MobileView MVC9800 Quick Reference Manual

MVC-9800 Camera Install Guide

p.4

Copyright © Safe Fleet March 2018 | All rights reserved | Part #: 700-1114 R1

Product Overview

This install guide follows the following camera models:

• MVC-9800-28-WI, MVC-9800-40-WI

• MVC-9800-40-WI-S, MVC-9800-28-WI-FF,
MVC-9800-80-WI-FF

Note:

• S = Side facing, FF = Forward facing

Package Contents

Inspect the package contents for
visibly damaged or missing parts.
If found, retain original packaging,
contact your supplier, and do not use
the camera. Your package includes:

• Camera, drill template

• Quick Reference Guide

• Torx wrench

• Rubber plug

• Twist lock weather pack
connector

• Hex wrench with FF models

• Wedges

• Screws

• Pads with -S models

• Brush guard for all models except
FF model

Cable Requirements

• PoE (802.3af): Cat5, 24 AWG
stranded or better

• Standard RJ45 Jack with Twist­Lock

• Analog Video: BNC Jack, 75 Ohm

Supported Plugins

• Web Components

• QuickTime v7.7.4

Installation Environment

Observe the following when installing an
MVC-9800 camera:

• Electrical: Only qualied service members
should install wiring to prevent overload
of the power cord. Always use a genuine
MobileView PoE product, such as MVNS­3200 PoE Switch to power the camera.

• Ventilation: Install camera in a well
ventilated position.

• Temperature: Do not operate the camera

beyond the specied temperature,

humidity or power source ratings.

• Service: Only qualied service personnel
should repair and service the camera,
otherwise the warranty will become
invalid. Do not dismantle the camera,
except as required for normal installation
to avoid personal injury.

• Clean: If cleaning is necessary, use a
clean cloth with ethanol to gently wipe the
camera.

Service

If your 9800 Series Camera is to be returned for service, please call toll free

1.877.630.7366, or 1.844.899.7366, and provide the model and/or serial# of your unit.
Ask for a Return Merchandise Authorization (RMA) number. An RMA# allows the Service
Technicians to better track your product when it comes in for service. Please show the
RMA# on the outside of the package. ANY PRODUCT SENT WITHOUT AN RMA# MAY BE

REFUSED.

Adjusting Image Orientation

Rotate image 180 if needed.

1. Open Basic Conguration.

2. Under Adjustment, select 180 degrees from the Image Adjustment drop-down, and
click Apply.

3. Select Video Stream Preview and click Alarm.

4. Review the image in the Video Stream Preview window. If the image is incorrect,
select a different Image Adjustment option and click Apply again.

Technical Support

• Email: [e-mail]

• Phone: [phone]

Documentation

Additional copies of this guide, along with other
supporting documentation can be found on the SafeFleet
Community:

• https://community.seon.com/documents/

p.2

p.3

Fold Here

Camera Description

1

2

3

4

5

9

8

7

6

1. LED Indicator.

- Solid Red: Device is powered on

- Solid Green: Device communicating

2. Lens

3. Front Cover

4. Mounting Base

5. SD Card

6. Mic

7. IR LED

8. Camera Enclosure

9. Network Cable

Mounting the Camera

1. Prepare the mounting surface

2. Loosen the two screws on the camera cover and
remove the camera cover.

3. Using the supplied template, mark the mounting
area and drill holes in the surface.

4. Direct the cable through the silicone pad, silicone
stopper, and the wall.

5. Align the silicone stopper to hole A of the drill
template. Mount the camera on the surface
using the proper mounting screws. Rivnuts
with #8 machine screws with lock washer are
recommended when mounting camera on exterior
of vehicle.

6. Loosen the adjustment screw and adjust the
camera to the desired surveillance angle. Tighten
the screw to secure the desired position.

Side View

Access Camera Online

You can access and congure the camera settings using the Camera Web Browser

via Internet Explorer. Only one camera can be accessed at a time, and Active X
controls must be enabled.

1. Enter the camera IP address and press Enter.

2. Enter the user name and password. Default login is:

• user name: admin

• password: 1234

3. Click Login. The Basic Conguration window displays.

4. Change the IP address to the required value and click Apply to save settings.

7. Place the camera cover over the camera and fasten
using the cover screws.

8. When camera is installed on the exterior of vehicle,
always use the Twist Lock Weather Pack connector
housing on the RJ45 cable that mates to the camera to
protect the cable connection from corrosion.

Web browser functions

• Live View: View live video (IE v11, Safari v5.1.7). Change aspect ratio, stream to

view and plugin to play the video.

• Basic Conguration: Adjust IP settings, stream parameters, image, overlay, day/

night IR settings and preview video.

• Advanced Conguration: Firmware upgrade, restore defaults, manage users, setup

time, tamper and exception events, region of interest, privacy mask, storage, and
modify network parameters for TCP/IP, SNMP, NAT, RTSP and SSH.

• Quick Status: View camera model, serial number, rmware version and IP address.

• Logout: Click to log out of the system

• Apply: Click to save changes.

Silicone Stopple

Silicone Pad