Mobotix Mx2wire Media Converter User Manual
Mx2wire Media Converter
Mx2wire
PoE switch/injector
WLAN router
e.g. coaxial cable
www
e.g. telephone line
DSL router
Ethernet with PoE. Using 2-Wires.
up to 30 Mbps @ 500 m
e.g. coaxial cable
Mx2wire – The MOBOTIX Media Converter ...
up to 30 Mbps @ 200 m
e.g. bell wir e
up to 30 Mbps @ 100 m
e.g. power ca ble
PoE switch/injector
up to 30 Mbps @ 500 m
e.g. Cat-7-cable
DSL router
www
30
www.mobotix.com
•
Mx2wire transfers both data and power according to the PoE standard!
• Mx2wire does not require a separate power connection!
•
Mx2wire nuses existing telephone, power or antenna cables and therefore eliminates
the enormous amount of time and eort normally required for cabling!
•
Mx2wire is a quality product designed and manufactured entirely in Germany!
© MOBOTIX AG
Multiple Application Possibilities
Mx2wire can also connect a PC to the internet via an unused telephone line or an antenna cable. A set of devices,
consisting of two Mx2wire units, costs 298 Euro. The system was developed by MOBOTIX, manufactured in Germany
and can also be used in the new IP door intercom systems.
Technical Specifications Mx2wire
The HiRes Video Company
Technical Specifications Mx2wire Media Converter
Models
Data transfer speed up to 30 Mbps (depending on distance); see table below
Max. range
Interfaces Front: RJ45 (Fast Ethernet, PoE), DC jack
Certificates
Power supply
Mx2wire set pure white (additional models in development)
500 m (up to 30 Mbps)
Rear: Screw terminals to attach the two-wire cable
EMC (EN55022, EN55024, EN61000-6-1, FCC part15B,
AS/NZS3548)
Mx2wire modules are supplied via PoE (3 watts per module)
PoE (IEEE802.3af – based on capacity, 7 watts to PoE device)
Status display Status LED 1: Network connection, power supply
Weight 100 g
Operating
temperature
Dimensons 80 mm x 80 mm x 38 mm (flush-mounted model)
Standard delivery Mx2wire media converter set (color:pure white), mounting
Status LED 2: Active data transfer via AB wire,
user connected to the opposite side
-30 to +60°C (-22 to +140 °F)
80 mm x 80 mm x 45 mm (on-wall model)
parts, various panel frames, manual
Mx2wire Components (Shipped With Every Mx2wire Set)
Mx2wire se t
MX-2wire-Set-PW (pu re white)
An existing Mx2wire set contains all components necessary to set up an Ethernet connection using a two-wire cable (telephone,
coaxial, bell wire, Cat. 7).
Each one is supplied with a sender/receiver
unit, as well as accessories for flush-mounting
or on-wall assembly. The set is available in
pure white at present.
Comparative Tables For The Transfer Rates Of Data And Power
Antenna or coaxial cab le Thickness
0.6 mm
Inner
conductor
Teleph one line/bell wire Thickness
0.6 mm Data: 30 Mbps
0.8 mm Data: 30 Mbps
Circuit bo ard
• 2x Mx2wire circuit
board and housing
50 m 100 m 500 m
Data: 30 Mbps
PoE Class: 2
50 m 100 m 200 m
PoE Class: 2
PoE Class: 2
Panel frames
• 6x white concave,
convex and flat
frames (two of
each)
Front pane ls
• 2x front panel
Length
Data: 30 Mbps
PoE Class: 1
Length
Data: 30 Mbps
PoE Class: 1
Data: 30 Mbps
PoE Class: 2
Surface-mounted
Socket
• 2x white surface-
mounted socket
Accessories
• 2x cavity socket
• Mounting parts
Data: 30 Mbps
PoE Class: keine
Data: 25 Mbps
PoE Class: keine
Data: 30 Mbps
PoE Class: 1
Technical information subject to change without notice!
Installation cable Thickness
1.5 mm
Network installatio n Type
Cat-7 Data: 30 Mbps
Length
2
50 m 100 m 200 m
Data: 30 Mbps
PoE Class: 2
Length (Use of All 4 W ire Pairs: Combine 4x white and 4x colore d a nd attach wire-end sle eves)
200 m 300 m 500 m
PoE Class: 2
Data: 30 Mbps
PoE Class: 2
Data: 30 Mbps
PoE Class: 2
Data: 25 Mbps
PoE Class: 2
Data: 30 Mbps
PoE Class: 2
31
www.mobotix.com
Loading...