Portable Speaker
TAS4405
TAPR802
User manual
Register your product and get support at
www.philips.com/support
Contents
1 Important 2
Safety 2
2 Your Wireless portable speaker 3
Introduction 3
What's in the box 3
Overview 3
3 Get started 4
Charge the built-in battery 4
Install batteries for the microphone 4
Install a micro-SD card 5
5 Power on/off 5
6 Use Bluetooth devices 6
7 Micro-SD card mode 7
8 Mix your sound with an audio source 7
Record 7
9 Product information 8
10 Notice 8
Compliance 8
Care of the environment 8
FCC Statement 9
Trademark notice 9
EN
1
1 Important
Safety
Warning
• Never remove the casing of this product.
• Never lubricate any part of this product.
• Never place this product on other
electrical equipment.
• Keep this product away from direct
sunlight, naked fames or heat.
• Read and follow these instructions.
• Make sure that there is enough space
around the product for ventilation.
• Refer all servicing to qualied service
personnel. Servicing is required when the
product has been damaged in any way, such
as power-supply cord or plug is damaged,
liquid has been spilled or objects have fallen
into the product, the product has been
exposed to rain or mositure, does not
operate normally, or has been dropped.
• Only use attachments/accessories specied
by the manufacturer.
• Use only power supplies listed in this user
manual.
• Unplug this product during lightning stroms
or when unused for long periods of time.
• This product should not be exposed to
dripping or splashing.
• Do not place any sources of danger on the
product (e.g. liquid lled objects, lighted
candles).
• Where the plug of the Direct Plug-in
Adapter is used as the disconnect device,
the disconnect device shall remain readily
operable.
• Do not use this product near water.
• Install in accordance with the
manufacturer’s instructions.
• Do not install near any heat sources wuch
as radiators, heat registers, stoves, or
other apparatus (including ampliers) that
produce heat.
2
EN
2 Your wireless
Quick start guide
TAPR802
AAA x 2
1
4
5
2
3
6
7
8
9
portable speaker
Congratulations on your purchase, and
welcome to Philips! To fully benet from the
support that Philips offers, register your product
at www.philips.com/welcome.
Introduction
With this speaker and microphone, you can
• enjoy audio from a Bluetooth device,
• enjoy audio from a micro-SD card,
• one touch recording to micro-SD card.
What's in the box
Please check and identify the contents of your
package:
• Wireless portable speaker
• Wireless microphone
• USB cable
• Quick start guide
• Safety sheet
Overview
a
• Press and hold for 2 seconds to
power on or off.
b
• Press to start or stop the recording
of audio from both the wireless
microphone and the speaker.
c
• Press to select Bluetooth or micro-SD
card source.
d /
• Press to adjust the volume.
e
• Press to play or pause.
• Press twice to skip to the next track.
f Micro-USB charging port
g Micro-SD card slot
h Battery compartment lid
i Microphone power switch
EN
3
3 Get started
5V
A
Install batteries for the
microphone
Always follow the instructions in this chapter in
sequence.
Charge the built-in battery
The speaker is powered by a built-in
rechargeable battery.
Note
• Fully charge the built-in battery before using.
1 Open the battery compar tment lid.
2 Install 2 AAA alkaline batteries (not
provided) with the correct polarity.
3 Close the battery compar tment lid
AAA x 2
Connect the USB cable between the microUSB socket on the speaker and a USB socket
on your computer or a charger.
LED indicator (Power)
Flashing red Being charged
Off Fully charged
4
EN
Install a micro-SD card
5 Power on/off
1 Open the lid of the card slot.
2 Insert a micro-SD card (not provided) with
the pin side facing down till you hear a
click. Then close the lid of the card slot.
1 Press and hold for 2 seconds to power
on or off the speaker.
2 sec.
2 Slide up the power switch to power on the
microphone.
EN
5
6 Use Bluetooth
devices
With this speaker, you can enjoy audio from
your Bluetooth device.
Note
• Make sure that the Bluetooth function is enabled on
your device.
• Keep away from any other electronic device that may
cause interference.
1 Press and hold for 2 seconds to enter
the Bluetooth pairing mode.
Philips S4405
10m
BEEP
2 sec.
2 Select “Philips S4405” in the Bluetooth list
on your device.
» If a message prompts for permission
for Bluetooth connection, conrm it.
» If a password is required, enter 0000
and then conrm.
» The speaker beeps when successfully
connected.
6
EN
LED indicator (Bluetooth)
Blinking blue Bluetooth pairing
Steady blue Bluetooth connected
Note
• To disconnect, disable the Bluetooth connection with
this product on your device or press again to switch
to micro-SD card mode.
7 Micro-SD card
8 Mix your sound
mode
You can enjoy audio from a micro-SD card that
stores audio les.
Press repeatedly to select the micro-SD
source. The Bluetooth LED indicator will be
turned off for micro-SD auto playback.
with an audio
source
Note
• For the best vocal quality, keep a distance of ?? cm
between the microphone and the speaker.
By using the wireless microphone, you can mix
your sound with an audio source
Record
In the Bluetooth mode, press to star t or stop
the recording.
LED indicator (REC)
Blinking red Error (no micro-SD card
inserted or the card is full)
Solid red Recording
EN
7
9 Product
information
Note
• Product information is subject to change without prior
notice.
General information
Power supply:
Speaker driver 1.5”
Charging time
(Speaker)
Playtime 6 hours
Built-in Lithium battery
(Speaker)
Dimensions (Speaker) 105 x 105 x 38 mm
Weight (Speaker)
Bluetooth
Bluetooth version V4.2
Bluetooth range 5 m / 16.5 ft
5V 1.5A
2.5 hours
3.7V, 1500mAh
0.29 g
10 Notice
Any changes or modications made to this
device that are not expressly approved by
MMD Hong Kong Holding Limited may void
the user’s authority to operate the product.
Compliance
Hereby, MMD Hong Kong Holding Limited
declares that this product is in compliance with
the essential requirements and other relevant
provisions of Directive 2014/53/EU. You can nd
the Declaration of Conformity on
www. philips.com/support.
Care of the environment
Disposal of your old product and battery
Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused.
This symbol on a product means that the
product is covered by European Directive
2012/19/EU.
This symbol means that the product contains
batteries covered by European Directive
2013/56/EU which cannot be disposed of with
normal household waste.
Inform yourself about the the local separate
collection system for electrical and electronic
products and batteries. Follow local rules and
8
EN
never dispose of the product and batteries
with normal household waste. Correct disposal
of old products and batteries helps prevent
negative consequences for the environment and
human health.
Removing the disposal batteries
To remove the disposable batteries, see batter y
install section.
Environmental information
All unnecessary packaging has been omitted.
We have tried to make the packaging easy to
separate into three materials: cardboard (box),
polystyrene foam (buffer) and polyethylene
(bags, protective foam sheet.)
Your system consists of materials which can
be recycled and reused if disassembled by a
specialized company. Please observe the local
regulations regarding the disposal of packaging
materials, exhausted batteries and old equipment.
Warning: Changes or modications not
expressly approved by the party responsible for
compliance could void the user’s authority to
operate the equipment.
Note: This equipment has been tested and found
to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate
radio frequency energy and, if not installed
and used in accordance with the instructions,
may cause harmful interference to radio
communications. However, there is no guarantee
that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception, which
can be determined by turning the equipment off
and on, the user is encouraged to try to correct
the interference by one or more of the following
measures: (1) Reorient or relocate the receiving
antenna. (2) Increase the separation between
the equipment and receiver. (3) Connect the
equipment into an outlet on a circuit different
from that to which the receiver is connected. (4)
Consult the dealer or an experienced radio/TV
technician for help.
RF Warning Statement
The device has been evaluated to meet general
RF exposure requirements. The device can be
used in portable exposure conditions without
restriction.
FCC Statement
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful
interference, and (2) This device must accept any
interference received, including interference that
may cause undesired operation.
Trademark notice
The Bluetooth ® word mark and logos are
registered trademarks owned by the Bluetooth
SIG, Inc. and any use of such marks by MMD
Hong Kong Holidng Limited is under license.
Other trademarks and trade names are those of
their respective owners.
EN
9
Specications are subject to change without notice.
Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under license.
This product has been manufactured by and is sold under the responsibility of MMD Hong Kong Holding Limited or
one of its afliates, and MMD Hong Kong Holding Limited is the warrantor in relation to this product.
Loading...