Mobotix AudioMount Quick Install Manual

The HiRes Video Company

EN

MOBOTIX AG • D-67722 Langmeil • Tel: [phone] • Fax: [phone] • www.mobotix.com

AudioMount: Quick Install

• Easy installation using adhesive film

• Integrated speaker and microphone

• Suitable for all FlexMount mono cameras

MX-FLEX-OPT-AM-BL

31.746_EN_V1_07/2013

Audio Extension for
FlexMount Cameras

Delivered Parts

Item Number Part Name

1.1 1 AudioMount

1.2 1 Black front cover with dome

1.3 4 Metal washer

1.4 5 Blue washer

1.5 5 Red washer

1.6 4 Allen screw M5x20

1.7 1 Allen wrench

1.8 1 Cable tie

1.9 1 Mount template sheet (no ill.)

The AudioMount is a mounting adapter for the S14M and S15M cameras allowing attachment to thin and
smooth surfaces (e.g., stainless steel plate, mailbox, etc.) using an adhesive film on the backside of the
AudioMount. Speaker and microphone are included so that the AudioMount can provide full intercom
functionality. Using the appropriate MOBOTIX accessories, you can also use the FlexMount camera in
conjunction with the AudioMount as a hemispheric door station (door station function with firmware 4.1.9
and higher).

1. Choose installation site

The AudioMount can be mounted horizontally or
vertically to (stainless) steel sheets with a thickness
of 1,2 mm to 3,0 mm.

2. Prepare mount surface

Drill holes for the lens, the microphone and the
speaker using the mount template sheet (item 1.9).
For alignment of the mount, mark the position of
the four notches (see a) on the side of the mount
surface where the mount is to be glued to.

3. Ax AudioMount

Remove the red protection film completely and
position the AudioMount concentrically to the
drilling in the panel with use of the centering
aid. Align horizontally or vertically by means of the
four notches (a) and then press the AudioMount
onto the panel. Break o the four pegs by pushing
them inwards (b).

Notes: Recommended working temp. 15 to 20°C
(59to 68 °F). The surface has to be clean, fat-free
and dry. Press hard when attaching the mount
(the glue is activated by pressure!)

Installation of the AudioMount

Installation of the Camera

Micro Spk. MxBus

1. Temporarily attach camera

To make the cable connection easy, temporarily
attach the camera upside down onto the AudioMount
with the two Allen screws (item 1.6).

2. Attach connection cables

Open the camera housing with a 2,5 mm Allen
wrench (provided with the camera). Connect the
required cables:

•

Lead the AudioMount´s microphone and speaker
cables as well as the MxBus cables (when
using MxBus modules) through the camera
opening for additional cables and connect
them (see S15 Camera Manual, Chapter 2).

• Insert the patch cable into the left opening of
the camera and secure it with the blue bayonet
catch (see S15 Camera Manual, Chapter 2).

1.1

1.2

1.3

1.5

1.4

1.6

1.7

1.8

a)

b)

Example: metall sheet not included in delievered parts

The HiRes Video Company

EN

MOBOTIX AG • D-67722 Langmeil • Tel: [phone] • Fax: [phone] • www.mobotix.com

AudioMount: Quick Install

1. Remove and re-attach camera

Remove the Allen screws (item 1.6), turn the camera
around and attach it to the AudioMount. Make
sure that you lead the cables on the left side
around the four black mounting pegs. Screw the
camera with the Allen wrench (item 1.7) to the
mounting pegs using Allen screws (item 1.6) and
metal washers (item 1.3).

Thickness of material: The AudioMount is constructed
for sheet metals with a 3mm thickness. If the
material is less than 2,4 mm thick, additional
washers have to be put between the mounting
pegs and the back of the S15, so that the dome
of the camera lens attains its optimal position.

2. Attach cable tie

Remove the protective foil from the cable tie (item

1.8) and stick it to the left side of the camera.

Secure the audio cables with the cable tie.

Finishing the Installation

MxBus

AudioMount with

mounted S15M

Door

Door Opener and
Lock Sensor

DoorMaster

Door Sensor

e.g., MX-232-IO-Box to

connect door bells

MxBus

NPA-PoE-Set

Remote Stations

Patch Cable (RJ45)

Setup of the Camera

You find detailed information to the standard installation in the S15 Camera Manual, Section 3 „Operating
the Camera“.

1. Establish PoE power supply

2. Put camera into operation

3. Optional: Start auto configuration

If you would like to use the FlexMount camera in conjunction with the AudioMount as a door station, you
can run the auto configuration with the aid of the camera buttons now. To do this, reboot the camera by
disconnecting and reconnecting the PoE power supply. After the reboot, press the camera buttons according
to the description in the S15 Camera Manual, ” Setting up an S15 FlexMount as a Door Station“ and configure
the connected door station modules (e.g., bell and DoorMaster).

• When using a solid core wire cable (instead
of a patch cable), lead that cable through
the camera opening for “additional“ cables.
Remove the bayonet catch on the left camera
opening and insert the cable plug that holds
the additional cables (see S15 Camera Manual,
Chapter 2).

• If a USB decive is to be connected, insert the
MiniUSB cable into the MiniUSB plug (see S15
Camera Manual, Chapter 2).

3. Attach housing cover

Attach the black front cover with dome included
in the delivered parts (item 1.2) to the camera and
fasten it in place. The previously removed white
front cover is not needed.

Thickness/Material Washer

1,20 - 1,79 mm blue

1,80 - 2,39 mm red

2,40 - 3,00 mm none

Copyright © MOBOTIX AG 2013 • Made in Germany • Technical information subject to change without notice.

Display available in the future