach the Ethernet and
control cables of the camera to the CamIO.

37/56

• Insert the cover into the guides at the bottom
of the CamIO housing (1) and press at the top
of the cover until it clicks in place (2).

• Push the supplied rubber
plug (NET, item5) over the
Ethernet cable coming
from the camera, insert
the cable into the Ethernet
socket of the CamIO and
press the plug firmly into
the socket to seal off the
cable against moisture.

2

1

• Connect the control cable
from the camera to the re­maining socket of the
CamIO. Install the cable
and lock it in place using
the supplied screw
(item13) and the washer
(item14).

• Press the wall mount foot with the camera onto the CamIO housing and se­cure the foot on the CamIO using the four Allen screws (item6) and the
washers (item7). Take care not to squeeze and damage the cables when
mounting the foot onto the CamIO.

• Push the screw caps (item10) into the four openings of the Allen screws in
the foot of the CamIO wall mount.

Maximum torque for all
screws is 1 to 1.2Nm
(0.74lbf ft)

© MOBOTIX AG • Security-Vision-Systems • Made in Germany

www.mobotix.com • [e-mail]

38/56

MOBOTIX CamIO User Manual

2.7 Wiring, Fire Prevention, Lightning and Surge Protection

When installing the wiring inside or outside of buildings, make sure you always ad­here to the relevant regulations on wiring, fire prevention and protection against
lightning.

MOBOTIX recommends having MOBOTIX devices installed only by specialists ac­customed to installing network devices and having proper respect for the pertinent
regulations regarding lightning protection and fire prevention as well as the cur­rent technology for preventing damages from electrical surges.

More information is available at an institution such as the International Electro-
technical Commission (IEC, www.iec.ch) or at a manufacturer of protection de-
vices against lightning and electrical surges, such as Dehn (www.dehn.de).

2.7.1 Wiring

When installing the wiring, make sure you follow these guidelines:

• Data cable: Make sure to use only double-shielded
CAT 5/7 cable (S/STP) for Ethernet connections (see
section 3.3,

Manual

).

Connecting the Camera

in the

Camera

• Outdoors: Installing the camera outdoors requires spe­cial precautions and measures regarding the cables as
well as lightning and surge protection (see section

2.7.3,

Lightning and Surge Protection

• Wire lengths: The cable segments must not exceed the maximum allowed
cable lengths in order to ensure proper data transfer (see section 3.3,

necting the Camera

• Avoid induction: When running data cables parallel to existing regular
power lines or high-voltage wires, make sure you observe the minimum dis­tances to the power cables.

2.7.2 Fire Prevention

When installing the power lines to the camera, make sure you always adhere to
the relevant regulations on wiring and fire prevention at the site of the installation.

2.7.3 Lightning and Surge Protection

To prevent damage from lightning and power surges, make sure you follow these
guidelines:

• Lightning conductors: In areas exposed to lightning (e.g. on roofs), a dis­tance holder (1m (3ft) above and away from the camera) and proper light­ning conductors need to be installed in order to prevent lightning strikes into
the camera and to ensure that the energy of a lightning strike is properly led
to the ground.

in the

Camera Manual

).

Con-

).

© MOBOTIX AG • Security-Vision-Systems • Made in Germany

www.mobotix.com • [e-mail]

MOBOTIX CamIO User Manual

• Surge protection: Make sure you have installed proper protection against
electrical surges in order to prevent damage to the camera, the building and
the network infrastructure. This includes surge protectors for 19" racks, add­ing an uninterruptible power supply (UPS) to the MOBOTIX camera, and in­stalling surge arresters or similar for routers, switches, servers, etc.

39/56

© MOBOTIX AG • Security-Vision-Systems • Made in Germany

www.mobotix.com • [e-mail]

40/56

MOBOTIX CamIO User Manual

2.8 Accessories, Replacement Parts

CamIO Wall Mount Foot

The wall mount foot is used for mounting the cam­era to the MOBOTIX CamIO.

CamIO Housing

Replacement housing for all CamIO models.

M12 Control Cable (MX-CAMIO-OPT-M12)

Control cable for connecting the CamIO and an M12
camera.

M22 Control Cable (MX-CAMIO-OPT-M22)

Control cable for connecting the CamIO and an
M22M camera.

© MOBOTIX AG • Security-Vision-Systems • Made in Germany

www.mobotix.com • [e-mail]

MOBOTIX CamIO User Manual

Cable Seals

The seals will protect the cables against water that
could be entering along the wires.

M22 NET Plug

Plug for sealing off the Ethernet cable on M22M
camera models.

41/56

M22 USB Plug

Plug for sealing off the USB cable on M22M camera
models.

Additional CamIO Speaker

Replacement speaker with audio cables for the
CamIO wall mount foot.

© MOBOTIX AG • Security-Vision-Systems • Made in Germany

www.mobotix.com • [e-mail]

42/56

MOBOTIX CamIO User Manual

3 OPERATION OF THE CamIO

3.1 Activating the CamIO

Once the CamIO and the MOBOTIX camera have been properly installed (see
chapter2), you can set up the camera for proper operation. To begin with, it is nec­essary to establish the power supply of the CamIO (either 230V/115V directly or in­directly via the network cabling using a PoE switch).

Once the power supply to the CamIO has been established, the connected MO­BOTIX camera should also have power and you should be able to access the cam­era from any browser via the network (chapter3,
responding

After you have established the connection to the camera (Live screen in the
browser window), you need to activate the CamIO in the camera software (Admin
Menu> Manage Hardware Expansions). Activating the CamIO is a mandatory
step for using all features of the CamIO.

Camera Manual

contains more information on this topic).

Operating the Camera

, of the cor-

MOBOTIX M12 Cameras

MOBOTIX

M22M Cameras

Hint

To test the CamIO for proper operation with a MOBOTIX M12, simply
check if the additional speaker in the foot of the wall mount works (Ad-
min Menu> Loudspeaker and Microphone> Audio Output). When
clicking on the Te st button, you should hear the alarm from the cam­era speaker and the additional speaker of the CamIO.

Note

In order to use all features of the CamIO, make sure that you are
activating it in the camera software (Admin Menu> Manage
Hardware Expansions). Please note that you will need a software
version 3.3.1.x or higher on the MOBOTIX M22M and a software
version 3.1.0.x or higher on the MOBOTIX M12.

© MOBOTIX AG • Security-Vision-Systems • Made in Germany

www.mobotix.com • [e-mail]

MOBOTIX CamIO User Manual

3.2 Configuration Sample

The following example of a door intercom system demonstrates one possible ap­plication and shows the steps for properly configuring a MOBOTIX M12 with a
CamIO-AC/ACplus. Make sure that you have installed and setup the CamIO and
the MOBOTIX camera as described in chapter2.

43/56

Sample: Door intercom sy­stem with Video SIP and
additional lighting

3.2.1 Functional Overview

A MOBOTIX camera and a CamIO are used at the entrance of a building for access
control purposes and should open the door when prompted to do so.

If a visitor rings the doorbell (signal input1), the MOBOTIX camera automatically ac­tivates an additional source of light near the entrance (signal output1), plays back
a voice message ("Welcome to xyz company …") and establishes a video SIP con­nection to the receptionist's computer (or the guard on duty).

The softphone on the receptionist's computer signals an inbound video phone call
from the corresponding camera at the entrance. The receptionist accepts the call
and can talk to the guest at the entrance (using the additional speaker of the
CamIO and the microphone of the door intercom system, which is also connected
to the CamIO).

The image displayed on the softphone, i.e. the live video stream from the MOBOTIX
camera allows for visually checking the visitor. The softphone's keys provide func­tions for selecting certain image areas and for zooming the image (keys1, 7: zoom
control, keys2, 4, 6, 8: image section movement, key5: center the image).

If the receptionist would like to open the door for the visitor, he/she activates the
door opener (signal output2) using the softphone key0, allowing the visitor to en-

© MOBOTIX AG • Security-Vision-Systems • Made in Germany

www.mobotix.com • [e-mail]

44/56

MOBOTIX CamIO User Manual

ter the building. If required, the receptionist can manually switch the additional
lighting using the softphone keys: key 3 to switch the lights on and key 9 to switch
them off again.

In the meantime, the camera is automatically recording the video and audio
stream on a file server. Furthermore, the CamIO's rechargeable battery (CamIO­ACplus models only) protects the MOBOTIX camera against short-time power fail­ures. As an alternative, you can also use the doorbell system's UPS for this pur­pose.

3.2.2 Terminal Connections of the CamIO

• Terminals 1 and 2: Power supply of the CamIO and the additional lighting
(230V~/115V~).

• Terminals 3 and 4 (Out1): Additional lighting

• Terminals 5 and 6 (Out2): Door opener of the door intercom system

• Terminals 10 and 11 (In1): Doorbell of the door intercom system

• Terminals 13 and 14 (Speaker): Additional speaker in the foot of the CamIO
wall mount

• Terminals 15 and 16 (Line-In): Microphone of the door intercom system (with
external pre-amplifier)

3.2.3 Overview of the Configuration Steps

Configuring the MOBOTIX Camera (section3.2.4)

1) Activate arming of the camera

2) Configure recording

3) Configure SI event and switching of additional lighting (SO action)

4) Configure SI event and voice message (SD action)

5) Configure SI event and VoIP phone call (CL message)

Configuring the Softphone (section3.2.5)

6) Start and configure the softphone

© MOBOTIX AG • Security-Vision-Systems • Made in Germany

www.mobotix.com • [e-mail]

MOBOTIX CamIO User Manual

3.2.4 Configuring the MOBOTIX Camera

1) Activate arming of the camera

• Activate arming (Setup Menu> General Event Settings).

2) Configure recording

• Set up event storage on an external file server (Admin Menu> Event Stor­age).

45/56

© MOBOTIX AG • Security-Vision-Systems • Made in Germany

www.mobotix.com • [e-mail]

46/56

MOBOTIX CamIO User Manual

• Activate recording for VM event (Setup Menu> Recording).

• Activate VM event and set up video motion window (Setup Menu> Event
Settings).

© MOBOTIX AG • Security-Vision-Systems • Made in Germany

www.mobotix.com • [e-mail]

MOBOTIX CamIO User Manual

3) Configure SI event and switching of additional lighting (SO action)

• Configure SO action and activate action profile (Setup Menu> Actions).

47/56

4) Configure SI event and voice message (SD action)

• Activate and configure the speaker and the microphone (volume, micro­phone sensitivity in Admin Menu> Loudspeaker and Microphone); set
Audio Input temporarily to
voice message via the camera microphone).

• Record the voice message (Admin Menu> Manage Voice Messages); op­tional: upload sound file to the camera.

Microphone

(only required when recording the

© MOBOTIX AG • Security-Vision-Systems • Made in Germany

www.mobotix.com • [e-mail]

48/56

MOBOTIX CamIO User Manual

• Set Audio Input to
audio comes from the door intercom system's microphone).

• Set up and activate SI event (Setup Menu> Event Settings).

• Set up and activate SD message (Setup Menu> Messaging2), select
event and recorded voice message.

Line In

(Admin Menu> Loudspeaker and Microphone;

SI

© MOBOTIX AG • Security-Vision-Systems • Made in Germany

www.mobotix.com • [e-mail]

MOBOTIX CamIO User Manual

5) Configure SI event and VoIP phone call (CL message)

For more information on setting up the SIP telephony features of MOBOTIX cam­eras, read chapter 9,

• Configure the VoIP settings and activate VoIP (Admin Menu> VoIP Settings).

Telephony Features

in the

Software Manual

.

49/56

• Set up a phone profile (Admin Menu> Phone Profiles).

© MOBOTIX AG • Security-Vision-Systems • Made in Germany

www.mobotix.com • [e-mail]

50/56

MOBOTIX CamIO User Manual

• Add CL message to messaging profile and select phone profile (Setup
Menu> Messaging2; SD message has already been configured).

3.2.5 Configuring a Softphone

• Configure the softphone and make sure that it is running on the computer.

For more information on setting
up a softphone for use with
MOBOTIX cameras, read chap­ter 9,

Telephony Features

Software Manual

.

in the

© MOBOTIX AG • Security-Vision-Systems • Made in Germany

www.mobotix.com • [e-mail]

MOBOTIX CamIO User Manual

Notes

51/56

© MOBOTIX AG • Security-Vision-Systems • Made in Germany

www.mobotix.com • [e-mail]

52/56

p

Using the backup power
feature of the CamIO­ACplus requires a MO­BOTIX M12. M22 came­ras do not support this
feature yet.

MOBOTIX CamIO User Manual

4 TECHNICAL SPECIFICATIONS

CamIO-PoE

Mx-CAMIO-POE

Hardware Features

CamIO-AC

Mx-CAMIO-AC-230

Mx-CAMIO-AC-115

CamIO-ACplus

Mx-CAMIO-ACPLUS-230

Mx-CAMIO-ACPLUS-115

Currently, the audio
features of the CamIO
can only be used with
M12 cameras. A future
version of the CamIO
will support external
speakers and micro­phones also on M22 cam­eras.

Outdoor - weatherproof IP65 IP65 IP65

Power Supply

Integrated recharg. battery

Concealed cabling

Features

Audio Out (speaker/microphone)

Line In (microphone with pre-am

Signal outputs

Signal inputs

Input voltage (terminals 1 and 2)

Technical Specifications AC Models PoE Model

Output Out1 Max. voltage

Max. amperage

Max. lamp load

Output Out2

Inputs (In1, In2)

Speaker (Audio Out)

Max. voltage
Max. amperage

Max. lamp load

Min. voltage
Min. amperage
Max. voltage
Min. voltage
Min. amperage

Output rating

PoE

X

M12

X

X

2

2

8 to 48 V~

11 to 68 V=

-

M22M

-

-

2

2

230 V~ / PoE

115V~ / PoE

-

X

M12

X

X

2

2

230 V
5 A

500 W at 230 V~
300W at 115V~
240W at 230 V=
120W at 115V=

230 V
5 A

500 W at 230 V~
300W at 115V~
240W at 230 V=
120W at 115V=
5 V=

100 mA
230 V
8 V

2 mA

M22M

-

-

2

22

230 V~

115V~

~

~

~/325 V=

~/11 V=

2.5 W / 8 Ω

230 V~ / PoE

115V~ / PoE

X

X

M12

X

X

2

230 V~

115V~

~/68 V=

48 V
5 A

240W

~/68 V=

48 V
5 A

240W

5 V=
100 mA

~/68 V=

48 V
8 V

~/11 V=

2 mA

CamIO main board

Recharg. battery (ACplus only)

Max. power input

Endurance

3.5 W (without camera)

approx. 45 minutes (20°C/68°F)

approx. 20 minutes (-20°C/-4°F)

© MOBOTIX AG • Security-Vision-Systems • Made in Germany

www.mobotix.com • [e-mail]

MOBOTIX CamIO User Manual

Allowed Cable Diameters and Cable Lengths

Allowed Outer Diameters 3-wire cable 5-wire cable

Sheathed cables 8.2 to 11.0 mm (5/16 to 7/16 in) 9.5 to 12.5 mm (3/8 to 1/2 in)

Note

Make sure that the length of the Ethernet cable does not exceed

100m (300ft). The length of the cables for signal wires and exter­nal sensors is not restricted. You need to make sure, however, that

the minimum voltage at the corresponding terminal is reached.

53/56

ETHERNET
CAMERA

P

N

ETHERNET

© MOBOTIX AG • Security-Vision-Systems • Made in Germany

www.mobotix.com • [e-mail]

54/56

MOBOTIX CamIO User Manual

Terminal Connector for Power Supply, External Devices, Sensors and Audio De­vices

AWG:
American Wire Gauge (for
measuring cable diame­ters)

Allowed Cable Dimensions Solid AWG

Bottom terminal (terminals 1 to 16)

Cable diameters should be tailored to the electrical load and must follow the applicable regulations.

0.14 to 2.5 mm

2

26 to 14

5 6

7 8 10 11 13 14 15 16

1 2 3 4

Terminal Part Name Remark

1

2

3

4

5

6

7
8

10

11
13
14
15
16

Phase conductor L
Neutral conductor N

Out1 L (signal output 1)

Out1 N (signal output 1)

Out2a (signal output 2)

Out2b (signal output 2)

In2 + (signal input 2)
In2 - (signal input 2)
In1 + (signal input 1)
In1 - (signal input 1)
Speaker +
Speaker ­Line-In +
Line-In -

Direct power supply for CamIO
and Out1
Ext. devices without individual
power supply, max. 5A, max.
500W lamps
Ext. devices with individual power
supply 5 to 230V~, max. 5A
(min. 5V=, 100mA)
Ext. sensor 2, 8 to 230V~ (48V~)
(min. 2mA)
Ext. sensor 1, 8 to 230V~ (48V~)
(min. 2mA)
Ext. speaker can be connected
directly, max. 2.5W/8Ω
Ext. microphone with ext. pre­amplifier

Caution

The power supply cable to the CamIO needs to have a basic insula­tion level (BIL) of at least 230V/115V (depending on the mains volt­age). Never lay bell wires (BIL 50V) next to 230V or 115V cables!
Make sure that the fuse for this cable is not stronger
than 16A.

If a power cable with ground conductor is used
(three-wire cable), this wire must not be connected in

Ground

the junction box! Instead, connect the ground con­ductor of any attached device in the junction box.

Junction box

© MOBOTIX AG • Security-Vision-Systems • Made in Germany

www.mobotix.com • [e-mail]

CamIO

Lamp

MOBOTIX CamIO User Manual

W

W

W

W

Terminal Connector and Wiring of the Ethernet Connector

55/56

Allowed Cable Dimensions Solid AWG

Ethernet terminal (cutting clamps)

Cable diameters should be tailored to the electrical load and must follow the applicable regulations.

0.13 to 0.31 mm

2

26 to 22

Ethernet cabling today commonly follows the

T568B standard; older Ethernet cabling may

have been connected according to the T568A

standard:

Connection Standard T568B

Terminal TIA-568B Pair No.TIA-568 Color

8

7

4

4

Brown cable/white line

White cable/brown line

AWG:
American Wire Gauge (for
measuring cable diame­ters)

Variant B - T568B

6 (Rx-)

5

4

3 (Rx+)

2 (Tx-)

1 (Tx+)

3

1

1

3

2

2

Green cable/white line

White cable/blue line

Blue cable/white line

hite cable/green line

Orange cable/white line

hite cable/orange line

Connection Standard T568A

Terminal TIA-568A Pair No.TIA-568 Color

8

7

6 (Rx-)

5

4

3 (Rx+)

2 (Tx-)

1 (Tx+)

4

4

2

1

1

2

3

3

Brown cable/white line

White cable/brown line

Orange cable/white line

White cable/blue line

Blue cable/white line

hite cable/orange line

Green cable/white line

hite cable/green line

Variant A - T568A

© MOBOTIX AG • Security-Vision-Systems • Made in Germany

www.mobotix.com • [e-mail]

56/56

MOBOTIX CamIO User Manual

Declaration of Conformity

© MOBOTIX AG • Security-Vision-Systems • Made in Germany

www.mobotix.com • [e-mail]

MOBOTIX CamIO User Manual

MOBOTIX ... the new face of IP video

All images in this manual are genuine MOBOTIX camera images.

Enjoy the image quality!

Manufacturer: CEO:

MOBOTIX AG Dr. Ralf Hinkel
Luxemburger Str. 6
67657 Kaiserslautern Court of Registration:
Germany Amtsgericht Kaiserslautern

Registration Number: HRB 3724

Phone: [phone] Tax Code: 19/650/0812/1
Fax: [phone] Tax Office: Kaiserslautern

http://www.mobotix.com VAT ID: DE 202203501
[e-mail]

Download the newest version of this document from:
www.mobotix.com, Support section.

Technical information subject to change without notice!

© MOBOTIX AG • Security-Vision-Systems • Made in Germany

www.mobotix.com • [e-mail]

Megapixel

1280 x 960

software zoom

Security-Vision-SystemsSecurity-Vision-Systems

30 Frames/s

VGA (640 x 480)

10 fps Mega

-22°F to +140°F

Weatherproof

-30°C to +60°C, IP65

no heating necessary

IEEE 802.3af

PoE

network power

even in winter

microphone & speaker

Audio

bi-directional via IP

variable framerates

Video SIP Client

IP Telephony

alarm notify,

cam remote control

CamIO

User Manual

X

MOBOTIX

com

.

Video motion

multiple windows

precision pixel-based

lip-syncronized audio

Recording

event-ringbuffer

30 cams each 30 fps

Live viewing

30 cams at 30 fps

all on one screen

Backlight

safe using CMOS

without mechanical iris

Vandalism-protected

Lamp

Door

MOBOTIX

CamIO

Out1

8 to 48 V~

Out2

123

4

230 V~/115V~

56

7 8 10 11 1314 15 16

In1

In2

Line-In

Speaker

8

Microphone with
pre-amplifier

Speaker

8 to 230 V~ (8 to 48 V~)

8 to 230 V~ (8 to 48 V~)

Complete integration for web and security

Current PDF File:

www.mobotix.com > Support > Manuals

RJ45

Wall bracket

with cable cover

for RJ45 wall outlet

Robust

no moving parts

MX-UM-CamIO-EN-01

fiber glass housing

MOBOTIX AG • Security-Vision-Systems • Made in Germany

MOBOTIX ... the new face of IP video

www.mobotix.com • [e-mail] • 9.11.2007