MobileView MVC-9002-28-WI, MVC-9002-40-WI, MVC-9102-28-BK, MVC-9102-28-WI, MVC-9102-40-WI Quick Manual

MobileView® 9002 Series Exterior Analog/IP Camera Quick Guide

Product Overview

This is the Quick Guide for MobileView camera models:

• MVC-9002-28-WI

• MVC-9002-40-WI

Installation Environment

When installing your product, consider the following:

• Electrical: Install electrical wiring carefully. It should be done
by qualified service personnel. Always use a proper PoE
switch or a 12 VDC power supply to power the camera. Do
not overload the power cord or adapter. PoE and 12VDC
power sources should NOT be used together; choose only
one.

• Ventilation: Ensure that the location planned for the
installation of the camera is well ventilated.

• Temperature: Do not operate the camera beyond the
specified temperature, humidity or power source ratings. The
operating temperature of the camera is between -30 to
+65°C.

• Servicing: Do not attempt to repair this camera yourself. Any
attempt to dismantle this product, except as required for
normal installation, will negate the warranty and may also
result in injury. Refer all servicing to qualified service
personnel.

• Cleaning: Do not touch the lens with your fingers. If cleaning
is necessary, use a clean cloth with ethanol and gently wipe
the camera.

Package Contents

Check the package and contents for visible damage. If any
components are damaged or missing, do not attempt to use the
unit; contact the supplier immediately. If the unit is returned, it
must be shipped back in its original packaging.

Package contents:

• Camera

• Y Splitter cable (optionally used if 12VDC power is supplied
via Cat5)

• Hex wrench

• Quick Guide

• Drill Template

• Molex connector/pins

• Guard

Cable Requirements

For proper operation, adhere to the following cable and power
requirements for the cameras. All network cabling must be
installed according to applicable codes and regulations.

The MV 9002 Exterior Camera figure lists the requirements for the
cables that connect to the camera. The camera has two options to
receive power; only one should be used at a time.

Table 1: Recommended power cable requirements

PoE(802.3af): Cat5, 24 AWG Stranded or better

12VDC: 18 AWG, or larger

Camera Description

MV 9002 Exterior Camera

1. Cover

2. Bubble

3. IR

4. Base

5. Lens

6. BNC Cable

7. 12VDC Molex connector

8. Ethernet RJ45 cable

9. Reset Button

Setting up the Camera

To quickly put the camera into operation:

1. Prepare the mounting surface.

2. Mount the camera using the appropriate fasteners. Refer to
the Mounting the Camera section.

P/N 1073197A • REV 01.00 • JULY 2016 1

3. Set up the camera's network and streaming parameters to
control the camera over the network. Refer to the Accessing
the Camera over the Internet section.

4. Program the camera to suit its location.

Note: Refer to the MobileView 9002 and 9102 Series Analog/

IP Camera User Manual for more information.

Mounting the Camera

To Mount the exterior camera:

1. Use the supplied template to mark out the mounting area.
Drill the screw holes on the surface. Rivnuts with #8-32
machine screws (or larger) are recommended.

2. Loosen the cover screws, so cover can be removed. Secure
the mounting base to the surface with appropriate screws.

Accessing the Camera over the Internet

Use the camera web browser to access and configure the camera
over the Internet (Microsoft Internet Explorer). Only one camera is
accessible from a single web browser window.

To access the camera online:

1. In the Web browser, enter the camera's IP address.
The default is 192.168.1.70.
The Login dialog box appears.

Note: Ensure that the Active X controls are enabled.

2. Enter your user name and password.
User name: admin
Password: 1234

3. Click Login. The web browser window appears in live view
mode.

Overview of the Camera Web Browser

3. Loosen the adjusting screw to adjust the pan, tilt and rotation
angle, then re-tighten the adjusting screw.

4. Reinstall the cover screws.

UI 9002 Live Screen -Manual

Name Description

Live View Click to view live video.

Basic Configuration Click to display the basic configuration screen for

setting up the camera.

Advanced
Configuration

Current user Displays current user logged on.

Logout Click to log out from the system. This can be done at

Start/stop live view Click to start/stop live view.

Capture Click to take a snapshot of the video. The snapshot

Click to display the advanced configuration screens
for setting up the camera.

any time.

will be saved to the default folder in JPEG or BMP
format.

2 MMobileView® 9002 Series Exterior Analog/IP Camera Quick Guide

Start/stop recording Click to record live video.

Digital Zoom Click to enable digital zoom.